home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
ftp.tcs3.com
/
ftp.tcs3.com.tar
/
ftp.tcs3.com
/
DRIVERS
/
Network
/
LinkSYS
/
lne2000.exe
/
README
/
SCOUNIX.TXT
< prev
next >
Wrap
Text File
|
1996-02-01
|
8KB
|
209 lines
Linksys Ether16 LAN Card Software Setup Instructions
for SCO Unix
--------------------------------------------------------------------------
Copyright (C) 1994-1996 Linksys, All Rights Reserved
--------------------------------------------------------------------------
CONTENTS
--------------------------------------------------------------------------
Before You Begin
Novell NE2000 Compatibility
SCO Unix Setup
How to Get Technical Support
--------------------------------------------------------------------------
BEFORE YOU BEGIN
--------------------------------------------------------------------------
Before attempting to install the Ether16 LAN Card's network software
drivers, you should configure the card's internal settings with the
SETUP utility included on the Ether16 disk. To configure the card:
1. Get to the DOS command prompt (C:\>).
It is important that you have a "clean bootup" with no
network drivers loaded. If possible, bypass all of your
system's startup files and get to a DOS prompt.
If you are using Windows, close it down completely (select
File, then Exit from the Program Manager menu). Do NOT
run the Setup program from within a DOS window.
If you are using Windows 95, restart your PC. Hit the F8 key
when "Starting Windows 95..." appears on your screen. Select
"Command Prompt Only" from the menu that appears. When your
system continues booting again, press the F5 key to bypass all of
your startup files.
2. Insert the Ether16 disk into drive A: or B:. Then, from the
DOS prompt, type A:SETUP or B:SETUP and press the Enter key.
3. Select "Configure the Ether16 LAN Card Hardware" option from
the menu. Configure the card's I/O, IRQ, and connector type
settings (you can use the auto configure function if you want).
When you're finished, restart your computer and follow the
network software driver setup instructions shown below.
Important Note: When you configure the card's hardware, write
down the IRQ and I/O memory address that you use. You'll need
to make sure that your network software is configured so that
it uses these same values before your workstation will be able
to communicate with the network.
4. After the card has been set up, your PC will restart itself.
Connect your network cabling to the card and then run the
Setup program again. Run the Setup program's basic diagnostics
on the card to make sure that the hardware has been installed
correctly.
--------------------------------------------------------------------------
NOVELL NE2000 COMPATIBILITY
--------------------------------------------------------------------------
The Ether16 LAN Card is 100% Novell NE2000 compatible. If your network
software has a "generic" NE2000 adapter driver, run your network setup
software, select NOVELL NE2000 or a compatible driver from the list of
possible adapters and you're done--you won't need to follow the
instructions below.
To install the Ether16 LAN Card's own drivers (included on the Ether16
disk) -- which may provide better performance in some environments --
follow the instructions for your network software package below.
--------------------------------------------------------------------------
SCO Unix Setup
--------------------------------------------------------------------------
Login as a root user in maintenance mode.
Put the Ether16 disk into floppy A: or B: and use the doscp command to
copy the SCO UNIX driver into UNIX's directories:
# cd /
# doscp a:/scounix/setup /setup
(or # doscp b:/scounix/setup /setup)
# chmod +x /setup
# ./setup a:
(or # ./setup b:)
Run #netconfig
Available options:
1) Add a chain
2) Remove a chain
3) Reconfigure an element in a chain
4) Quit Select 1. Add a chain
Select top level of chain to Add or q to quit: 1. sco_tcp
(SCO TCP/IP for UNIX)
Select next level of chain to Add or q to quit: Select d22e
Ethernet Driver unit 0
Add chain sco_tcp->d22e0 (y/n): type 'y'
Enter number of media mode selection (0 1 2 3 4) [3] or 'q' to quit: n
Enter the internet Address of this interface n.n.n.n
Enter the netmask for this interface (default 255.255.255.0)
Does the interface use a broadcast address of all 1's (y/n) default : y
Enter the broadcast address for this interface default: n.n.n.n
Are these values correct ? (y/n) y
XX Pseudo ttys are currently configured, do you want to:
1) Add Pseudo ttys
2) Remove Pseudo ttys
Select an option or enter q to quit [q] q
Available options:
1) Add a chain
2) Remove a chain
3) Reconfigure a element in a chain
q. Quit Select option: q
Do you want to relink to kernel now ? y
Do you want this kernel to boot by default (y/n) y
Do you want the kernel environment rebuilt (y/n) y
Reboot unix
# shutdown -y -g0
------------------------------------------------------------------------
------------------------------------------------------------------------
HOW TO GET TECHNICAL SUPPORT
------------------------------------------------------------------------
There are a variety of methods that you can use to get FREE technical help
or sales information about Linksys products.
Voice & FAX
------------
The Linksys voice line is open during normal business hours, 7-5 p.m.,
Pacific Standard Time. The fax line is available 24 hours a day. When
sending a fax, be sure to include a detailed description of any
problem(s) that you are experiencing.
Technical Support Hotline (714) 261-1288
Fax (714) 261-8868
E-mail
------
To get technical or sales information bounced back to you from Linksys
automatically, send some e-mail to the address below. Include the
name of the product that you want help with, along with the word
HELP, in the subject line of your e-mail. Example: HELP ME WITH THIS
PRODUCT. (If requesting sales information, use the word SALES instead
of HELP).
E-mail Address info@linksys.com
Internet Access
---------------
You can also use your World Wide Web or FTP browser to visit Linksys on
the Internet.
Web Site http://www.linksys.com
FTP File Transfer Site ftp.linksys.com
Bulletin Board System (BBS)
---------------------------
To access the Linksys Bulletin Board System (BBS), set your modem to
8 bits, No parity, 1 stop bit, and call (714) 261-2888. Use a speed
setting of 33.6bps or slower. When downloading files, use the "Z-modem"
download protocol for best results.