home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
DOS/V Power Report 1999 October
/
VPR9910B.BIN
/
DRIVER
/
NO9
/
04062027
/
04062027.exe
/
READ_ME.TXT
< prev
next >
Wrap
Text File
|
1999-02-27
|
21KB
|
546 lines
--------------------------------------------------------------------
Number Nine - Single Head - Display Driver
for the Number Nine Revolution (TM) IV
Microsoft Windows NT 4.0
Version: 04.062.027
------------------------------------------------------------------
This file contains the latest information about the Revolution IV
for Windows NT 4.0 Installation disk.
*** NOTE: You should be using Windows NT 4.0 Service Pack 3 or later
before installing the Revolution IV in your system!
This installation disk includes Revolution IV display drivers for
Windows NT 4.0, as well as the HawkEye IV Display Utility.
------------------------------------------------------------------
CONTENTS
------------------------------------------------------------------
INSTALLING OR UPGRADING REVOLUTION IV
INSTALLING HAWKEYE IV UTILITY
SUPPORTED RESOLUTIONS
REVOLUTION IV SUPPORT FOR 3D
PRESENT CAPABILITIES
SUPPORTED CONFIGURATIONS
SOFTWARE UPGRADES
INTERNET
KNOWN RESTRICTIONS AND PROBLEMS
REMOVING HAWKEYE FOR WINDOWS NT
OTHER PROBLEMS
PRODUCT REGISTRATION
CONTACTING NUMBER NINE VISUAL TECHNOLOGY CORPORATION
TRADEMARKS
------------------------------------------------------------------
INSTALLING OR UPGRADING REVOLUTION IV DRIVERS
------------------------------------------------------------------
Steps for installing the Revolution IV driver for Windows NT 4.0
1. After installing the Revolution(tm)IV board in the system,
start Windows NT in VGA mode by selecting the Windows NT
Workstation Version 4.00 (VGA mode) option from the NT Boot
Menu.
2. When NT finishes loading, log in as a user who has permission
to change system settings (i.e. administrator). You may
receive a warning message saying: "Invalid Display Settings:
The currently selected display resolution is invalid". Ignore
the instructions in this message and click or select "OK".
3. Open the 'START' menu by using the taskbar.
4. Highlight 'Settings' and open the Control Panel folder.
5. Select or double click on the 'Display' icon. The 'Display
Properties' window will pop up.
6. Select the 'Settings' tab from the 'Display Properties' window.
7. Select or click on the 'Display Type . . .' button. The
'Display Type' window will pop up.
8. Select or click on the 'Change' button. The 'Change Display'
window will pop up.
9. Select or click on the 'Have Disk' button. The 'Install From
Disk' window will pop up.
10. If you are installing from the Revolution(tm) 4 CD-ROM, change
the installation disk setting to the \WINNT40\ subdirectory on
the CD-ROM (i.e. if your CD-ROM is drive D:, then you should
type D:\WINNT40\ ). Select or click on the 'OK' button.
11. Select REV4.INF in the 'Locate File' window and click on
'Open' button.
12. Select 'OK" when the 'Install From Disk' window pops up.
13. A window will pop up indicating the name of the display driver
found. Select or click on the 'OK' button. A window will
then pop up asking if you wish to proceed to install the new
drivers. Select or click on the 'YES' button.
14. A pop up window will inform you that you have successfully
installed the drivers and that you must reboot in order for
the changes to take effect. Select or click on the 'OK'
button.
15. Close the 'Display Type' window and then the 'Display
Properties' window.
16. A 'Systems Settings Change' window will pop up and ask you if
you wish to restart your computer using the newly installed
drivers. Select or click on the 'YES' button to reboot your system.
17. The next time you boot, enter Windows NT 4.0 in normal mode - not
VGA Mode, and you will be using your new Revolution(tm) 4 card and
display driver.
18. After the system restarts, you will receive the following
message: 'Invalid Display Settings: A new graphics driver
has been installed. The default display resolution has been
temporarily used by the system. Use the Display Option in the
Windows NT Control Panel to select your preferred display
resolution'. Select or click 'OK'.
19. If the Display Settings Page is not visible, either open it by
selecting it through the taskbar or open it as detailed in
steps (3) through (6) above.
20. Select the desired resolution (desktop area), color depth
(palette), and refresh rate (frequency). Choose 'LIST ALL
MODES' to see a list of valid display modes or refer to the
'Supported Resolutions' section of this document for a list of
driver supported modes.
*NOTE* BE SURE TO TEST THE SELECTED MODE BEFORE RESTARTING
WINDOWS NT. IF YOUR MONITOR DOES NOT SUPPORT YOUR
CURRENT SELECTION, THE SYSTEM WILL RETURN WITH A BLANK
SCREEN AND MONITOR DAMAGE MAY RESULT. THE TEST WILL
ONLY SET THE MODE FOR 5 SECONDS AND RETURN TO ALLOW
YOU TO SELECT ANOTHER IF THE FIRST IS NOT SUPPORTED.
IF THE TEST BITMAP DISPLAYS PROPERLY, THE MONITOR IS
CAPABLE OF SUPPORTING THE SELECTED RESOLUTION AND
VERTICAL REFRESH RATE.
------------------------------------------------------------------
INSTALLING OR UPGRADING HAWKEYE IV UTILITY
------------------------------------------------------------------
NOTE!! After the display driver is installed, and the system
restarts, HawkEye IV can be installed. HawkEye IV can be
installed by running SETUP from the WINNT40 directory on the
Revolution IV CDROM, or the local/network directory that
contains the Revolution IV driver files.
*NOTE* RUNNING SETUP FORM THE WINNT40 DIRECTORY DOES NOT
INSTALL NEW DEVICE DISPLAY DRIVERS IT!! ONLY INSTALLS
THE HAWKEYE IV Control Panel.
------------------------------------------------------------------
SUPPORTED RESOLUTIONS
------------------------------------------------------------------
Revolution IV 16MB / 32MB
Windows NT 4.0 Desktop
Supported Resolutions for an Analog Monitor
Bit Depth Resolution Refresh Rates
8 640x480 60,72,75,85
800x600 60,72,75,85
1024x768 60,70,75,85
1152x864 60,70,75,85
1280x1024 60,75,85
1600x1200 60,70,75,80
1920x1080 60,72
1600x1024 76
16 640x480 60,72,75,85
800x600 60,72,75,85
1024x768 60,70,75,85
1152x864 60,70,75,85
1280x1024 60,75,85
1600x1200 60,70,75,80
1600x1024 76
1920x1080 60
32 640x480 60,72,75,85
800x600 60,72,75,85
1024x768 60,70,75,85
1152x864 60,70,75,85
1280x1024 60,75,85
1600x1200 60
1920x1080 60
Revolution IV 16MB / 32MB
Windows NT 4.0 Desktop
Supported Resolutions for the Digital Flat Panel
Bit Depth Resolution Refresh Rates
8 640x480 60
800x512 60
800x600 60
1024x768 60
1152x864 60
1280x1024 60
1600x1024 60
16 640x480 60
800x512 60
800x600 60
1024x768 60
1152x864 60
1280x1024 60
1600x1024 60
32 640x480 60
800x512 60
800x600 60
1024x768 60
1152x864 60
1280x1024 60
1600x1024 60
------------------------------------------------------------------
REVOLUTION IV SUPPORT FOR 3D
------------------------------------------------------------------
The NineICD implements the full functionality of OpenGL 1.1.
It also fully supports the Microsoft ICD (Installable Client Driver)
API. Industry standard libraries such as GLUT and WGL are also
supported. In fact, it is possible to write fully portable
windowed OpenGL applications that can be compiled and run under
multiple operating systems such as Windows and Unix, by using
GLUT.
Hardware acceleration for all Revolution IV boards works with or
without Display List Processor (DLP) support.
Hardware-accelerated OpenGL primitives include:
Gouraud-shaded and flat-shaded triangles
Triangle strips and triangle fans
Texture mapped and mipmapped triangles triangle strips and
triangle fans
Gouraud-shaded and flat-shaded lines
Polylines
Points, single and multiple sized.
In addition, hardware-accelerated Z-buffering, alpha-blending,
alpha-testing and fogging on all supported primitives. Mipmapped
triangle acceleration includes linear and bilinear minification.
------------------------------------------------------------------
PRESENT CAPABILITIES
------------------------------------------------------------------
The NineICD supports the OpenGL 1.1 standard as specified in
"The OpenGL Graphics System: A Specification (Version 1.1)"
by Mark Segal and Kurt Akeley, Chris Frazier Editor. This
document can be downloaded from the SGI web site (www.sgi.com).
The NineICD provides hardware accelerated OpenGL graphics
rendering that takes advantage of most hardware capabilities
of the Number Nine T2R4 chips. DLP and non-DLP operation are
supported. Switching between these modes is achieved by changing
an entry on the HawkEye Options page.
Note: Mode switching(changing resolutions and colors depths)
while an OpenGL application is open is not supported and
will cause unpredictable results.
------------------------------------------------------------------
SUPPORTED CONFIGURATIONS
------------------------------------------------------------------
The NineICD will work in 8, 16 or 32 bits/pixel, subject to video
memory size restrictions. OpenGL applications can either be run inside
a window on the desktop or in full screen mode.
If the application is running in software rendering mode, there
are no additional configuration requirements. If hardware
acceleration is being used, however, maximum window size supported
depends on available offscreen memory. The NineICD will
automatically revert to software rendering if not enough offscreen
memory is supported.
------------------------------------------------------------------
SOFTWARE UPGRADES
------------------------------------------------------------------
Even though you may have just received your Number Nine software,
newer versions may be available. Free upgrades are provided to
all Number Nine customers on the Number Nine World Wide Web home page
and FTP site.
To see if you have the latest version, compare the version number
of your software (on the label of the provided diskette or in
Status in the HawkEye IV Control Panel under Disk Version) with
the version number of the corresponding software on the World Wide Web
home page or FTP site.
------------------------------------------------------------------
USING THE NUMBER NINE BULLETIN BOARD SERVICE (BBS) - EUROPE ONLY
------------------------------------------------------------------
(EUROPEAN OFFICE)
Dial: +49 89 614 491 66
Baud Rates: Up to 14,400 baud
Compression: HST, v.32 and v.42 supported
Modem Setup: 8 data bits, 1 stop bit, no parity
Required: PKUNZIP 2.04g to decompress ZIP files
The BBS has a separate file area for each Number Nine product.
A complete listing of available files can be downloaded by invoking
the "Download List of Files" command from any file library menu.
Many files are self-extracting, but some files will require the
latest version of PKUNZIP to decompress. PKUNZIP is available
in the General library (filename PKZ204G.EXE), and can also be
found on most on-line services such as CompuServe and America
Online.
------------------------------------------------------------------
INTERNET
------------------------------------------------------------------
Number Nine driver updates are also available on our FTP site.
All current Number Nine drivers are available to anyone with
access to the Internet.
Our FTP Address is: ftp.nine.com.
Number Nine has a World Wide Web server at: http://www.nine.com
Product Registration can be completed on-line through the Number Nine
web server. Information about other Number Nine products, as well as
links to the FTP site can be accessed from our World Wide Web site.
------------------------------------------------------------------
KNOWN RESTRICTIONS AND PROBLEMS
------------------------------------------------------------------
The following restrictions apply:
. Some VGA modes may appear as slpit horizontal images when using
the Silicon Graphics 1600SW Digital Flat Panel Monitor. This
issue can be resolved by installing Windows NT Service Pack 4.
. The DrvShareLists ICD entry point is not operational. Programs
that use this functionality will not work and may crash the
system.
. There are some problems with visual quality at the detail level.
Artifacts and seams may be present in some texture-mapped
objects and scenes.
. It is not possible to dynamically switch resolutions or bit
depths while an OpenGL window is open.
. The ICD only supports software rendering at 8 bits/pixel.
. Applications or benchmarks that require the stencil buffer or
other OpenGL facilities not implemented in the T2R hardware
will run very slowly, and may show incorrect results. In
particular, programs HELLO2RTS and SHADOWFUN do not function
properly.
. Trilinear mipmap interpolation will not work when fogging or
alpha blending is also asked for. In these cases, the ICD falls
back to bilinear interpolation.
. Textured lines will come out colorless.
. Programs that use destination alpha will not display correctly
when running in 16bpp. Operation will be correct in 32
bits/pixel mode.
. Accessing the NT Task Manager while running a Full Screen OpenGL
application may cause crash the system.
. Opening a Full Screen DOS session with the NT Task Manager running
may cause a crash of the system.
. For optimal performance with 3D Studio MAX/SoftImage 3.8/ProEngineer 18-20
set your resolution and color depth to 1024x768x16Bpp or 1280x1024x16Bpp.
------------------------------------------------------------------
REMOVING HAWKEYE FOR WINDOWS NT
------------------------------------------------------------------
HawkEye IV includes an uninstall program that is available through
the Windows NT Control Panel Add/Remove Programs utility.
Note: You must be logged in as the user who installed HawkEye in
the first place for the uninstall to function properly.
To remove HawkEye IV from your system:
1. Click on the Windows NT 'Start' button
2. Select 'Settings' and then 'Control Panel'
3. Double click on the 'Add/Remove Programs' icon
4. Locate HawkEye NT on the list of software that can be removed
5. Either Double click on HawkEye NT or click once on it and then
click Add/Remove
6. The HawkEye NT Uninstall utility will then ask you to confirm
that you want to continue before it removes the files and
registry entries from your system.
If you do not have the Uninstall Program:
1. Right click on the Taskbar (to the right of the 'Start' button)
2. Go to Properties
3. Click on the 'Start Menu Programs' tab
4. Click on 'Remove'
5. From the list of applications, select HawkEye and click 'Remove'
6. From the same list, open the 'Start Up' list by clicking on the '+'
7. Click once on the HawkEye icon and click 'Remove'
8. Click 'Close'
9. Click 'OK'
------------------------------------------------------------------
OTHER PROBLEMS
------------------------------------------------------------------
Software sometimes does not perform consistently across all
resolutions and color depths. If you experience a persistent
problem for which you can not determine a cause or resolution, try
switching to a different resolution and/or color depth with
Resolution Exchange.
If the problem is consistent across resolutions, please consult
the application documentation. Most applications are distributed
with a "READ_ME" file that will contain important information
regarding potential application problems.
--------------------------------------------------------------------
PRODUCT REGISTRATION
--------------------------------------------------------------------
Product Registration can be completed on-line through the Number
Nine web site at
http://www.nine.com
--------------------------------------------------------------------
CONTACTING NUMBER NINE VISUAL TECHNOLOGY CORPORATION
--------------------------------------------------------------------
Hours of operation:
Corporate Offices: 8:30am to 5:30pm (Eastern Time)
Sales Offices: 8:00am to 7:00pm (Friday until 5:00pm) (Eastern Time)
Technical Support: 8:30am to 6:00pm (Friday until 5:00pm) (Eastern Time)
Corporate Offices: (781) 674-0009
Fax: (781) 869-7190
Sales Offices: 1 (800) GET-NINE (800-438-6463)
Sales Fax: (781) 869-7230
Technical Support: (781) 869-7214
Technical Support Fax: (781) 869-7222
* * *
European Sales:
Benelux:
Andre van Oort
Car Control Nederland bv
Alphenseweg 4f
5133 Riel
Netherlands
phone: +31 13 5186666
fax: +31 13 5186669
GSM: +31 6 53647753
e-mail: carco@carcontrol.nl
France:
Frederic Simard
Centre D`Activites de l`Ourcq
45, Rue Delizy
93692 Pantin
France
phone: +33 1 48 10 7550
fax: +33 1 48 10 7555
GSM: +33 609 478514
e-mail: 101352.1501@compuserve.com
Germany:
Number Nine Visual Technology GmbH
Inselkammerstr. 10
82008 Unterhaching
phone: +49 89 614 491 0
fax: +49 89 614 491 99
Italy:
Filippo Gargani
Via Ponte a Iozzi, 5
50020 Impruneta (FI)
Italy
phone: +39 55 208633
fax: +39 55 208455
GSM: +39 335 371522
e-mail: filippo@gargani.com
Scandinavia:
Thomas Stenberg
Aspbergsven 8
14590 Norsborg
Sweden
phone: +46 8 53028220
fax: +46 7 07559771
GSM: +46 707 552371
e-mail: thomas.stenberg@repit.se
UK:
Peter Cheang
Unit 8 Enterprise Centre
Cranbourne Road
Potters Bar, HERTS EN6 3DQ
UK
phone: +44 1707 855689
fax: +44 1707 855687
GSM: +44 410 179688
e-mail: dpcheang@aol.com
Far East Sales:
Japan:
DSS
Japan
phone: +81 45 476 7400
fax: +81 45 476 7401
e-mail: nb9support@diasemicon.co.jp
* * *
MAIL (USA)
NUMBER NINE VISUAL TECHNOLOGY
18 HARTWELL AVENUE
LEXINGTON, MA 02421-3141
USA
--------------------------------------------------------------------
TRADEMARKS
--------------------------------------------------------------------
The following terms are trademarks or registered trademarks of
Number Nine Visual Technology Corp. in the United States and/or
other countries:
Number Nine
#9
Revolution IV
HawkEye
The following terms are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries:
Microsoft
Windows NT
DirectX
DirectDraw
The following terms are trademarks or registered trademarks of
Silicon Graphics Incorporated in the United States and/or other countries:
OpenGL
--------------------------------------------------------------------
11-13-98 tm
Revolution IV v04.062.027
--------------------------------------------------------------------
(c) COPYRIGHT 1999, NUMBER NINE VISUAL TECHNOLOGY CORPORATION
All Rights Reserved.
--------------------------------------------------------------------