home *** CD-ROM | disk | FTP | other *** search
/ OS/2 Shareware BBS: Multimed / Multimed.zip / vidfmm5.zip / VIDHELP.HLP (.txt) < prev   
OS/2 Help File  |  1996-05-28  |  3KB  |  72 lines

  1.  
  2. ΓòÉΓòÉΓòÉ 1. Help for Selecting Number of Adapters ΓòÉΓòÉΓòÉ
  3.  
  4. Use this window to select the number of ///FAST Movie Line II Adapters that you 
  5. have installed in your system. The maximum number of Movie Line Adapters 
  6. supported by MMPM/2 is four. 
  7.  
  8. ///FAST Movie Line II Adapters are: 
  9.  
  10.      Movie Machine II. 
  11.      FPS 60. 
  12.      F60. 
  13.  
  14.  Note:   The OS/2 drivers were created by Kirchhoff & Grill Softwareentwicklung 
  15.  GmbH and are NOT supported by ///FAST Multimedia AG. 
  16.  
  17.  If you select zero, then you will de-install all Video Blaster Adapters that 
  18.  have been previously installed by MMPM/2. 
  19.  
  20.  
  21. ΓòÉΓòÉΓòÉ 2. Help for selecting Movie Line II values ΓòÉΓòÉΓòÉ
  22.  
  23. On this screen, you specify the values that you want to use with your Movie 
  24. Line II Adapter.  The values are described below. 
  25.  
  26. If you choose Close from the system menu, the selected values are set back to 
  27. the default values. 
  28.  
  29. Select Ok to save the selected values and continue. 
  30.  
  31. Base I/O Address 
  32.  
  33. This field allows you to select the base I/O address for all the Movie Line II 
  34. adapters you have installed in your system.  The base I/O address you select 
  35. for the Movie Line II adapters must be unique and should match the address you 
  36. selected prior to this installation. 
  37.  
  38. The valid base I/O addresses are: 
  39.  
  40.  318, 358 
  41.  
  42. If the device driver fails to initialize (during system reboot following 
  43. install), it might be necessary to change the base I/O address. To change the 
  44. base I/O address setting: 
  45.  
  46.       Perform a selective installation and select the new base I/O address, 
  47.  
  48.       or 
  49.  
  50.       Edit the CONFIG.SYS, specify the new base I/O address, and reboot. 
  51.  
  52.  Interrupt 
  53.  
  54.  This field allows you to select the interrupt for the Movie Line II adapters 
  55.  you have installed in your system.  The interrupt you select for the Movie 
  56.  Line II adapter must be unique and should match the interrupt you selected 
  57.  prior to this installation. 
  58.  
  59.  The valid interrupts are: 
  60.  
  61.   I10, I11, I12 and I15 
  62.  
  63.  If the device driver fails to initialize (during system reboot following 
  64.  install), it might be necessary to change the interrupt. To change the 
  65.  interrupt setting: 
  66.  
  67.       Perform a selective installation and select the new interrupt, 
  68.  
  69.       or 
  70.  
  71.       Edit the CONFIG.SYS, specify the new interrupt, and reboot. 
  72.