home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Internet Info 1997 December
/
Internet_Info_CD-ROM_Walnut_Creek_December_1997.iso
/
install
/
qpv
/
cfg
/
ncr.cfg
< prev
next >
Wrap
Text File
|
1995-04-03
|
2KB
|
62 lines
# QPV/386 configuration file
# for SVGAs equipped with an NCR 77C22 chipset (+ optional hicolor DAC)
#
# Note: Depending on your BIOS version it may be necessary to load
# a special driver (SETMODE.SYS) in order to be able to use this
# configuration.
NCR BGR
#'NCR 77C22
#"NCR 77C22 graphics cards with hicolor DAC
# These are the standard VGA modes
320 200 16 40 $0d 0
640 480 16 80 $12 0
320 200 256 320 $13 0
# 16 color SVGA modes:
800 600 16 100 $58 0
1024 768 16 128 $5b 0 # (interlaced)
# 1024 768 16 128 $5d 0 # (non-interlaced)
1280 1024 16 160 $67 0 # (interlaced)
# Note: some cards and/or monitors do not support the 1280x1024 resolution.
# If this is true for you, delete the corresponding line in order to prevent
# QPV/386 from using that mode.
# 256 color SVGA modes:
640 480 256 640 $5f 0
800 600 256 800 $5c 0
1024 768 256 1024 $61 0 # NCR 77C22E only! (interlaced)
# 1024 768 256 1024 $62 0 # NCR 77C22E only! (non-interlaced)
1280 1024 256 1280 $6a 0 # NCR 77C22E only! (interlaced)
# 1280 960 256 1280 $6b 0 # NCR 77C22E only! (non-interlaced)
# Some cards and/or monitors do not support the 1280x1024/960 resolution.
# Note: Be sure that your SVGA card has enough video memory to display all of
# these modes. Otherwise delete the corresponding lines in order to prevent
# QPV/386 from using those modes not supported by your card.
# 32K color (hicolor) modes.
# Delete them if you don't have a hicolor or truecolor DAC.
640 480 32k 1280 $70 0 # NCR 77C22E only!
800 600 32k 1600 $71 0 # NCR 77C22E only!
# 64K color (hicolor) modes.
# If your DAC is capable of 64K color modes, you may uncomment the
# following lines (remove the '#' characters).
# 640 480 64k 1280 $78 0 # NCR 77C22E only!
# 800 600 64k 1600 $79 0 # NCR 77C22E only!
# NOTE:
# You probably need to setup some modes with softmode.sys (at least for
# the HiColor modes).
# Use setmode to adjust these values or do it by hand.
# However, if you use softmode.sys to adjust one SGVA mode,
# you must adjust them all !
#
# In your config.sys will show up (if you use setmode) something like this.
# (100 & 102 are for the 32k Hicolor modes)
#
# DEVICE=C:\NCR\softmode.sys /m:7,5,3,4,10,0,2,100,102
#
# change path C:\NCR to your own needs