Spec Disk 1998 Spring 4.0/Spec Disk 1998 Spring 4.0.iso/text/07710mrp.txt

Text File | 1998-06-10 | 32.5 KB | 757 lines

                         SECTION 07710

                 MANUFACTURED ROOF SPECIALTIES

NOTE ** This section is based on products manufactured by
        Marathon Roofing Products Inc., which is located at
        the following address:
NOTE **     367 Nagel Drive
NOTE **     Buffalo NY 14225-4732
NOTE **     Tel:  [phone]
NOTE **     Tel:  [phone]
NOTE **     Fax:  [phone]
NOTE **     Website:  http://www.marathondrains.com
NOTE **     E-mail:  [e-mail]
NOTE **
NOTE ** Marathon manufactures a complete line of roof
        drains and breather vents for new roofing,
        reroofing, and retrofit applications.  Drain
        materials include copper, PVC, ABS, aluminum, and
        epoxy-coated cast iron.  Vent materials include
        aluminum, copper, high-density polyethylene, and
        PVC.  Custom products may be fabricated to suit
        almost any project condition, with factory
        assistance.
NOTE **
NOTE ** The section includes proprietary provisions for all
        types and styles of roof drains and breather vents,
        and must be edited to delete products and related
        provisions not required for a particular project.
NOTE **
NOTE ** SECTION 07710 - MANUFACTURED ROOF SPECIALTIES,
        Copyright 1998, The Architect's Catalog, Inc.


PART 1  GENERAL

1.1 SECTION INCLUDES
NOTE ** Delete items below not required for project.

    A.  Roof drains for new roofing.

    B.  Roof drains for reroofing.

    C.  Roof drains for retrofitting into existing roof drains.

    D.  Roof vents and breathers.

    E.  Soil vent stack flashings.

1.2 RELATED SECTIONS
NOTE ** Delete any sections below not relevant to this
        project;  add others as required.

    A.  Section 07500 - Membrane Roofing.

    B.  Section 07510 - Built-Up Bituminous Roofing.

    C.  Section 07530 - Elastomeric Membrane Roofing.

    D.  Section 07550 - Modified Bituminous Membrane Roofing.

    E.  Section 07590 - Roof Maintenance and Repairs.

    F.  Section 15150 - Sanitary Waste and Vent Piping.

    G.  Section 15160 - Storm Drainage Piping.

1.3 SUBMITTALS

    A.  Submit under provisions of Section 01300.

    B.  Product Data:  Provide manufacturer's standard details
        and installation instructions.

1.4 PROJECT CONDITIONS

    A.  Obtain Material Safety Data Sheets (MSDS) from
        manufacturer if required.


PART 2  PRODUCTS

2.1 MANUFACTURER

    A.  Provide prefabricated roof specialties fabricated by
        Marathon Roofing Products, Inc: 367 Nagel Drive, Buffalo
        NY 14225-4732; ASD.  Tel: [phone] or (800) 828-
        8424; Fax: [phone].

    B.  Substitutions:  Not permitted.
NOTE ** Delete the following article if drains for new
        construction are not required.

2.2 FLANGE/PIPE DRAINS

    A.  Marathon Premium Century Series Roof Drains:
NOTE ** Select straight or funnel profile, as desired.
NOTE **
NOTE ** Straight profile with clamping ring (optional) is
        used when water cut off mastic is required and a
        greater clamping surface is needed by membrane
        manufacturer.
NOTE **
NOTE ** For EPDM or CSPE membranes, straight profile is
        recommended with clamping ring.
NOTE **
NOTE ** Delete profiles not required.
        1.  Straight profile, solid copper construction.
        2.  Straight profile, solid copper construction, with
            clamping ring.
        3.  Funnel profile, solid copper construction.
NOTE ** Select uncoated flange for EPDM and CSPE membranes,
        primed flange for BUR and mod. bit. membranes, PVC-
        coated flange for PVC and CPE membranes.  Delete
        two of the three coating options, below.
        4.  18-inch (457 mm) diameter flange, 20 ounces per
            square foot (61 kg/sq m) copper.
            a.  Uncoated.
            b.  Primed for adhesion to asphaltic membranes.
            c.  PVC-coated, for heat welded membrane attachment.
        5.  Perforated copper gravel ring.
NOTE ** HDPE strainer is standard, aluminum is optional.
        Delete one of the two materials, below.
        6.  Strainer:  10-inch (254 mm) diameter, bolted down.
            a.  High density polyethylene.
            b.  Cast aluminum alloy.
NOTE ** Select applicable connection types.  Delete those
        not required.  All types are available in 2, 3, and
        4 inch sizes.  Plain and Fernco connections are
        also available in 6 inch size.
        7.  Connections:  Pipe size as indicated on the drawings.
            a.  Plain, 9-inch (228 mm) depth.
            b.  Plain, 15-inch (381 mm) depth.
            c.  Expansion coupler (Fernco) with stainless steel
                compression clamps; vertical or 90 degree outlet
                to suit project conditions, or as indicated.
            d.  PVC hub (Conectite) fitting, vertical outlet only
                to suit project conditions, or as indicated.

    B.  Marathon Economy Century Series Roof Drains:
        1.  Straight profile, solid copper construction.
NOTE ** Select primed flange for BUR and mod. bit.
        membranes, PVC-coated flange for PVC and CPE
        membranes.  (For EPDM and CSPE membranes, see
        Century Premium Series drains, below.)  Delete one
        of the two coating options, below.
        2.  14-inch (355 mm) diameter flange, 16 ounces per
            square foot (48.8 kg/sq m) copper.
            a.  Primed for adhesion to asphaltic membranes.
            b.  PVC-coated, for heat welded membrane attachment.
        3.  Perforated copper gravel ring.
NOTE ** HDPE strainer is standard, aluminum is optional.
        Delete one of the two materials, below.
        4.  Strainer:  5-inch (127 mm) diameter.
            a.  High density polyethylene.
            b.  Cast aluminum alloy.
NOTE ** Select applicable connection types.  Delete those
        not required.  All types are available in 2, 3, and
        4 inch sizes.
        5.  Connections:  Match pipe size O.D. as indicated on
            the drawings.
            a.  Plain, 9-inch (228 mm) depth.
            b.  Plain, 15-inch (381 mm) depth.
            c.  Expansion coupler (Fernco) with stainless steel
                compression clamps; vertical or 90 degree outlet
                to suit project conditions, or as indicated.
            d.  PVC hub (Conectite) fitting, vertical outlet to
                suit project conditions, or as indicated.
NOTE ** Delete the following article if drains for
        retrofitting into existing drain bodies are not
        required.  Diamond Series copper roof drains are
        appropriate to retrofit existing drains without
        removing existing drain or piping.  These drains
        are simply and economically installed using rubber
        sealant and O-rings to create a friction fit.
        Where a mechanical seal is required, see
        "PROLINER", a flange/expansion-sleeve or
        flange/mechanical-seal drain, below.  See also
        "COPPER-TITE," a sealed in-place retrofit drain.

2.3 FLANGE/INSERT RETROFIT DRAINS

    A.  Marathon Diamond (75) Series Roof Drains:
NOTE ** Select straight or funnel profile, as desired.
        Drain styles older than 1950 typically accept only
        straight profile.
NOTE **
NOTE ** Straight profile with clamping ring is used when
        water cut off mastic is required and a greater
        clamping surface is needed by membrane
        manufacturer.
NOTE **
NOTE ** For EPDM or CSPE membranes, straight profile is
        recommended with clamping ring.
NOTE **
NOTE ** Delete profiles not required.
        1.  Straight profile, solid copper construction.  Flange:
            14-inch (355 mm) diameter flange, 16 ounces per
            square foot (48.8 kg/sq m) copper for 2-inch (50 mm)
            through 4-inch (101 mm) drain sizes;  18-inch (457
            mm) diameter flange, 20 ounces per square foot (61
            kg/sq m) copper for 5-inch (127 mm) and 6-inch drain
            sizes.
        2.  Straight profile, solid copper construction, with
            bolted down clamping ring.  Flange:  14-inch (355 mm)
            diameter flange, 16 ounces per square foot (48.8
            kg/sq m) copper for 2-inch (50 mm) through 4-inch
            (101 mm) drain sizes;  18-inch (457 mm) diameter
            flange, 20 ounces per square foot (61 kg/sq m) copper
            for 5-inch (127 mm) and 6-inch (152 mm) drain sizes.
        3.  Straight profile, solid copper construction, with
            clamping ring.  Flange:  14-inch (355 mm) diameter
            flange, 16 ounces per square foot (48.8 kg/sq m)
            copper for 2-inch (50 mm) through 4-inch (101 mm)
            drain sizes;  18-inch (457 mm) diameter flange, 20
            ounces per square foot (61 kg/sq m) copper for 5-inch
            (127 mm) and 6-inch (152 mm) drain sizes.
        4.  Funnel profile, solid copper construction.  Flange:
            18-inch (457 mm) diameter flange, 20 ounces per
            square foot (61 kg/sq m) copper.
NOTE ** Select uncoated flange for EPDM membranes, primed
        flange for BUR and modified bitumen membranes, PVC-
        coated flange for PVC and CPE membranes.  Delete
        two of the three coating options, below.
        5.  Flange coating:
            a.  Uncoated.
            b.  Primed for adhesion to asphaltic membranes.
            c.  PVC-coated, for heat welded membrane attachment.
        6.  Perforated copper gravel ring.
        7.  Strainer:
NOTE ** Delete inapplicable strainer sizes, below.
            a.  5-inch (127 mm) diameter for straight profile 2-
                inch (50 mm) through 4-inch (101 mm) drain sizes.
            b.  10-inch (254 mm) diameter for straight profile 5-
                inch (127 mm) and 6-inch (152 mm) drain sizes.
            c.  10-inch (254 mm) diameter for funnel profile
                drains.
NOTE ** HDPE strainer is standard, aluminum is optional.
        Delete one of the two materials, below.
            d.  High density polyethylene.
            e.  Cast aluminum alloy.
NOTE ** Select applicable connection types.  Delete those
        not required.  Straight profile drains are
        available in  9 and 15-inch depths.  Funnel profile
        drains are available in 12 and 18-inch depths.  All
        types are available in 2, 3, 4, 5, and 6 inch
        sizes, and larger sizes upon request.
        8.  Connections:  Pipe size as indicated on the drawings;
            diameter sized to slip inside of existing drain
            piping.
            a.  Plain, 9-inch (228 mm) depth.
            b.  Plain, 15-inch (381 mm) depth.
            c.  Plain, 12-inch (304 mm) depth.
            d.  Plain, 18-inch (457 mm) depth.
NOTE ** Delete the following article if drains for
        retrofitting into existing drain bodies are not
        required.  PROLINER Series roof drains with copper
        flange and malleable metal outlets are appropriate
        to retrofit existing drains without removing
        existing drain or piping, where a permanent
        mechanical seal between the new drain and the
        existing piping is required. The PROLINER tool is
        used to mechanically lock the PROLINER drain in
        place.

2.4 FLANGE/EXPANSION-SLEEVE RETROFIT DRAINS

    A.  Marathon PROLINER Series.
NOTE ** Select straight or funnel profile, as desired.
        Drain styles older than 1950 typically accept only
        straight profile.
NOTE **
NOTE ** Straight profile with clamping ring is used when
        water cut off mastic is required and a greater
        clamping surface is needed by membrane
        manufacturer.
NOTE **
NOTE ** For EPDM or CSPE membranes, straight profile is
        recommended with clamping ring.
NOTE **
NOTE ** Delete profiles not required.
        1.  Straight profile.
        2.  Straight profile, with clamping ring.
        3.  Funnel profile.
NOTE ** Select uncoated flange for EPDM membranes, primed
        flange for BUR and modified bitumen membranes, PVC-
        coated flange for PVC and CPE membranes.  Delete
        two of the three coating options, below.
        4.  Flange:  18-inch (457 mm) diameter flange, 20 ounces
            per square foot (61 kg/sq m) copper.
            a.  Uncoated.
            b.  Primed for adhesion to asphaltic membranes.
            c.  PVC-coated, for heat welded membrane attachment.
        5.  Perforated copper gravel ring.
NOTE ** HDPE strainer is standard, aluminum is optional.
        Delete one of the two materials, below.
        6.  Strainer:  10-inch (254 mm) diameter.
            a.  High density polyethylene.
            b.  Cast aluminum alloy.
NOTE ** Outlets are available to retrofit standard 3, 4, 5,
        and 6-inch sizes and other non-standard sizes.
        7.  Outlet:  Malleable metal alloy.  Pipe size as
            indicated on the drawings;  diameter sized to slip
            inside of existing drain piping, with 1/4-inch (6 mm)
            maximum difference between existing pipe I.D. and
            outlet O.D.
NOTE ** Delete the following article if drains for
        retrofitting into existing drain bodies are not
        required.  ProSeal Series roof drains with copper
        flange and mechanical compression seal are
        appropriate to retrofit existing drains without
        removing existing drain or piping, where a
        permanent mechanical seal between the new drain and
        the existing piping is required.

2.5 FLANGE/MECHANICAL-SEAL RETROFIT DRAINS

    A.  Marathon Copper-Tite Series Roof Drains:
NOTE ** Select straight or funnel profile, as desired.
        Drain styles older than 1950 typically accept only
        straight profile.
NOTE **
NOTE ** Straight profile with clamping ring is used when
        water cut off mastic is required and a greater
        clamping surface is needed by membrane
        manufacturer.
NOTE **
NOTE ** For EPDM or CSPE membranes, straight profile is
        recommended with clamping ring.
NOTE **
NOTE ** Delete profiles not required.
        1.  Straight (CTS) profile.
        2.  Straight profile with clamping ring.
        3.  Funnel (CTF) profile.
NOTE ** Select plain flange for EPDM membranes, primed
        flange for BUR and modified bitumen membranes, PVC-
        coated flange for PVC and CPE membranes.  Delete
        two of the three finish options, below.
        4.  Flange:  20 ounces per square foot (61 kg/sq m)
            copper.
            a.  Plain finish
            b.  Asphalt primed finish.
            c.  PVC-coated finish.
NOTE ** Flange size is 14 inches (356 mm) in diameter for
        2, 3, and 4-inch (51, 76, and 102 mm) straight
        (CTS) drains, 18 inches (457 mm) in diameter for
        all others.  Delete one of the two sizes, below.
        5.  Flange size:  14 inches (356 mm).
        6.  Flange size:  18 inches (457 mm).
NOTE ** Plastic strainer is standard, aluminum is optional.
        Delete one of the two materials, below.
        7.  Strainer:  Plastic.
        8.  Strainer:  Aluminum.
NOTE ** For straight (CTS) drains, 9-inch (229 mm) long
        outlets are available to retrofit standard 2, 3, 4,
        5, 6, and 8-inch (51, 76, 102, 127, 152, and 203
        mm) drain pipes; drain outlets may be ordered
        extended by 6 inches (152 mm).
NOTE **
NOTE ** For straight drains with clamping ring, 9-inch (229
        mm) long outlets are available to retrofit standard
        2, 3, 4, 5, and 6-inch (51, 76, 102, 127, and 152
        mm) drain pipes; drain outlets may be ordered
        extended by 6 inches (152 mm).
NOTE **
NOTE ** For funnel (CTF) drains, 12-inch (305 mm) long
        outlets are available to retrofit standard 2, 3, 4,
        5, and 6-inch (51, 76, 102, 127, and 152 mm) drain
        pipes; drain outlets may be ordered extended by 6
        inches (152 mm).
        9.  Outlet:  Copper outlet with 2-inch (51 mm) wide
            asphalt-impregnated high density expanding foam
            compression seal.  Pipe size as indicated on the
            drawings; diameter sized to slip inside of existing
            drain piping, with 1/4-inch (6 mm) maximum difference
            between existing pipe I.D. and outlet O.D.

    B.  Marathon ProSeal Series Roof Drains:
NOTE ** Select straight or funnel profile, as desired.
        Drain styles older than 1950 typically accept only
        straight profile.
NOTE **
NOTE ** Straight profile with clamping ring is used when
        water cut off mastic is required and a greater
        clamping surface is needed by membrane
        manufacturer.
NOTE **
NOTE ** For EPDM or CSPE membranes, straight profile is
        recommended with clamping ring.
NOTE **
NOTE ** Delete profiles not required.
        1.  Straight profile.
        2.  Straight profile,  with clamping ring.
        3.  Funnel profile.
NOTE ** Select uncoated flange for EPDM membranes, primed
        flange for BUR and modified bitumen membranes, PVC-
        coated flange for PVC and CPE membranes.  Delete
        two of the three coating options, below.
        4.  Flange:  18-inch (457 mm) diameter flange, 20 ounces
            per square foot (61 kg/sq m) copper.
            a.  Uncoated.
            b.  Primed for adhesion to asphaltic membranes.
            c.  PVC-coated, for heat welded membrane attachment.
        5.  Perforated copper gravel ring.
NOTE ** HDPE strainer is standard, aluminum is optional.
        Delete one of the two materials, below.
        6.  Strainer:  10-inch (254 mm) diameter.
            a.  High density polyethylene.
            b.  Cast aluminum alloy.
NOTE ** Outlets are available to retrofit standard 3, 4, 5,
        and 6-inch sizes.
        7.  Outlet:  Copper outlet with elastomeric mechanical
            compression seal.  Pipe size as indicated on the
            drawings;  diameter sized to slip inside of existing
            drain piping, with 1/4-inch (6 mm) maximum difference
            between existing pipe I.D. and outlet O.D.
NOTE ** Delete the following article if mechanical drains
        are not required.
NOTE ** ULRD drains (PVC or ABS body), RD-1 and RD-10
        drains (epoxy-coated cast iron body) are suitable
        for most single ply and conventional built-up
        roofing membranes and with roof decks of steel,
        wood, precast concrete, and gypsum.
2.6 MECHANICAL DRAINS
NOTE ** Select either PVC, ABS, or epoxy-coated cast iron
        drain body.  Delete inapplicable paragraphs, below.

    A.  Marathon ULRD (Utility Large Roof Drain):  Injection
        molded PVC drain body with solvent-weld style outlet.

    B.  Marathon ULRD (Utility Large Roof Drain):  Injection
        molded ABS drain body with solvent-weld style outlet.

    C.  Marathon RD-1:  Epoxy-coated standard size cast iron
        drain body with no-hub style outlet.

    D.  Marathon RD-10:  Epoxy-coated large size cast iron drain
        body with no-hub style outlet.
    E.  Construction:
NOTE ** Select either polyethylene or metal strainer,
        below.  Delete any other construction features that
        are not required.
        1.  Strainer:  Molded polyethylene dome.
        2.  Strainer:  Epoxy-coated metal dome.
        3.  Clamping ring:  Epoxy-coated aluminum.
        4.  Underdeck clamp:  Aluminum
        5.  Adjustable insulation extension flange:  Match
            insulation thickness.
        6.  Bearing pan.
        7.  Waterproofing flange.
        8.  Flow-control device.
        9.  Flexible expansion coupling with stainless steel band
            clamps.
NOTE ** PVC and ABS drains are available in 3, 4, and 6-
        inch sizes.  Cast iron drains are available in 3,
        4, 6, and 8-inch sizes.

    F.  Pipe size as indicated on the drawings.
NOTE ** Delete the following article if parapet/scupper
        drains are not required.

2.7 PARAPET SCUPPER DRAINS

    A.  Marathon RD-27.

    B.  Construction:
        1.  Cast aluminum grate, body, and outlet.
        2.  Reversible hub connection for 45 or 90-degree outlet.
NOTE ** Select either angled grate (standard) or flat grate
        (optional).
        3.  Angled grate.
        4.  Flat grate.
NOTE ** Select either red epoxy paint finish (standard) or
        nickel bronze finish.
        5.  Red epoxy finish.
        6.  Nickel bronze finish.
NOTE ** Delete the following article if roof vents are not
        required.

2.8 ROOF VENTS AND BREATHERS
NOTE ** Select type of vents desired from paragraphs below.
        Delete those that are not required.
NOTE **
NOTE ** Vents are designed to assist in relieving pressure
        created by moisture in lightweight insulating
        concrete materials, and for venting conventional
        roofing insulation.

    A.  Solar Powered Roof Vent:  Marathon Sol-A-Vent; continuous-
        operation exhaust fan powered by 4 inch (100 mm) diameter
        photoelectric cell and battery.
        1.  Battery:  Rechargeable NiCad battery charged by cell
            capable of powering fan for 3 overcast days and
            nights.
        2.  Minimum capacity:  900 cubic feet (25 cu m) per hour.
        3.  Housing:  Aluminum; flanged for flashing into
            roofing, adjustable pitch to adapt to sloped roofs.
NOTE ** Delete one of the following two paragraphs.  Chrome
        plated cap is an option at extra cost.
        4.  Cap:  Same as housing.
        5.  Cap:  Chrome plated.
        6.  Housing diameter:  8-3/4 inches (222 mm).
        7.  Height:  8 inches (203 mm).
NOTE ** Delete the following if not applicable -- applies
        to aluminum only.
        8.  Flange:  Asphalt-coated.

    B.  Marathon Aluminum Insulvent:
        1.  Heavy gage spun aluminum.
        2.  Secured cap to prevent entry of wind-blown rain or
            snow.
        3.  4-inch (101 mm) diameter base opening.
        4.  10-3/4 inch (273 mm) diameter flange.
NOTE ** Select uncoated flange for EPDM membranes, primed
        flange for BUR and modified bitumen membranes, PVC-
        coated for PVC membranes.  Delete all but one of
        the coating options, below.
            a.  Uncoated.
            b.  Primed for adhesion to asphaltic membranes.
            c.  PVC-coated, for heat welded membrane attachment.
        5.  8-1/2 inches overall height.
NOTE ** Select either one or two-way design.  Delete
        optional insulation if not required.
        6.  One-way valve to prevent moisture re-entry.
        7.  Two-way design to allow both exhaust and convective
            air movement to create equalized pressure.
        8.  Expanded polystyrene foam insulation, to prevent
            condensation.
NOTE ** In the following paragraph, select either Medium
        Capacity or Large Capacity.

    C.  Marathon Aluminum MC (Medium Capacity) and LC (Large
        Capacity) Vent:
        1.  Heavy gage spun aluminum.
        2.  Secured cap to prevent entry of wind-blown rain or
            snow.
        3.  MC: 8-inch (203 mm) diameter base opening and 10-inch
            (254 mm) diameter flange.
        4.  LC: 10-inch (254 mm) diameter base opening and 12-
            inch (304 mm) diameter flange.
NOTE ** Select uncoated flange for EPDM membranes, primed
        flange for BUR and modified bitumen membranes, PVC-
        coated for PVC membranes.  Delete all but one of
        the coating options, below.
            a.  Uncoated.
            b.  Primed for adhesion to asphaltic membranes.
            c.  PVC-coated, for heat welded membrane attachment.
        5.  MC:  6-1/2 inches (165 mm) overall height.
        6.  LC:  8 inches (203 mm) overall height.
NOTE ** Select either one or two-way design.  Delete
        optional insulation if not required.
        7.  One-way valve to prevent moisture re-entry.
        8.  Two-way design to allow both exhaust and convective
            air movement to create equalized pressure.
        9.  Expanded polystyrene foam insulation.

    D.  Marathon Aluminum SC Vent (Small Capacity):
        1.  Heavy gage spun aluminum.
        2.  Secured cap to resist vandals.
        3.  2-7/8-inch (73 mm) diameter base opening.
        4.  6-inch (152 mm) diameter flange.
NOTE ** Select uncoated flange for EPDM membranes, primed
        flange for BUR and modified bitumen membranes, PVC-
        coated for PVC membranes.  Delete all but one of
        the coating options, below.
            a.  Uncoated.
            b.  Primed for adhesion to asphaltic membranes.
            c.  PVC-coated, for heat welded membrane attachment.
        5.  4-1/4 inches (108 mm) overall height.
NOTE ** Select either one or two-way design.
        6.  One-way valve to prevent moisture re-entry.
        7.  Two-way design to allow both exhaust and convective
            air movement to create equalized pressure.

    E.  Marathon Ex-Flow Insulation Vent:
NOTE ** Select either HDPE for bituminous membranes, or PVC
        for PVC and urethane foam membranes.
        1.  High density polyethylene construction.
        2.  PVC construction.
        3.  Secured cap to prevent entry of wind-blown rain or
            snow.
        4.  5-1/4-inch (133 mm) diameter base opening.
        5.  10-1/2-inch (266 mm) diameter flange.
        6.  8 inches (203 mm) overall height.
        7.  One-way valve to prevent moisture re-entry.

2.9 SOIL VENT STACK FLASHINGS

    A.  Marathon High Security Vent Stack Flashing:
        1.  Lead-free, tamper-resistant construction.
        2.  Heavy gage spun aluminum.
        3.  7-inch (177 mm) diameter base opening; 4-inch (101
            mm) DWV pipe capacity with hub.
        4.  15-1/4-inch (387 mm) diameter flange.
        5.  15-1/4 inches (387 mm) overall height.


PART 3  EXECUTION

3.1 EXAMINATION

    A.  Verify that dimensions are correct and substrate is in
        proper condition for installation.  Correct
        unsatisfactory conditions before proceeding with
        installation.

    B.  Verify elevation of drain to provide positive drainage.
NOTE ** Delete the following article if no retrofit drains
        are required.

3.2 PREPARATION

    A.  Remove bitumen, gravel, debris, adhesives, etc., from
        existing drain and pipe inlet.  Ensure that surface of
        drain and pipe inlet is clean and dry;  employ hot air
        gun if necessary to remove moisture.  Verify that I.D. of
        existing drain does not exceed O.D. of new outlet by more
        than 1/4 inch (6 mm).

    B.  Verify that deck opening is sufficient to accommodate the
        O.D. of connector.  Where large existing drain bowl is
        encountered use funnel profile.  If using new straight
        profile drain, provide support for the flange by
        installing 1/2 inch (12 mm) pressure-preservative-treated
        plywood, rigid high compressive strength insulation, or
        by filling bowl with spray polyurethane foam.

3.3 ROOF DRAIN INSTALLATION
NOTE ** Retain installation paragraphs below of products
        specified in Part 2.  Delete inapplicable
        paragraphs.

    A.  Flange Drains:
        1.  Set flange in a full bed of mastic or adhesive, and
            mechanically fasten flange through roofing assembly
            to the deck.
        2.  Strip in drain flange in accordance with membrane
            manufacturer's instructions.
NOTE ** Delete one or both the following paragraphs if
        inapplicable.
        3.  Do not allow flame of torch used to apply modified
            bitumen to come in contact with flange.
        4.  Hand tighten clamping ring with 7/16-inch (11 mm)
            hand wrench.

3.4 ROOF DRAIN OUTLET CONNECTIONS
NOTE ** Retain connection instructions, below, applicable
        to roof drains specified in Part 2.  Delete
        inapplicable paragraphs.
NOTE **
NOTE ** Connection of drain outlets to new or existing
        piping must be specified either in this section, or
        in Division 15.  Mechanical drains are commonly
        installed by plumbing trades.  Retrofit-style
        drains are commonly installed by roofing trades.

    A.  Flange/Pipe Roof Drains:
NOTE ** Of the three paragraphs, below, retain only those
        outlet styles that have been retained in Part 2,
        above.
        1.  Connect to piping in accordance with provisions
            specified in Division 15.
        2.  Expansion connections:  Hand tighten compression
            bands with torque wrench calibrated to 60 inch-pounds
            (759,600 N m).  Adjust if required to make water
            tight.
        3.  PVC hub fittings:  Solvent weld using compatible
            solvent cement in accordance with manufacturer's
            instructions to achieve a water tight connection.

    B.  Flange/Sleeve Drains:
        1.  Set drain outlet inside of existing drain, using
            rubber type sealant and O-rings to ensure a water-
            tight connection between drain and existing pipe.

    C.  Flange/Expansion-Sleeve Drains:
        1.  Apply sealant to outlet and existing drain leader.
            Apply an additional amount to top inside of existing
            drain pipe.  Spread sealant evenly around whole
            outlet, extending at least 5 inches (127 mm) up lower
            portion.
        2.  Set drain outlet inside of existing drain.
        3.  Expand malleable metal outlet at beginning at top of
            drain pipe and leaving 1 inch (25 mm) distance
            between expansions.  Use Proliner Expander Tool Kit
            with properly sized accessories.  Use 12 half-turns
            for 3-inch (76 mm) and 4-inch (101 mm) diameter
            drains, and 9 half-turns for 5-inch (127 mm) and 6-
            inch (152 mm) diameter drains.  Verify that outlet
            has been sufficiently expanded to ensure a water-
            tight connection between drain and existing pipe.
            Adjust if necessary.

    D.  Flange/Mechanical-Seal Retrofit Drains:
        1.  Set drain outlet inside of existing drain.
        2.  Uniformly tighten the 3 seal screws until quite snug
            to ensure a water-tight connection between drain and
            existing pipe.

    E.  Mechanical Drains:
NOTE ** Of the three paragraphs, below, retain only those
        outlet styles that have been retained in Part 2,
        above.
        1.  Connect to piping in accordance with provisions
            specified in Division 15.
        2.  Expansion connections:  Hand tighten compression
            bands with torque wrench calibrated to 60 inch-pounds
            (759,600 N m).  Adjust if required to make water
            tight.
        3.  PVC hub fittings:  Solvent weld using compatible
            solvent cement in accordance with manufacturer's
            instructions to achieve a water tight connection.

    F.  Parapet/Scupper Drains:  Connect to piping in accordance
        with provisions specified in Division 15.

    G.  Install strainer domes.
NOTE ** Delete the following article if roof vents are not
        required.

3.5 ROOF VENT INSTALLATION
NOTE ** Delete the following paragraph if vents are
        installed in new membranes only.

    A.  Existing Membranes:  Remove bitumen, gravel, debris,
        adhesives, etc., from area to receive vent.

    B.  Core through membrane and insulation to deck.
        1.  Do not disturb vapor barrier, if any.
        2.  Set flange in a full bed of mastic or adhesive.
        3.  Strip in vent flange in accordance with membrane
            manufacturer's instructions.
NOTE ** Delete the following paragraph if inapplicable.
        4.  Do not allow flame of torch used to apply modified
            bitumen to come in contact with flange.
NOTE ** Delete the following article if soil vent stack
        flashings are not required.

3.6 SOIL VENT STACK FLASHING INSTALLATION

    A.  Set flange in a full bed of mastic or adhesive.
        1.  Strip in stack flange in accordance with membrane
            manufacturer's instructions.
NOTE ** Delete the following paragraph if inapplicable.
        2.  Do not allow flame of torch used to apply modified
            bitumen to come in contact with flange.

3.7 CLEANING AND PROTECTION

    A.  Clean work area of debris associated with roofing
        specialties.

    B.  Protect finished work.


                         END OF SECTION