home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Media Share 9
/
MEDIASHARE_09.ISO
/
hamradio
/
tnet_x1h.zip
/
BANKSWIT.X1H
next >
Wrap
Text File
|
1992-09-07
|
4KB
|
94 lines
BANKSWITCHING FOR TheNet X1
What follows is two versions of how to do the bankswitching.
Saying things in two different ways is a neat way of making sure
that ambiguities are exposed, so here goes. The first version is
by me, the second by Bob G8HBE.
===============================
For the reduced TNC2 version, the instructions are simply as
follows :
1. Bend out pin 1 of the EPROM so that when inserted into
the socket it will not contact pin 1 of the socket or
any other pin.
2. Connect a wire from the SIO-0 DTRA pin ( pin 16 ) to
the bent out pin ( pin 1 ) of the eprom. The DTRA
signal should also appear on pin 8 of the TAPR modem
disconnect header.
The status led will flicker as it now shows the state of the
bankswitch signal.
One word of caution - if you can, just check the signal on pin 1
of the eprom - make sure it switches fast and cleanly - i suspect
that if it does not, errors will occur.
===============================
Robert Smith
38 Norris Close,
Chiseldon,
Nr Swidon,
Wiltshire.
SN4 0LR
6 October 1991
BANKSWITCHING for TheNet X1
So that the 27C512 does not get damaged by the bending of pin 1
and soldering it I have made the modification to the TNC-200,
Tiny 2 and MFJ1274 type TNC's as follows.
To modify your TNC you will require a piece of thin connecting
wire about 100 mm long and a 28 pin IC socket, you may also need
a little bit of inserlating tap.
Before starting the modification make sure that power to the TNC
has been disconnected and that the lithium battery link as been
removed.
Remove the 27C256, U23 in a MFJ1274/TNC200 or U2 on a Tiny 2 and
put it in a safe place.
Taking your New 28 pin IC socket, bend pin 1 outwards and solder
the end of the wire to the bent out pin.
Plug the IC socket into the socket you took the 27C256 from,
making sure that you plug it in the correct way round.
Depending on the type of IC socket that is mounted on the PC
board you may find that pin 1 on both IC sockets may touch, if
this seems to be the case put a little pieces of inserlating tap
between them.
Also on the Tiny 2 make sure that the bent pin does not touch the
CPU chip.
Now connect the other end of the wire to pin 16 on the Z80 SIO
chip.
This signal can also be found on pin 8 of the modem disconnect
header which is J5 on a Tiny 2, also the same signal can be found
on pin 5 of U6 (74HC14) on the Tiny 2. On a TNC200 you can
connect the wire to the side of R51 nearest U23, this is just 20
mm from pin 1 of U23 on the TNC200 board.
If in doubt use a test meter and check the continuity from pin 16
on the Z80 SIO chip to the point where you are going to solder
the wire.
Once you have done this you can plug the new 27C512 Programmed
with TheNet X into the new mounted IC sockets.
Re-insert the lithium battery link, Connect your computer to the
RS232 socket, 12 volts to the TNC and switch on, if all is
working well the the STA light will be flickering and after a
second a message will appear on you screen.
Modification complete.
G8HBE 6-Oct-91