home *** CD-ROM | disk | FTP | other *** search
- INSTRUCTIONS FOR EDITING THIS FILE
- ==========================================================
- DATA FILE FOR MCINSTAL.EXE PROGRAM
- This file is organized as follows:
-
- DESCRIPTION~DEVICE~EXTRA
-
- DESCRIPTION is the description which will appear on the
- screen during the MCINSTAL.EXE program.
-
- DEVICE is the device driver name which will be appENDed to
- ?:\MCADAM\DRIVERS and be inserted into the user config.sys file.
-
- EXTRA is applicable to printers/plotters and the mouse.
- In the case of printers/plotters EXTRA=exact mode command
- specification for the printer or plotter. If this information
- is left blank then MCINSTAL will ask the user for COM port
- information like baud rate, parity, data bits, and stop bits.
- In the case of mouse EXTRA=M for mouse or T for tablet,
- if it is blank M (mouse) is assumed.
- THE TILDEN (~) CHARACTER IS ABSOLUTELY NECESSARY.
- ==========================================================
- If you make changes, make sure the description field does
- not exceed 60 characters or the mcinstal.exe program
- will overflow during display.
- ==========================================================
- Comments can be entered but they must occur OUTSIDE the
- BEGIN/END sequence or they will appear in the device list,
- if they occur within the BEGIN/END sequence start them with
- the # character.
- ==========================================================
- DISPLAY
- BEGIN
- IBM EGA (Enhanced Graphics Adapter)~IBMEGA.SYS
- IBM VGA (Video Graphics Array)~IBMVGA12.SYS
- IBM PS/2 8514/A or XGA Graphics Adapter~IBMAFH.SYS
- Calcomp Drawing Board~CALDISPB.SYS
- Control Systems Artist 10/16~ART10CGI.SYS
- Control Systems Artist 10/16 MC~ARTISTMC.SYS
- Control Systems Artist XJ10~ARTXJ10.SYS
- Control Systems Artist XJ12~ART12CGI.SYS
- Metheus 1104~METHEUS.SYS
- NEC Graphics Engine~CGIDGIS.SYS
- Super VGA (800X600)~HRVGA.SYS
- Tseng 4000 Chip Set~ET4000.SYS
- Vermont Microsystems Cobra-1B3~IMVDI2.SYS
- Vermont Microsystems Cobra2/Plus~VMCGIS.SYS
- Vermont Microsystems Cobra Elite~VMCGISE.SYS
- Vermont Microsystems ImageManager 1024/8E~IMVDI2.SYS
- Video Seven VEGA VGA~IBMVGA12.SYS
- END
- #
- #
- #
- PRINTER
- BEGIN
- Epson FX/MX/RX80 Series~EPSON80.SYS~6,9600,N,8,1
- Epson FX/MX/RX100 Series~EPSON100.SYS~6,9600,N,8,1
- Epson LQ800/950/1000/2500/2550 Series~EPSONLQ.SYS~6,9600,N,8,1
- Epson EX800/1000, FX85/86e/185/286, LX800, MX80F/T~EPSONX.SYS~6,9600,N,8,1
- HP LaserJet Plus/Series II~LASERJET.SYS~2,9600,N,8,1
- IBM Proprinter II/XL~IBMPRO.SYS~6,9600,N,8,1
- Okidata Microline 84 & 93~OKID84.SYS~6,9600,N,8,1
- Okidata Microline 92~OKI92.SYS~6,9600,N,8,1
- Toshiba P351 & P1350~TOSHIBA.SYS~6,9600,N,8,1
- END
- #
- #
- #
- PLOTTER
- BEGIN
- Calcomp PCI Plotters~CCP.SYS~2,9600,N,8,1
- Computer Graphics Metafile (CGM) Generator~META.SYS~1,9600,N,8,1
- HP - 7440/7470A/7570/7580B/7585B/7586B/7595/7596~PLOTHP.SYS~2,9600,N,8,1
- IBM - 737X/6180/6184~PLOTHP.SYS~2,9600,N,8,1
- Zeta 8~ZETA8.SYS~2,9600,N,8,1
- HPGL HP Graphics Language File Generator~HPGL.SYS~1,9600,N,8,1
- HPGL2 HP Graphics Language/2 File Generator~HPGL2.SYS~1,9600,N,8,1
- Houston Instruments Plotters~HIDMPL.SYS~2,9600,N,8,1
- END
- #
- #
- #
- MOUSE
- BEGIN
- #
- #
- MSC PC Mouse (MouseSystems)~MSMOUSE.SYS~M
- IBM PS/2 Mouse~PS2MOUSE.SYS~M
- Microsoft Serial Mouse~MSMOUSE.SYS~M
- Microsoft Bus Mouse~MSMOUSE.SYS~M
- Summagraphics SummaSketch Plus MM1201 & MM961~SUMMATB.SYS~T
- Logitech Serial Mouse~MSMOUSE.SYS~M
- Calcomp DrawingBoard Series 2300~CALCOMPB.SYS~T
- END
-
- ==================================================================
- The following section (DRIVERS) should be used for names of special
- drivers within MICRO CADAM which do not have the extension .SYS.
- MCINSTAL will copy these drivers in the directory \MCADAM\DRIVERS
- when it copies all the .SYS drivers, and it will copy this driver
- into the C:\MCADAM directory for boot up purposes.
- DRIVERS
- BEGIN
- CGIPREP
- END
-
- ==========================================================
- The following section (DEFAULT) was added in Feb of 1988
- to support default options for all selections. The user
- can enter information about his system into MCINSTAL and
- using the following data, it will be remembered and when
- they bring it up later the information will be recalled
- from this data file using the following option.
- DO NOT EDIT THIS DATA. ONLY MCINSTAL.EXE SHOULD EDIT
- THIS INFORMATION. IF YOU CHANGE THE FOLLOWING LINES
- MCINSTAL.EXE MAY NOT WORK CORRECTLY.
- ==========================================================
- THIS SECTION MUST BE THE LAST IN THE FILE OR MCINSTAL
- WILL NOT RUN PROPERLY.
- ==========================================================
- DEFAULT
- BEGIN
- \AUTOEXEC.CAD
- \CONFIG.CAD
- \AUTOEXEC.OLD
- \CONFIG.OLD
- C:\MCADAM\
- \DOS
- N
- \PC3270
- 0
- ffff
- -1
- 7
- C:\MCADAM\DRIVERS\IBMVGA12.SYS
- 3
- C:\MCADAM\DRIVERS\MSMOUSE.SYS
- 050
- 000
- 000
- B
- M
- 5
- C:\MCADAM\DRIVERS\HPGL.SYS
- 7475
- METAFILE.DAT
- 1 9600 N 8 1
- -1
- D:\MCADAM\DRIVERS\LASERJET.SYS
- 6 9600 N 8 1
- IN
- 1
- 34X44
- N
- N
- 1
- C:
- C:\MCADAM\DRIVERS\
- END
-
-