home *** CD-ROM | disk | FTP | other *** search
/ ftp.whtech.com / ftp.whtech.com.tar / ftp.whtech.com / articles / archives / limanews.exe / XBINCON.TXT < prev    next >
Text File  |  2006-10-19  |  5KB  |  98 lines

  1. PUBLISHED IN LIMA NEWSLETTER OCTOBER 1987
  2.  
  3.  
  4.         INSTALLING EXTENDED BASIC INSIDE YOUR CONSOLE 
  5.  
  6.                       by John F. Willforth 
  7.                         West Penn 99'ers
  8.  
  9. (Ed. Note:  This article is reprinted from the July 87
  10. issue of the newsletter of the West Penn 99'er Club.  It
  11. has been our own experience that cleaning the console,
  12. particularly the cartridge port will usually solve problems
  13. encountered when using the XB module.  Instructions for
  14. doing this were publisned in the Jan 87 issue of Bits Bytes
  15. & Pixels.  It has also been our experience that a GRAM
  16. KRACKER with its gold plated contacts will often run
  17. extended basic reliably.) 
  18.  
  19.     For many of us there has been much frustation over the
  20. last several years about "HANG-UPS" that occur to the TI
  21. 99/4A using extended basic, just as the most critical part
  22. of a program or game is reached.   There are those who
  23. would lead you to believe that the power supply has been
  24. the cu;prit in the majority of the console locking in their
  25. club.  This may have been the problem experienced in the
  26. microcasm they are in.  I have experienced the problems
  27. with inconsistent and noisy D.C. voltages issued from the
  28. TI supplies also.  A few months ago I ran through 5
  29. straight VDP memory problems in a row, and could have made
  30. the statement that most if not all TI console problems will
  31. be found to have defective 4116 dynamic RAM chips.  This
  32. would have been absurd!  I'm making this statement only to
  33. try to reassure you that of all possible causes for console
  34. hangs, the GROM connection/cartridge connection is far and
  35. away the most common, and in particular the mating (or lack
  36. of) between the Extended Basic and Grom Connection, is the
  37. greatest culprit.  The purpose of this article is to assist
  38. those of you who would like to mive the Extended Basic
  39. module on board. 
  40. -----DO THE FOLLOWING AT YOUR OWN RISK! 
  41.  
  42. PARTS; * 1' ribbon cable (36 lead) or 2 lengths of 25 lead
  43.               cable. 
  44.        * 1 Extended Basic module (shell removed) 
  45.        * 1 double pole single throw slide switch (for
  46.               enabling/disabling Extended Basic) 
  47.        * Solder iron, wire cutters, etc. 
  48.  
  49.     I'm not going to get into the details for I feel if by
  50. now that you can't remove your own CPU from your console,
  51. you shouldn't be attempting this.  Get someone who can.
  52. remove the GROM Connector from the unit, and attach the
  53. ribbon cable to the pins of the rear of the circuit card
  54. that the GROM connector is attached.  Attach all but pins 4
  55. and 6 to ribbon cable.  4 and 6 are unused here.  Now,
  56. keeping the length of the wire to less than 8" attach the
  57. other ends of the corresponding wire to the Extended Basic
  58. card edge connector leads, remembering the relationship
  59. between the two.  i.e. pin 1 must go to pin 1, 2 to pin 2,
  60. and so on (not 4 or 6).  before you attempt any further
  61. modification to the machine, reassemble and see if Extended
  62. Basic comes up on the menu, and still functions, SIZE,
  63. ACCEPT AT, etc.  If you are still functional, continue. 
  64.  
  65.     Remove the 100 ohm resistor indicated, and cut the two
  66. traces where shown.  Now you may solder 4 equal lengths of
  67. wire to the switch (not longer than 10" in length).  Attach
  68. two of the wires across the cut in the trace (x) and the
  69. other two across (y), making sure that the pairs are on the
  70. same switch pole set.  Now, test the results again. 
  71.  
  72.     If the Extended Basic works when the switch is closed,
  73. and the cartridge slot will accept cartridges (meaning that
  74. a variety of GROM/ROM cartridges will function), when the
  75. switch is open, then you are almost home.  Mount the switch
  76. in a convenient location and insulate the bottom of the
  77. Extended Basic cartridge and locate the TOP RF SHIELD to
  78. the left of the GROM connection.  Reassemble.  It would
  79. also be of benifit to you at this time to install a reset
  80. button across pin 6 of the CPU chip and ground.  Trust me. 
  81.  
  82.     The reset switch will be particularly useful, in that
  83. you will now not be able to reset the machine by inserting
  84. the Extended Basic cartridge.  You may find that without
  85. the RESET switch, you will have to turn the console power
  86. switch off and then on to begin operation after switching
  87. from basic to Xbasic or other cartridges.  This is an easy
  88. option to install with a momentary contact switch across
  89. pin 6 on the CPU chip (TMS9900) and ground.  Reference the
  90. first drawing. 
  91.  
  92.     The second drawing is here to help you find the two
  93. traces that must be cut, and the 100 ohm resistor that must
  94. be removed.  The drawing of the switch on the right of the
  95. second drawing is to assist you in locating the switch
  96. properly to the circuit.  Attach wire pairs across the
  97. trace cuts.
  98.