home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
DOS/V Power Report 2001 January
/
VPR0101B.BIN
/
BIOS
/
EPOX
/
6VBA0913
/
6vba0913.exe
/
README.TXT
< prev
next >
Wrap
Text File
|
2000-10-05
|
7KB
|
155 lines
README.TXT File for BIOS Flash Updating
Bios filename: 6vba0913.bin
Bios date: 09/13/2000
Bios size: 256 KB (For 2Mb BIOS EEPROM)
Bios checksum: n/a
Model support: EP-3VBA, EP-3VBA+, EP-3VBA3, EP-6VBA, EP-3VBM-H,
EP-3VBM, P2-150A
!!!WARNING!!!
Never attempt to Flash your BIOS from a hard disk, DOS Window, DOS
shell, or in Windows NT. If your system is working without problems
or conflicts, then it is not recommended that you flash your BIOS.
Improper flashing procedures may result in a dead system! Follow the
these instructions carefully.
Files included in this download:
README.TXT Text file with BIOS Release & Application Notes.
UPDATE.BAT Batch file for the Flash BIOS update process.
RESTORE.BAT Batch file for the Flash BIOS restore process.
xxxxxxxx.BIN BIOS binary file used by UPDATE.BAT.
AWDFLASH.EXE Program used to Flash BIOS code to the EEPROM.
Enhancements & Fixes for this BIOS release:
Added support for W49F002U flash ROM.
----------------------------------------------------------------------
BIOS Download Instructions
Download the xxxxxxxx.EXE file corresponding to your model from the
EPoX website to an empty directory on your hard disk or floppy. Run
the downloaded xxxxxxxx.EXE file and it will self extract into the
above listed files.
Copy these extracted files to a bootable DOS floppy disk. Note: the
DOS floppy disk should contain NO device drivers or other programs
that load during the boot other than the operating system itself.
----------------------------------------------------------------------
BIOS Update Instructions
Boot using your DOS floppy disk to the 羨:\> command prompt. At the
DOS command prompt type: UPDATE
When the Flash program completes restart the computer, remove the DOS
floppy disk, and enter your CMOS setup by pressing the <DEL> key
immediately. Using the arrow keys select 銑OAD SETUP DEFAULTS and
when prompt to confirm press 塑 and 薦NTER. Press 詮10 to Save &
Exit the BIOS. When prompted to confirm again press 塑 and 薦NTER.
The system flash is now completed.
Note: During the use of UPDATE a backup of your original BIOS
date/code will be saved in the same directory as the UPDATE file. It
will be called 前LD.BIN and can be used with the restore
instructions below in case you need to revert back to the original
BIOS date/code.
----------------------------------------------------------------------
BIOS Restore Instructions
Use of the restore procedure requires the OLD.BIN file created in the
update procedure above! Boot using your DOS floppy disk to the 羨:\>
command prompt. At the DOS command prompt type: RESTORE
When the Flash program completes restart the computer, remove the DOS
floppy disk, and enter your CMOS setup by pressing the <DEL> key
immediately. Using the arrow keys select 銑OAD SETUP DEFAULTS and
when prompt to confirm press 塑 and 薦NTER. Press 詮10 to Save &
Exit the BIOS. When prompted to confirm again press 塑 and 薦NTER.
The system flash is now completed and should now be reverted back to
the original BIOS date/code.
----------------------------------------------------------------------
BIOS flash failed
If you have access to an old un-accelerated ISA video card, you might
be able to recover your BIOS. Remove all cards and drives from your
system, except for the ISA video card and the floppy drive. Then try
to boot from a system disk (a bootable floppy with only the flash
programs and corresponding BIOS binary). If you are able to boot to
the floppy, flash your BIOS according to the directions above.
----------------------------------------------------------------------
I get out of memory errors when I flash my BIOS!
On some system configurations, even with a clean boot disk, you will
get an out of memory error (insufficient memory) when you try to
flash your BIOS. The solution is simple: Try bypassing the startup
files by pressing the following keys during startup using you
bootable floppy disk. Attempt the FLASH again.
DOS 6.2x boot disks - press F5 to bypass.
WINDOWS 95/98 boot disks - press F8 and select "Safe command prompt."
Lastly try using a MS-DOS 6.x boot disk.
----------------------------------------------------------------------
Manual use of the AWDFLASH Utility
Most users will find that our UPDATE and RESTORE batch files can
accomplish the BIOS flash with the majority of configurations. But if
you wish to manually use the AWDFLASH utility, below are the most
common command line usages and parameters.
Awdflash 7.33 (C)Award Software 1999 All Rights Reserved
Usage: AWDFLASH [FileName1] [FileName2] [/<sw>[/<sw>...]]
FileName1 : New BIOS Name For Flash Programming
FileName2 : BIOS File For Backing-up the Original BIOS
<Swtches>
?: Show Help Messages
py: Program Flash Memory pn: No Flash Programming
sy: Backup Original BIOS To Disk File sn: No Original BIOS Backup
Sb: Skip BootBlock programming sd: Save DMI data to file
cp: Clear PnP(ESCD) Data After Programming
cd: Clear DMI Data After Programming
cc: Clear CMOS Data After Programming
R: RESET System After Programming
cks: Show update Binfile checksum
Tiny: Occupy lesser memory
E: Return to DOS When Programming is done
F: Use Flash Routines in Original BIOS For Flash Programming
LD: Destroy CMOS Checksum And No System Halt For First Reboot
After Programming
cksXXXX: Compare Binfile CheckSum with XXXX
Example: AWDFLASH 2a59i000.bin /py/sn/cd/cp/cks2635
----------------------------------------------------------------------
DISCLAIMER
THE SOFTWARE AND BIOS ARE PROVIDED "AS IS" WITHOUT ANY EXPRESS OR
IMPLIED WARRANTY OF ANY KIND INCLUDING WARRANTIES OF MERCHANTABILITY,
NONINFRINGEMENT OF INTELLECTUAL PROPERTY, OR FITNESS FOR ANY
PARTICULAR PURPOSE. IN NO EVENT SHALL EPOX OR ITS SUPPLIERS BE LIABLE
FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION)
ARISING OUT OF THE USE OF OR INABILITY TO USE THE SOFTWARE AND BIOS,
EVEN IF EPOX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
BECAUSE SOME JURISDICTIONS PROHIBIT THE EXCLUSION OR LIMITATION OF
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. EPoX and its suppliers further do
not warrant the accuracy or completeness of the information, text,
graphics, links or other items contained within these materials.
EPoX reserves the right to change specifications or discontinue
products at any time with no prior warning. EPoX makes no commitment
to update any BIOS.
v1.0 091699 JRH