home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
High Voltage Shareware
/
high1.zip
/
high1
/
DIR31
/
KERM313.ZIP
/
PP14400.SCR
< prev
next >
Wrap
Text File
|
1993-07-07
|
5KB
|
128 lines
; FILE PP14400.SCR (MSMPP144.SCR)
;
; An MS-DOS Kermit script program for dialing the Practical Peripherals
; 14400 modem, to be used with MS-DOS Kermit 3.11 or later.
; The modem is set up for compression, error correction, all types of fallback.
; RTS/CTS flow control, fixed interface speed of 57600 or 38400.
;
; Authors: Christine M. Gianone, Frank da Cruz; Columbia U, June 1993
;
def errfail echo \%1, hangup, goto fail ; Macro to handle failures.
if < VERSION 312 errfail {MS-DOS Kermit 3.12 or later required.}
if eq "\v(system)" "UNIX" if = \v(local) 0 stop 1 You must SET LINE first
define chkerr if fail stop 1 \%1
define chkok input 3 OK, if fail stop 1 \%1
set input echo on ; So we can watch what happens.
set input timeout proceed ; Allow IF SUCCESS, IF FAILURE.
set input case ignore ; Use caseless string comparisons
set parity none ; Avoid parity foulups
set flow none ; Avoid flow control deadlocks
hangup ; Begin by dropping DTR
pause 1 ; for one second
; Speed. Don't worry about modem, it autobauds up to 14400.
set speed 57600 ; If computer can be set to 57600 bps, use it.
if fail set speed 38400 ; If not, use 38400.
echo Configuring Practical Peripherals 14400 on \v(line).
wait 0 DSR ; Check modem signals that should be on
chkerr {No DSR signal - check your modem and cable}
wait 0 CTS
chkerr {No CTS signal - check your modem and cable}
:INIT
output ATQ0V1\13 ; Enable word result codes
chkok {Can't get modem's attention}
output AT E1 W1 S95=47 X4\13 ; Echoing, result codes, etc.
chkok {Can't initialize modem}
echo Enabling modulation negotiation...
output AT S37=11 N1\13 ; Start modulation speed negotiation at V32bis
chkok {Can't enable modulation speed negotiation}
echo Enabling hardware flow control...
output AT &K3\13 ; RTS/CTS hardware flow control
chkok {Can't enable RTS/CTS} ; On modem
set flow rts/cts ; And in Kermit too, but only now
echo Configuring modem to ignore BREAK...
output AT S82=128\13 ; Make modem ignore BREAK
chkok {Can't become transparent to BREAK}
echo Enabling error correction and data compression...
output AT &Q5 S36=7 S46=2\13 ; Enable error correction & compression
; with automatic speed buffering
chkok {Can't enable compression EC and fallback}
if def \%1 if not equal "\%1" "=" goto BEGIN
echo Modem initialization complete, no number to dial
end 0
:BEGIN ; Now DIAL.
clear ; Clear INPUT buffer.
set count 5 ; Dialing retry counter, 5 tries allowed.
echo Dialing \%1 on \v(line) at \v(speed) bps, wait...
echo
pause 1
goto dial ; 1st time, skip pause and Redialing message
:REDIAL
set alarm 30
pause 30 ; Wait 30 seconds before redialing.
if not alarm errfail {Dialing canceled.}
echo Redialing... ; Message for redialing.
pause 1
:DIAL
output ATD\%1\13 ; Dial the number.
set alarm 90 ; (For detecting keyboard interruptions.)
if > VERSION 312 clear input ; Clear echo from INPUT buffer.
if < VERSION 313 clear
input 30 \10 ; Wait for the linefeeds...
:GETMSG
input 60 \10 ; ...that surround the response message.
if success goto gotmsg ; Got a message.
if alarm errfail {No response from modem.} ; No response in 90 seconds.
hangup ; User interrupted from keyboard,
output \13 ; cancel dialing by sending carriage return,
goto again ; and go try again right away.
:GOTMSG
reinput 1 CONNECT ; Got a message, was it CONNECT?
if success goto done ; If so, we're done.
reinput 1 BUSY ; Line is busy.
if success goto busy ; Go wait a while and then dial again.
reinput 1 ERROR ; Command syntax error.
if success errfail {Dialing command error}
reinput 1 NO CARRIER ; Phone didn't answer or no carrier.
if success errfail {No answer or no carrier}
reinput 1 NO DIALTONE ; No dialtone when phone taken off hook.
if success errfail {No dialtone - Is your modem connected to the phone line\63}
goto getmsg ; None of the above, get another message.
:BUSY
if < \v(count) 2 goto quit ; Don't wait 30 seconds if tries are used up.
Echo Line is busy, will dial again in 30 seconds
echo Press any key to cancel...
output \13 ; CR cancels dialing
hangup ; Hang up.
:AGAIN
if count goto redial ; Then go redial.
:QUIT
errfail {It never answers! I give up.} ; Too many tries.
:DONE ; Connected.
echo \7 ; Celebrate with a beep.
define errfail ; Erase local macro definitions...
end 0 ; Finished, return success code.
:FAIL ; Dialing failed, no beep.
define errfail ; Erase local macro definitions...
end 1 ; Return failure code.
; End of PP14400.SCR