home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Power-Programmierung
/
CD1.mdf
/
assemblr
/
library
/
sampler0
/
hiload.doc
< prev
next >
Wrap
Text File
|
1989-06-18
|
19KB
|
456 lines
HILOAD
An utility for loading TSR's someplace else
by
Larry Shannon
18 Jun 1989
HILOAD is a utility program designed to load your normal TSR
(Terminate-and-Stay-Resident) programs somewhere else in memory. Usually
this is a place outside the normal DOS region; that is, outside the
first 640K of system memory.
At this time, it does not include either extended or expanded memory.
BACKGROUND
The 8088 used in the PC-XT is capable of addressing up to 1024K of
memory. The designers of the PC and DOS decided that only the first
640K would be used by the operating system, DOS, and the rest was
reserved for other uses.
Because of the way the 8088 forms addresses, it is customary to refer to
addresses by a segment:offset combination. The 'actual' final address is
formed by multiplying the segment value by 16 (i.e., shifting it left 4
places) and adding the result to the offset address.
Thus, the very first address in the machine is called 0000:0000.
An address 1024 bytes from this start (hex 400) may be variously
indentified as 0000:0400, 0040:0000, 0020:0200, 0038:0080, etc.
For convenience, we may speak of the various segments as:
0000:0000 to 0000:FFFF Block 0
1000:0000 to 1000:FFFF Block 1
and so on
E000:0000 to E000:FFFF Block E
F000:0000 to F000:FFFF Block F
It is easy to see that there are 16 contiguous segments of 64K each,
yielding (16 X 64 =) 1024K, or one megabyte, and that DOS can only use
the first 10 segments, or blocks 0 through 9.
What is in the other 6 segments? Is that 384K of potential memory just
sitting there idle?
WHO'S USING WHAT?
Well, actually not. Some of these blocks have been set aside, and are
probably being used, for specific purposes.
Block F is where the ROM BIOS lives and, if you have a true- blue IBM
PC, where the ROM BASIC lives. So the F block is pretty well spoken
for.
Block B is where the memory for the video sits. If you have a
Monochrome Display Adapter (MDA), it uses 4K of memory at addresses
B000:0000 to B000:1000, and the remainder of the B block, 60K, is
unused. In fact, if you have a straight monochrome card like IBM
supplies, that's all the memory you have available.
If you have a Color Graphics Adapter (CGA), it occupies memory from
B800:0000 to B800:7FFF (or equivalently B000:8000 to B000:FFFF). Like
the MDA, when the CGA is in text mode it only uses the first 4K of this
memory, but it can support up to 8 'pages' of 4K each; when in graphics
mode, all 32K are in use. Like the MDA, true-blue CGA cards, and most
clone CGA cards, have only that 32K available.
Enhanced Graphics Adapters (EGA) are even bigger consumers of memory, at
maximum using the A block and part of the C block!
If you have a hard disk, its BIOS is normally located on the hard disk
controller card, and is ususlly resident at C000:8000, or as it is
commonly referred to, C800:0000.
SO WHAT?
Astute observers will notice that the D and E blocks were pretty much
left out of the above description. It is believed that these areas of
memory were set aside by IBM for program cartridges, but few, if any, of
these were actually produced, and this area is normally wide open and
available for use.
If you are like most PC users, you have only a monochrome or CGA
display, and the A block is available to you also.
DOWN TO BUSINESS
The '640K barrier' people talk about is caused by two reasons: programs
are getting more sophisticated and user-friendly, meaning they take up
more memory. Secondly, there has been a proliferation of many handy
programs that reside in memory (TSR's) which 'pop up' with useful
information at the touch of a key or perform some other action.
Examples are SideKick from Borland International, various printer
buffers which are almost a necessity, and so on. It is not too unusual
to have half one's DOS memory taken up with various TSR's.
While there's little we can do about fat programs, we can move these
TSR's out of the way. This was the driving force behind the development
of HILOAD.
WHERE DO I GET THIS MEMORY?
Some PC clone makers map their memory into the D and E blocks; Kaypro
for one does, others may also. Constructing a board to fill in these
holes is not difficult, especially if static RAMS (SRAM) are used; these
are now available in 32K X 8 sizes at attractive prices.
An old trick is to use commercial memory cards (now obsolete but
available) that allow themselves to be mapped into the desired regions.
Finally, users of Hercules Graphics cards and their clones usually have
the full 64K in the B block available, but only 4K is used in text mode.
That 60K looks mighty attractive, as does the 'spare' memory on a CGA
card...BUT...because one may easily forget there are programs in that
space, switching to Herc graphics, or simulating a CGA, or using a CGA
in graphics mode will really screw up the works, so this technique is
not recommended. It may be used to test out the program, though, and
see if it's worth the small trouble to get memory for the 'safe' areas.
HOW THE PROGRAM WORKS
HILOAD grabs the program you want, as well as any command tail required,
and loads it into the memory area you specify. After loading the
candidate TSR program, it revectors several DOS interrupts and then
executes the TSR program in the new location. When the TSR program
attempts to 'go resident', HILOAD traps that request, either from INT
27H or function 31H of INT 21H, resets the appropriate interrupt
vectors, examines the interrupt vector table to see which ones point to
the new program, and then terminates normally.
Thus, when HILOAD exits, zero DOS memory is used up, and the TSR is
snugly nestled in another part of memory, acting just like it normally
does.
HOW TO SPECIFY VARIOUS THINGS
HILOAD requires various pieces of information to operate properly.
Addresses - HILOAD requires a starting address for
placing TSR's. After it places the first
one, it keeps track of where it should place
the next one by using the Intra-application
Communication Area (ICA) at 0040:00F0
through 0040:00FF. It checks this area and
computes an address from the information
there, so the initial starting address has
to be specified only once (until you change
blocks). As long as the loading area is
contiguous, the starting address need not be
re-specified.
The starting address is specified by an en-
vironment variable, which is discussed be-
low.
Program names - The program name to be loaded must be
specified with the full path name. Sorry
about this, but it wasn't worth the effort
to program the logic to chase down the paths
to find the programs. This is not consid-
dered (by me, anyhow) to be a serious ob-
jection, as the typical use of this program
is in your AUTOEXEC file where it is only
typed in once.
Starting off - Executing HILOAD without any program
specified causes it to zero out the ICA.
This is the easiest way to begin a loading
sequence after changing the start address.
SPECIFYING A START ADDRESS (ENVIRONMENT VARIABLES)
When DOS loads a program, it also provides that program with a copy of
what it calls the Environment. To see what the contents of your
environment are, do the following:
At the DOS prompt (e.g., C:\>), type SET <CR>
The response will be a list of things, starting with COMSPEC and
continuing with your PATH and PROMPT values (if you have any). After
these values, you may or may not have additional entries. If you do,
they will be of the form:
name=value
To add a value to the environment, type:
set abc=ABCabc <CR>
and then type
set <CR>
Notice that a new environment variable has been added. Notice also that
the name, abc, has been capitalized as ABC, but the value remains as it
was typed in, i.e., ABCabc.
To change an environment value, type
set name=NewValue<CR>
and NewValue will replace the old value.
To delete an environment variable, type
set name=<CR>
and the value will disappear from the environment.
HILOAD requires an environment variable with a name the same as the
program name. The value is the hex starting address.
So, if the program is named HILOAD, as it is on this disk, and the
desired starting value is A000, then you would set the environment
variable by typing:
set hiload=A000<CR>
This can also be done as an entry in your AUTOEXEC.BAT file.
DOS is poorly documented, but it provides the name of the program it
loads, and where it came from, right after the environment. I have used
this quirk of DOS to determine the name of the environment variable. If
you change the program name to, say, SHIFTSR.COM, then you would set the
environment variable as:
set shiftsr=A000<CR>
This feature (?) allows you to have multiple copies of the program under
different names, each with its own environment variable, if you should
so desire.
NOTE: As far as I can tell, this feature is only available in DOS 3.X.
The program determines the DOS version in use and, if less than 3.0, it
uses a default program name of HILOAD. This is what the name of the
environment variable would have to be, no matter what you rename the
program to.
INITIALIZING THE PROCESS
As stated above, the program must first initialize the ICA. It does this
by being invoked with no parameters. The 'standard' starting sequence
is therefore:
SET HILOAD=A000
HILOAD
etc.
SPECIFYING PROGRAMS TO LOAD
Also as stated above, full path names must be given. Suppose you have
four TSR's you wish to load, as follows:
NAME SIZE PARAMETERS (TSR command tail)
TSR1 14K none
TSR2 22K /X /U /M=22
TSR3 1.4K none
TSR4 26K 'text string'
Adding them up, we see that they will occupy less than 64K, so they can
all be loaded in one block. Suppose also we have the A block available
for use. The series of commands in the AUTOEXEC file to perform the
desired action might be:
SET HILOAD=A000 starting address
HILOAD initialize
HILOAD \DOS\TSR1 load first tsr
HILOAD \SUB1\SUB2\TSR2 /X /U /M=22 load next tsr
HILOAD \TSR3 load next tsr
HILOAD \UTILITY\TSR4 'text string' load last tsr
The directories shown are the complete path names
to the various TSR's.
Suppose now you have another TSR you want loaded, but it's too big to
fit in the A block; you have memory available in D block.
You would follow the above sequence with:
SET HILOAD=D000 reset start address
HILOAD re-initialize
HILOAD \SUB3\SUB4\TSR5 load it
PROGRAM OUTPUT
HILOAD issues various progress and error messages as it chugs along. It
tells you the starting address it uses, the name of the program it is
loading, what it found for a command tail to the TSR, and the amount of
memory the TSR has reserved for itself.
It also lists the interrupts the TSR has captured, along with their new
addresses. This can be handy for debugging purposes or just finding out
who captures what. Many TSRs do not go through Int 21H functions 35H and
25H to get and set the interrupt vectors; they directly manipulate the
DOS interrupt table at the bottom of memory. This is not a recommended
technique but many do so. HILOAD will capture these villians (SideKick
being the most prominent one) and show what they trap.
Incidentally, it appears that SideKick traps interrupt 21H for itself,
and any TSR loaded after it, who attempts to grab Int 9H, is pushed down
the list by SideKick so he (SideKick) still has first grab at the
keyboard. Very clever programming; a pain in the kazoo when you're
groping around to figure out what's actually happening!
The above comments are based on an older version of SideKick (1.56)
which I have been using. Later versions may act in a more civilized
manner.
KEEPING THE OUTPUT
Since the information from HILOAD can whiz off the screen before you
have a chance to read it, it is a good idea to redirect the output to a
file instead of the screen. The program output can then be perused at
your leisure. The following sequence is an example of how to do this:
DEL TSRLIST.LST delete old file
SET HILOAD=A000 set start address
HILOAD >>TSRLST.LST initialize
HILOAD \TSR1 >>TSRLST.LST load first tsr
HILOAD \SUB1\TSR2 /X /Z >>TSRLST.LST load next tsr
SET HILOAD=D000 reset start address
HILOAD >>TSRLST.LST initialize
HILOAD \UTILITY\BIGTSR /PARMS >>TSRLST.LST load big tsr
After everything is loaded, the file TSRLST.LST may be browsed to see
what went on, get addresses, check vectors, etc.
Of course, the output may also be redirected to the printer by putting a
>PRN instead of >>filename.ext
ERROR MESSAGES
If something doesn't go right, the program tries to tell you and exit
safely. The error messages are:
No address given ... ABORTING Something's wrong with the
environment variable. Check
spelling of variable name and
make sure it agrees with the
program name.
The value given must be 4 hex
digits, upper or lower case.
Can't find file PROGNAME ... ABORTING HILOAD was unable to locate
the specified program. Check to
see that the path is correct.
Also, only .COM files can be
loaded this way; .EXE files
will bomb!
Requires DOS 2.0 ... ABORTING Program requires DOS version
2.0 or above.
The program also issues a message when it initializes the ICA.
DISCLAIMER
TSRs are tricky things; SideKick is notorious for being sensitive to the
order in which other TSR's are loaded. Experiment with loading your TSRs
in the 'normal' fashion until you get a loading sequence that works. Use
that order to HILOAD them and all should be well.
LEGAL STUFF
This program is being placed in the public domain. It may be copied and
distributed freely for non-commercial uses. Both this file and the
executable code must be distributed together and unmodified.
Any brand names mentioned are copyright by their respective owners.
SHEEPISH ADMISSION
This program was developed over a period of time as I was learning about
TSRs and revectoring interrupts, etc. Also, though the objective of the
program remained firm, the little niggly details kept changing on me as
I thought of alternate ways to accomplish things and more frills were
added.
Consequently, the source code is comprehensible to me but I'm sure looks
like a real mess to the 'seasoned professional'. I am thus a little
ashamed to release it for public scrutiny and scorn.
However, it is included and commented as best as I can recall what each
little piece does. Don't bother to tell me there are 'dead code' areas
and unused variables.
Anybody who wants can modify it to their hearts' content, but please
take note of the distributon restriction noted above.
Larry Shannon
5615 Truscott Terrace
Lakeview, NY 14085
- end -
----------------end-of-author's-documentation---------------
Software Library Information:
This disk copy provided as a service of
The Public (Software) Library
We are not the authors of this program, nor are we associated
with the author in any way other than as a distributor of the
program in accordance with the author's terms of distribution.
Please direct shareware payments and specific questions about
this program to the author of the program, whose name appears
elsewhere in this documentation. If you have trouble getting
in touch with the author, we will do whatever we can to help
you with your questions. All programs have been tested and do
run. To report problems, please use the form that is in the
file PROBLEM.DOC on many of our disks or in other written for-
mat with screen printouts, if possible. The P(s)L cannot de-
bug programs over the telephone.
Disks in the P(s)L are updated monthly, so if you did not get
this disk directly from the P(s)L, you should be aware that
the files in this set may no longer be the current versions.
For a copy of the latest monthly software library newsletter
and a list of the 2,000+ disks in the library, call or write
The Public (Software) Library
P.O.Box 35705 - F
Houston, TX 77235-5705
Orders: 800-2424-PSL
Info: 713-524-6394
FAX #: 713-524-6398
CIS ID: 71355,470