ftp.xmission.com/2014.06.ftp.xmission.com.tar/ftp.xmission.com/pub/lists/usr-tc/archive/usr-tc.200012

Internet Message Format | 2000-12-28 | 137KB

From: Brian Burgmeier <[e-mail]>
Subject: (usr-tc) command to busy out modem ports
Date: 04 Dec 2000 22:34:51 -0700

I've asked for the command before but I can seem to
find the response.  Anyway slot:15/mod:20 and slot:15/mod:19
aren't anwering.  They give either a busy signal or no answer.
I've tried to reset them but that doesn't seem to help.
Could someone again share with me the command for disabling
these two ports so that calls simply roll over to the next available
port?  Is there a real fix for this problem?  Thanks- Brian

slot:15/mod:6   rjs3                        DIALIN PPP  03-DEC-2000
22:05:17
slot:15/mod:7   khudson                     DIALIN PPP  03-DEC-2000
21:39:28
slot:15/mod:8   brianb                      DIALIN PPP  03-DEC-2000
22:06:19
slot:15/mod:9   motorctykid                 DIALIN PPP  03-DEC-2000
21:38:58
slot:15/mod:10  salatega                    DIALIN PPP  03-DEC-2000
21:38:51
slot:15/mod:11  jprice                      DIALIN PPP  03-DEC-2000
21:47:09
slot:15/mod:12  azred                       DIALIN PPP  03-DEC-2000
22:02:38
slot:15/mod:13  kcrust                      DIALIN PPP  03-DEC-2000
21:38:05
slot:15/mod:14  jaeen                       DIALIN PPP  03-DEC-2000
21:38:39
slot:15/mod:15  baseballfans                DIALIN PPP  03-DEC-2000
21:49:08
slot:15/mod:16  heartsfire                  DIALIN PPP  03-DEC-2000
21:35:39
slot:15/mod:17  tawz                        DIALIN PPP  03-DEC-2000
22:12:47
slot:15/mod:18  mn64827                     DIALIN PPP  03-DEC-2000
21:35:35
slot:15/mod:21  amari                       DIALIN PPP  03-DEC-2000
21:35:25
slot:15/mod:22  dsrtmoon                    DIALIN PPP  03-DEC-2000
21:46:50
slot:15/mod:23  kenkenco                    DIALIN PPP  03-DEC-2000
22:04:22
slot:15/mod:24  cullings                    DIALIN PPP  03-DEC-2000
21:35:19
HiPer>>

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Veda Narayan <[e-mail]>
Subject: Re: (usr-tc) command to busy out modem ports
Date: 04 Dec 2000 09:49:44 -0600

Quoting Brian Burgmeier <[e-mail]>:

> I've asked for the command before but I can seem to
> find the response.  Anyway slot:15/mod:20 and slot:15/mod:19
> aren't anwering.  They give either a busy signal or no answer.
> I've tried to reset them but that doesn't seem to help.
> Could someone again share with me the command for disabling
> these two ports so that calls simply roll over to the next available
> port?  Is there a real fix for this problem?  Thanks- Brian
>

What version of code are you using on the HiPer arc and the HiPer DSP?

V

> slot:15/mod:6   rjs3                        DIALIN PPP  03-DEC-2000
> 22:05:17
> slot:15/mod:7   khudson                     DIALIN PPP  03-DEC-2000
> 21:39:28
> slot:15/mod:8   brianb                      DIALIN PPP  03-DEC-2000
> 22:06:19
> slot:15/mod:9   motorctykid                 DIALIN PPP  03-DEC-2000
> 21:38:58
> slot:15/mod:10  salatega                    DIALIN PPP  03-DEC-2000
> 21:38:51
> slot:15/mod:11  jprice                      DIALIN PPP  03-DEC-2000
> 21:47:09
> slot:15/mod:12  azred                       DIALIN PPP  03-DEC-2000
> 22:02:38
> slot:15/mod:13  kcrust                      DIALIN PPP  03-DEC-2000
> 21:38:05
> slot:15/mod:14  jaeen                       DIALIN PPP  03-DEC-2000
> 21:38:39
> slot:15/mod:15  baseballfans                DIALIN PPP  03-DEC-2000
> 21:49:08
> slot:15/mod:16  heartsfire                  DIALIN PPP  03-DEC-2000
> 21:35:39
> slot:15/mod:17  tawz                        DIALIN PPP  03-DEC-2000
> 22:12:47
> slot:15/mod:18  mn64827                     DIALIN PPP  03-DEC-2000
> 21:35:35
> slot:15/mod:21  amari                       DIALIN PPP  03-DEC-2000
> 21:35:25
> slot:15/mod:22  dsrtmoon                    DIALIN PPP  03-DEC-2000
> 21:46:50
> slot:15/mod:23  kenkenco                    DIALIN PPP  03-DEC-2000
> 22:04:22
> slot:15/mod:24  cullings                    DIALIN PPP  03-DEC-2000
> 21:35:19
> HiPer>>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>



===========

-V

==========

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Randy Lyle <[e-mail]>
Subject: (usr-tc) Text file??
Date: 04 Dec 2000 10:43:35 -0500

Does anyone know of a program that you can use to create a setup file for a
chassis that is on an IP address, run it and have the chassis setup for
different address?

What I want to do, is re-configure a whole chassis Ip pools, NMC Ip, ARC
Ip, and all else. Would be nice if I had a program that could view and edit
a .CFM, or .NVR and then re-upload the changes.

Does anyone have an easy solution for this?
TIA
Randy
[e-mail]


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Mr. DOL" <[e-mail]>
Subject: (usr-tc) ibook and serial port to speak with tc racks
Date: 04 Dec 2000 10:00:13 -0700

I have an mac ibook with no serial port.  I am buying a usb serial
port that will plug into the ibook so that I can use the ibook
to communicate with my tc racks and configure them from the serial
port.  My old win laptop is almost dead and I am hoping this will
work. Does anyone use an ibook for serial tasks?  Is there a recommended
program to get to make this work?

thanks
eric




-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Denis Newkirk <[e-mail]>
Subject: Re: (usr-tc) FS: Hiper DSP's
Date: 04 Dec 2000 15:06:59 -0500

I have some Hiper  DSPs for sale. At least 5 left along with three chassis
and quad cards too.

If anyone needs any, please feel free to email me directly with an offer.

Most items now available (have been replaced by company which bought us
out). List is here:

http://home.early.com/~dnewkirk/equip/



At 11:25 PM 11/18/00 -0800, you wrote:
>Still have any hiper's? I will need one soon.
>Thanks,
>John Scrivner
>
>PS. Please email me at [e-mail]. I will get your message sooner.
>
>"Steve Rivera -www.wrca.net" wrote:
>
> > WR Communication Associates (WRCA) has the following USR equipment
> available:
> >
> > Hiper DSP $2900
> > Hiper NMC w/ nics (NEW) $1500
> > Hiper NMC, no nic $800 or BO
> > EdgeServer w/ SCSI nic $1200
> >
> > Try me for all you USR Hardware needs.
> > Largest Stocking Total Control Dealer on the Net.
> >
> > Chassis's, modems, power, cards, filler plates, cables...I have it all.
> >
> > Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
> > (www.isp-networkhardware.com)
> > Email: [e-mail] - Mobile Email: [e-mail]
> >
> > Worldwide Provider of Network Hardware Since 1981.
> >
> >
> >
> > -
> >  To unsubscribe to usr-tc, send an email to "[e-mail]"
> >  with "unsubscribe usr-tc" in the body of the message.
> >  For information on digests or retrieving files and old messages send
> >  "help" to the same address.  Do not use quotes in your message.
>
>
>-
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Veda Narayan <[e-mail]>
Subject: Re: (usr-tc) Text file??
Date: 04 Dec 2000 15:24:52 -0600

Quoting Randy Lyle <[e-mail]>:

> Does anyone know of a program that you can use to create a setup file
> for a
> chassis that is on an IP address, run it and have the chassis setup for
> different address?
>
> What I want to do, is re-configure a whole chassis Ip pools, NMC Ip, ARC
>
> Ip, and all else. Would be nice if I had a program that could view and
> edit
> a .CFM, or .NVR and then re-upload the changes.
>
Well, there is no text file etc to do this.  However there is a
easy way to do this.


So you have a working chassis - say chassis-1
and you want all the configuration of that chassis on a new chassis chassis-2
First on chassis-1 you do this.

set bulk-file <filename>
save configuration

- Now you tftp this file (binary mode) to a location or to the chassis-2
hiperarc

use the following commands

set bulkfile <filname>
reboot

This load the chassis-1 configuration to chassis-2, it does include the
IP address everything, so in order to get rid of the IP address, I normally
configure chassis-1 with a IP network address for the second interface
with the IP address that chassis-2 is going to have and only place
ethernet connection on chassis-2 for interface 2

This way no configuration changes are necessary

-V

> Does anyone have an easy solution for this?
> TIA
> Randy
> [e-mail]
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>



===========

-V

==========

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Colin_McFadyen <[e-mail]>
Subject: RE: (usr-tc) FS: USR Hiper DSP (New)
Date: 05 Dec 2000 13:26:43 -0500

Hi,

I have 8 Quad RS232 cables.  Offer?

I also have a Hi-Per bundle (2 DSPs, ARC, PS...) for sale.  Offer?

Colin McFadyen
Supervisor of Operations
Carleton University Computing and Communications Services
Phone: [phone] x3721    Fax: [phone]


-----Original Message-----
Sent: Tuesday, November 21, 2000 4:51 PM


Greetings...Just came across some hardware I thought you guys may be
interested in.

**NEW** Factory Warranty
Hiper DSP card sets (NAC/NIC)
$3750.00ea

Thought I could help some of you guys out.
Let me know what you need. Mention USR list.

WTB:
Still looking for Quad RS232 cables.

Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Brian Becker" <[e-mail]>
Subject: RE: (usr-tc) FS: USR Hiper DSP (New)
Date: 05 Dec 2000 12:37:37 -0600

I don't really need it right now, but would offer $6000 for the bundle if it is a newer chassis.

-----Original Message-----
[mailto:[e-mail]]On Behalf Of Colin_McFadyen
Sent: Tuesday, December 05, 2000 12:27 PM


Hi,

I have 8 Quad RS232 cables.  Offer?

I also have a Hi-Per bundle (2 DSPs, ARC, PS...) for sale.  Offer?

Colin McFadyen
Supervisor of Operations
Carleton University Computing and Communications Services
Phone: [phone] x3721    Fax: [phone]


-----Original Message-----
Sent: Tuesday, November 21, 2000 4:51 PM


Greetings...Just came across some hardware I thought you guys may be
interested in.

**NEW** Factory Warranty
Hiper DSP card sets (NAC/NIC)
$3750.00ea

Thought I could help some of you guys out.
Let me know what you need. Mention USR list.

WTB:
Still looking for Quad RS232 cables.

Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: (usr-tc) FS: USR Quad Bundles
Date: 05 Dec 2000 14:42:44 -0500

On their way in. Complete, Guaranteed working.

5- USR HD Chassis with Single 70A Power
All bundles include the following:

NMC w/ nic
Netserver PRI w/ nic
Dual PRI w/ nic
12- Quad Digital Modems w/ nics v90 flash

Asking $2500 each.

These prices are for List users. Be sure to mention you saw this on the USR
List.

Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Dave Martin <[e-mail]>
Subject: (usr-tc) USR Quad RS-232 cables
Date: 05 Dec 2000 12:34:29 -0800

I have 31 of the USR Quad RS-232 cables (26 new, 5 removed from service)
available.  Make offer...

(I also have a Telebit NetBlazer ST available, but I suppose that's
off-topic)...

Dave Martin                 Netcetera, Inc.            [e-mail]
           "Everything is Deeply Intertwingled" -- Ted Nelson



-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: (usr-tc) WTB: USR 70amp Power Supplies
Date: 05 Dec 2000 17:41:56 -0500

WTB: Looking for PSU and PSI Sets.
If you have some available or have chassis's sitting around, I'm interested :)

Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: [e-mail] (Jeff Binkley)
Subject: (usr-tc) Callback
Date: 05 Dec 2000 18:30:14 -0500



Folks,

We have a customer who is currently using MSn but wants to switch over
to us.  We are running TC racks with HiPerArcs.  I've done everything
with this guy (delete DUN, delete dialup adapter, delete TCP/IP etc..).
The problem is (I think) is that he is requesting a callback under LCP.
I cannot find anyweher in Windows 98 where he has this setup.  Here is
the HiPerArc trace:

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    007d       21 7d 21 7d 7e 00 00 01

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP
                                 CALLBACK       06

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REJ           CALLBACK       06

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP
                                 CALLBACK       06

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REJ           CALLBACK       06

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP
                                 CALLBACK       06

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REJ           CALLBACK       06

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_ACK           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_ACK           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_ACK           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_ACK           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_ACK           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Incoming PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_ACK           ASYNC_MAP      00 0a 00 00
                                 MAGIC_NUM      00 01 d0 77
                                 PROTO_COMP
                                 AC_COMP

Outgoing PPP Data on interface: slot:5/mod:4
    LCP        CFG_REQ           MRU            05 ea
                                 ASYNC_MAP      00 00 00 00
                                 AUTH_TYPE      c0 23
                                 MAGIC_NUM      9f 85 df 0b
                                 PROTO_COMP
                                 AC_COMP
                                 MPP_MRRU       05 ea
                                 MPP_ENDPTID    00

Then it disconnects with a 650 error on his end.  Can someone poit me in
the right direction ?

Thanks,

Jeff

CMPQwk 1.42-21 9999


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jeff Mcadams <[e-mail]>
Subject: Re: (usr-tc) Callback
Date: 05 Dec 2000 19:48:47 -0500

Also sprach Jeff Binkley
>Incoming PPP Data on interface: slot:5/mod:4
>    007d       21 7d 21 7d 7e 00 00 01


>Incoming PPP Data on interface: slot:5/mod:4
>    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
>                                 MAGIC_NUM      00 01 d0 77
>                                 PROTO_COMP
>                                 AC_COMP
>                                 CALLBACK       06

>Outgoing PPP Data on interface: slot:5/mod:4
>    LCP        CFG_REJ           CALLBACK       06

They request callback and you send a Reject back for it...that they send
it a couple more times is a broken implementation.

>Incoming PPP Data on interface: slot:5/mod:4
>    LCP        CFG_REQ           ASYNC_MAP      00 0a 00 00
>                                 MAGIC_NUM      00 01 d0 77
>                                 PROTO_COMP
>                                 AC_COMP

But...eventually it does give up on it...so...while this will slow down
the login process eventually (once they get the point where they are
successfully logging in)...its not preventing it.  If you can fix this,
great, it'll prevent a couple of round-trip times, but it won't prevent
them from logging in.

>Then it disconnects with a 650 error on his end.  Can someone poit me
>in the right direction ?

You're going to need to get a log from their end probably.  Here's the
problem that I see in your trace.  Their side seems to not being
responding in any way to what you're sending.  This actually will
probably change my above advice.  From what I've seen, Windows DUN tries
to negotiate callback control protocol, but will drop it, as should be
the case when it gets a config reject.

Based on the rest of the trace though, the doze machine is not
responding to your config requests at all (no acks, naks or even rejs),
it also seems to not be seeing your rejects to its initial rejects (as
discussed above), and also not seeing your acks once it drops the
callback as it continues to send new requests.

Its odd, but it looks like you've got one-way communications here, but
not two-way.  You're seeing what they're sending, but they're not seeing
what you're sending.

I guess there is a possibility that their system is seeing your packets
as corrupt or something like that for some reason and is thus silently
dropping them.  That's why I suggest getting a log from their side.
There's an option in DUN (don't ask me where to find it) to record a PPP
log (note, this is *NOT* the modem log file that is much easier to
find).  Enable that and look at the output...that might give you some
insight into what's happening.  Feel free to drop a line to me or the
list and someone (myself, if noone else gets to it) can help decipher
it.
--
Jeff McAdams                            Email: [e-mail]
Head Network Administrator              Voice: [phone]
IgLou Internet Services                        [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jeff Mcadams <[e-mail]>
Subject: Re: (usr-tc) Callback
Date: 05 Dec 2000 19:57:52 -0500

Also sprach Jeff Mcadams
>Also sprach Jeff Binkley
>>Incoming PPP Data on interface: slot:5/mod:4
>>    007d       21 7d 21 7d 7e 00 00 01

Dang!  Forgot to comment on this one...

I haven't a clue what this packet it.  The HiPer Arc flags it as packet
type 007d which rfc1661 says is "reserved (Control Escape)"  What on
earth in doze is using that?  I haven't a clue...it doesn't seem to be a
significant problem though as its not repeated and doesn't through the
Arc off its stride in any way.
--
Jeff McAdams                            Email: [e-mail]
Head Network Administrator              Voice: [phone]
IgLou Internet Services                        [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Discount Domain Name Services" <[e-mail]>
Subject: (usr-tc) Date: Wed, 6 Dec 2000 17:09:33 +1100
Date: 05 Dec 2000 23:05:57 -0700

We have a total control unit complete for sale 12 months old with all the
software and shipping cartons never been over 20 users ( just like driven to
church on sundays)
If there is any interest out there contact us at [e-mail]
Cheers,
Rod


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Brian Becker" <[e-mail]>
Subject: RE: (usr-tc) Date: Wed, 6 Dec 2000 17:09:33 +1100
Date: 06 Dec 2000 07:38:24 -0600

Can you give the specs?

Brian

-----Original Message-----
[mailto:[e-mail]]On Behalf Of Discount Domain
Name Services
Sent: Wednesday, December 06, 2000 12:06 AM


We have a total control unit complete for sale 12 months old with all the
software and shipping cartons never been over 20 users ( just like driven to
church on sundays)
If there is any interest out there contact us at [e-mail]
Cheers,
Rod


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Jorge Lozano" <[e-mail]>
Subject: (usr-tc) Problems with old Netserver
Date: 06 Dec 2000 16:19:20 -0500

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hi everybody:
I┤m trying to set IP filter in Netserver with "set sX ifilter
filter.in" and "set sX ofilter filter.out"

netserver> set sX ifilter mail.in
Input filter for port sX changed from  to mail.out
netserver> set sX ofilter mail.out
Output filter for port sX changed from  to mail.out

but when I try to change the filter again, in order to view the
current filter, the Netserver show to me the folliwing message:

netserver> set sX ifilter filter.in
Input filter for port sX changed from  to filter.in

from <nothing> to filter.in, can anybody tell me how can I save the
port filter info?, because using "save all" I couldn┤t.

Note: obviously, I have mail.in, mail.out and filter.in created in
Netserver.

Thanks in advance,


Jorge Lozano <[e-mail]>
NA and ISSO Andinet On Line <http://www.andinet.com>
The only way to predict the future is... to create it!

-----BEGIN PGP SIGNATURE-----
Version: PGPfreeware 6.5.8 for non-commercial use <http://www.pgp.com>

iQA/AwUBOi6tVqp3oywyFVUlEQLPDwCgnMoQfM6Mm7radJEpzFnov/xbcBAAoIho
LDKudxrVuxpwTjrE7Jwiq0BN
=vWKg
-----END PGP SIGNATURE-----


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: David DenHollander <[e-mail]>
Subject: (usr-tc) Need help finding Edgeserver Pro's
Date: 07 Dec 2000 09:49:02 -0700

I am in need of some Edgeserver Pro's any one know where I can find them?

Thanks


David DenHollander

[phone] Main
[phone] Fax

List your equipment for free
http://www.adoptable.com/









-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Brian <[e-mail]>
Subject: (usr-tc) The new HDM's
Date: 12 Dec 2000 10:54:04 -0600 (CST)


Do you have to buy one of the new HDM's to get the 96 channel capibility,
or can you simply swap out the NIC portion of the HDM?  In other words, is
their an upgrade path?

Anyone using the 96 channel HDM's or DS3 modules?

Brian


Brian Feeny, CCNP+ATM, CCDP   [e-mail]
Network Administrator
ShreveNet Inc. (ASN 11881)


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jeff Mcadams <[e-mail]>
Subject: Re: (usr-tc) The new HDM's
Date: 12 Dec 2000 11:59:57 -0500

Also sprach Brian
>Do you have to buy one of the new HDM's to get the 96 channel
>capibility, or can you simply swap out the NIC portion of the HDM?  In
>other words, is their an upgrade path?

You'll need to buy the new NAC.  The current DSP's only have 24 (30 for
E1 versions) modems on the card, so you can't handle 96 calls on the
current NACs.
--
Jeff McAdams                            Email: [e-mail]
Head Network Administrator              Voice: [phone]
IgLou Internet Services                        [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Brian <[e-mail]>
Subject: Re: (usr-tc) The new HDM's
Date: 12 Dec 2000 14:10:49 -0600 (CST)

On Tue, 12 Dec 2000, Jeff Mcadams wrote:

> Also sprach Brian
> >Do you have to buy one of the new HDM's to get the 96 channel
> >capibility, or can you simply swap out the NIC portion of the HDM?  In
> >other words, is their an upgrade path?
>
> You'll need to buy the new NAC.  The current DSP's only have 24 (30 for
> E1 versions) modems on the card, so you can't handle 96 calls on the
> current NACs.

Actually, the current NAC's have 6 DSP's, each emulates 4 modems.  I heard
that these same cards were able to actually do 8 modems per DSP about 2
years ago, and thought maybe they pushed it even further.  The plan worked
out nicely when 3Com envisioned it:

14 slots, 1 hdm per slot, 23/24 channels per slot, 1 pri/t1 per slot

but once they were able to double to 8 modems per DSP:

14 slots, 1 hdm per slot, 46/24 channels per slot, 1 DS3 for the chassis

that was the rationale behind using a utilization meter on the front of
the HDM NAC vs. a 1:1 LED per modem mapping, since this way they could
expand the NAC DSP-wise...........

The sad part is they probably have the software but won't release (the
software existed 2 years ago or so..........inside sources tell me) (that
is the software to double the modem emulation of the DSP's)

brian


> --
> Jeff McAdams                            Email: [e-mail]
> Head Network Administrator              Voice: [phone]
> IgLou Internet Services                        [phone]
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>

Brian Feeny, CCNP+ATM, CCDP   [e-mail]
Network Administrator
ShreveNet Inc. (ASN 11881)


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jeff Mcadams <[e-mail]>
Subject: Re: (usr-tc) The new HDM's
Date: 12 Dec 2000 15:30:15 -0500

Also sprach Brian
>On Tue, 12 Dec 2000, Jeff Mcadams wrote:
>> You'll need to buy the new NAC.  The current DSP's only have 24 (30
>> for E1 versions) modems on the card, so you can't handle 96 calls on
>> the current NACs.

>Actually, the current NAC's have 6 DSP's, each emulates 4 modems.  I
>heard that these same cards were able to actually do 8 modems per DSP
>about 2 years ago, and thought maybe they pushed it even further.

OK...the original DSPs cards had a dsp chip for every two modems...the
newer DSP cards have a dsp chip for every four modems (same code base).
They (according to what I've heard) are basically the same type of dsp
chips...but the newer ones are a newer version...thus the capability of
handling more modems.  I was not under the impression that it was just a
software change (though that certainly is possible).

>that was the rationale behind using a utilization meter on the front of
>the HDM NAC vs. a 1:1 LED per modem mapping, since this way they could
>expand the NAC DSP-wise...........

They also just plain didn't have enough room for 24 leds for modems
along with carrier, alarm, loopback, fail, and power leds.
--
Jeff McAdams                            Email: [e-mail]
Head Network Administrator              Voice: [phone]
IgLou Internet Services                        [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Mike Andrews <[e-mail]>
Subject: Re: (usr-tc) The new HDM's
Date: 12 Dec 2000 17:45:27 -0500 (EST)

These are actually shipping now?


Mike Andrews * [e-mail] * [e-mail] * http://www.bit0.com
VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY
Internet access for Frankfort, Lexington, Louisville and surrounding counties

www.fark.com: If it's not news, it's Fark.  (Or something like that.)

On Tue, 12 Dec 2000, Brian wrote:

>
> Do you have to buy one of the new HDM's to get the 96 channel capibility,
> or can you simply swap out the NIC portion of the HDM?  In other words, is
> their an upgrade path?
>
> Anyone using the 96 channel HDM's or DS3 modules?
>
> Brian
>
>
> -----------------------------------------------
> Brian Feeny, CCNP+ATM, CCDP   [e-mail]
> Network Administrator
> ShreveNet Inc. (ASN 11881)
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Mike Andrews <[e-mail]>
Subject: Re: (usr-tc) The new HDM's
Date: 12 Dec 2000 17:45:27 -0500 (EST)

These are actually shipping now?


Mike Andrews * [e-mail] * [e-mail] * http://www.bit0.com
VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY
Internet access for Frankfort, Lexington, Louisville and surrounding counties

www.fark.com: If it's not news, it's Fark.  (Or something like that.)

On Tue, 12 Dec 2000, Brian wrote:

>
> Do you have to buy one of the new HDM's to get the 96 channel capibility,
> or can you simply swap out the NIC portion of the HDM?  In other words, is
> their an upgrade path?
>
> Anyone using the 96 channel HDM's or DS3 modules?
>
> Brian
>
>
> -----------------------------------------------
> Brian Feeny, CCNP+ATM, CCDP   [e-mail]
> Network Administrator
> ShreveNet Inc. (ASN 11881)
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: (usr-tc) FS: USR Total Control Quad v90 bundles.
Date: 12 Dec 2000 18:09:01 -0500

WR Communication Associates (WRCA.NET) has the following USR hardware
available:
Mention USR LIST.

5 - USR HD Chassis with 70A Power
NMC
Netserver PRI
Dual PRI
12x Quad Digital modems v90

$2000.00each

Shipment includes:
CD-ROM Library
Console cable
Telco cables
30 day warranty


Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: David DenHollander <[e-mail]>
Subject: (usr-tc) For sale and WTB postings
Date: 12 Dec 2000 17:31:31 -0700

I have noticed people posting equipment for sale on this list, have the
rules changed? Is this something that anyone can do?  I used to send my
customers to this list so they could benefit from the knowledge of all
those who use the list, but I no longer do so for obvious reasons.



At 06:09 PM 12/12/00 -0500, you wrote:
>WR Communication Associates (WRCA.NET) has the following USR hardware
>available:
>Mention USR LIST.
>
>5 - USR HD Chassis with 70A Power
>NMC
>Netserver PRI
>Dual PRI
>12x Quad Digital modems v90
>
>$2000.00each
>
>Shipment includes:
>CD-ROM Library
>Console cable
>Telco cables
>30 day warranty
>
>
>Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
>(www.isp-networkhardware.com)
>Email: [e-mail] - Mobile Email: [e-mail]
>
>Worldwide Provider of Network Hardware Since 1981.
>
>
>
>
>
>
>
>
>
>
>
>
>
>-
> To unsubscribe to usr-tc, send an email to "[e-mail]"
> with "unsubscribe usr-tc" in the body of the message.
> For information on digests or retrieving files and old messages send
> "help" to the same address.  Do not use quotes in your message.
>

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Brian <[e-mail]>
Subject: Re: (usr-tc) The new HDM's
Date: 12 Dec 2000 19:47:46 -0600 (CST)


I don't know.  I got a spam fax from someone saying "Be the first to own
the new 96port HDM, blah blah".

Then the 3Com site talks about all this new gear.  I am confused.  I don't
even know what a Total Control 2000 is or whats the differnce, I need to
spend some time on their site getting back up to speed.

Brian


On Tue, 12 Dec 2000, Mike Andrews wrote:

> These are actually shipping now?
>
>
> Mike Andrews * [e-mail] * [e-mail] * http://www.bit0.com
> VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY
> Internet access for Frankfort, Lexington, Louisville and surrounding counties
>
> www.fark.com: If it's not news, it's Fark.  (Or something like that.)
>
> On Tue, 12 Dec 2000, Brian wrote:
>
> >
> > Do you have to buy one of the new HDM's to get the 96 channel capibility,
> > or can you simply swap out the NIC portion of the HDM?  In other words, is
> > their an upgrade path?
> >
> > Anyone using the 96 channel HDM's or DS3 modules?
> >
> > Brian
> >
> >
> > -----------------------------------------------
> > Brian Feeny, CCNP+ATM, CCDP   [e-mail]
> > Network Administrator
> > ShreveNet Inc. (ASN 11881)
> >
> >
> > -
> >  To unsubscribe to usr-tc, send an email to "[e-mail]"
> >  with "unsubscribe usr-tc" in the body of the message.
> >  For information on digests or retrieving files and old messages send
> >  "help" to the same address.  Do not use quotes in your message.
> >
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>

Brian Feeny, CCNP+ATM, CCDP   [e-mail]
Network Administrator
ShreveNet Inc. (ASN 11881)


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Brian <[e-mail]>
Subject: Re: (usr-tc) The new HDM's
Date: 12 Dec 2000 19:47:46 -0600 (CST)


I don't know.  I got a spam fax from someone saying "Be the first to own
the new 96port HDM, blah blah".

Then the 3Com site talks about all this new gear.  I am confused.  I don't
even know what a Total Control 2000 is or whats the differnce, I need to
spend some time on their site getting back up to speed.

Brian


On Tue, 12 Dec 2000, Mike Andrews wrote:

> These are actually shipping now?
>
>
> Mike Andrews * [e-mail] * [e-mail] * http://www.bit0.com
> VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY
> Internet access for Frankfort, Lexington, Louisville and surrounding counties
>
> www.fark.com: If it's not news, it's Fark.  (Or something like that.)
>
> On Tue, 12 Dec 2000, Brian wrote:
>
> >
> > Do you have to buy one of the new HDM's to get the 96 channel capibility,
> > or can you simply swap out the NIC portion of the HDM?  In other words, is
> > their an upgrade path?
> >
> > Anyone using the 96 channel HDM's or DS3 modules?
> >
> > Brian
> >
> >
> > -----------------------------------------------
> > Brian Feeny, CCNP+ATM, CCDP   [e-mail]
> > Network Administrator
> > ShreveNet Inc. (ASN 11881)
> >
> >
> > -
> >  To unsubscribe to usr-tc, send an email to "[e-mail]"
> >  with "unsubscribe usr-tc" in the body of the message.
> >  For information on digests or retrieving files and old messages send
> >  "help" to the same address.  Do not use quotes in your message.
> >
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>

Brian Feeny, CCNP+ATM, CCDP   [e-mail]
Network Administrator
ShreveNet Inc. (ASN 11881)


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Brian <[e-mail]>
Subject: Re: (usr-tc) For sale and WTB postings
Date: 12 Dec 2000 19:49:02 -0600 (CST)


i think USR-TC stuff for sale has always been around on this list.  I mean
we all use the stuff, and we all regularly buy the stuff, so a good deal
is something we all are looking for.  I mean, if someone has HDM's for
$1500 each,  i want to know about it :)

Brian


On Tue, 12 Dec 2000, David DenHollander wrote:

> I have noticed people posting equipment for sale on this list, have the
> rules changed? Is this something that anyone can do?  I used to send my
> customers to this list so they could benefit from the knowledge of all
> those who use the list, but I no longer do so for obvious reasons.
>
>
>
> At 06:09 PM 12/12/00 -0500, you wrote:
> >WR Communication Associates (WRCA.NET) has the following USR hardware
> >available:
> >Mention USR LIST.
> >
> >5 - USR HD Chassis with 70A Power
> >NMC
> >Netserver PRI
> >Dual PRI
> >12x Quad Digital modems v90
> >
> >$2000.00each
> >
> >Shipment includes:
> >CD-ROM Library
> >Console cable
> >Telco cables
> >30 day warranty
> >
> >
> >Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
> >(www.isp-networkhardware.com)
> >Email: [e-mail] - Mobile Email: [e-mail]
> >
> >Worldwide Provider of Network Hardware Since 1981.
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >-
> > To unsubscribe to usr-tc, send an email to "[e-mail]"
> > with "unsubscribe usr-tc" in the body of the message.
> > For information on digests or retrieving files and old messages send
> > "help" to the same address.  Do not use quotes in your message.
> >
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>

Brian Feeny, CCNP+ATM, CCDP   [e-mail]
Network Administrator
ShreveNet Inc. (ASN 11881)


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: Re: (usr-tc) For sale and WTB postings
Date: 13 Dec 2000 10:59:43 -0500

If you are really concerned for your customers tech support I would suggest
the new
[e-mail]

At 07:49 PM 12/12/2000 -0600, you wrote:

>i think USR-TC stuff for sale has always been around on this list.  I mean
>we all use the stuff, and we all regularly buy the stuff, so a good deal
>is something we all are looking for.  I mean, if someone has HDM's for
>$1500 each,  i want to know about it :)
>
>Brian
>
>
>On Tue, 12 Dec 2000, David DenHollander wrote:
>
> > I have noticed people posting equipment for sale on this list, have the
> > rules changed? Is this something that anyone can do?  I used to send my
> > customers to this list so they could benefit from the knowledge of all
> > those who use the list, but I no longer do so for obvious reasons.
> >
> >
> >
> > At 06:09 PM 12/12/00 -0500, you wrote:
> > >WR Communication Associates (WRCA.NET) has the following USR hardware
> > >available:
> > >Mention USR LIST.
> > >
> > >5 - USR HD Chassis with 70A Power
> > >NMC
> > >Netserver PRI
> > >Dual PRI
> > >12x Quad Digital modems v90
> > >
> > >$2000.00each
> > >
> > >Shipment includes:
> > >CD-ROM Library
> > >Console cable
> > >Telco cables
> > >30 day warranty
> > >
> > >
> > >Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
> > >(www.isp-networkhardware.com)
> > >Email: [e-mail] - Mobile Email: [e-mail]
> > >
> > >Worldwide Provider of Network Hardware Since 1981.
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >-
> > > To unsubscribe to usr-tc, send an email to "[e-mail]"
> > > with "unsubscribe usr-tc" in the body of the message.
> > > For information on digests or retrieving files and old messages send
> > > "help" to the same address.  Do not use quotes in your message.
> > >
> >
> > -
> >  To unsubscribe to usr-tc, send an email to "[e-mail]"
> >  with "unsubscribe usr-tc" in the body of the message.
> >  For information on digests or retrieving files and old messages send
> >  "help" to the same address.  Do not use quotes in your message.
> >
>
>-----------------------------------------------
>Brian Feeny, CCNP+ATM, CCDP   [e-mail]
>Network Administrator
>ShreveNet Inc. (ASN 11881)
>
>
>-
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: (usr-tc) FS: USR Netserver's and MP's
Date: 18 Dec 2000 12:01:14 -0500

WR Communication Associates (WRCA.NET) has the following USR hardware
available.
All shipped with 30 day warranty. Rack ears and Manuals included.

Analog
5- Netserver 16 v34 $700
7- MP 16 v34 $600
2- MMP16 v34 $650
4- MP 8 v34 $500

ISDN-BRI
2- Netserver 8I $850
1- MP 8I $750




Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Mike Andrews <[e-mail]>
Subject: (usr-tc) cheap winmodem issues
Date: 18 Dec 2000 12:36:26 -0500 (EST)

Is it just me, or has anyone else noticed a sharp *decrease* in the number
of problems with Rockwells and such with DSP code 2.1.9?  Or is it just
that vendors are actually shipping newer drivers these days?  I'm not
complaining either way, just trying to see if this is typical, or if my
tech support people just stopped telling me about the problems, or what.
:)


Mike Andrews * [e-mail] * [e-mail] * http://www.bit0.com
VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY
Internet access for Frankfort, Lexington, Louisville and surrounding counties
www.fark.com: If it's not news, it's Fark.  (Or something like that.)


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Wayne Barber" <[e-mail]>
Subject: Re: (usr-tc) cheap winmodem issues
Date: 18 Dec 2000 14:30:31 -0500

Decrease, yes; elimination, no. I think it has been a combination of
both the server and client side software gettting better. Or maybe
the problems just all migrated to those &*($@% PCTEL modems.

On 18 Dec 2000, at 12:36, Mike Andrews wrote:

> Is it just me, or has anyone else noticed a sharp *decrease* in the
> number of problems with Rockwells and such with DSP code 2.1.9?  Or is
> it just that vendors are actually shipping newer drivers these days?
> I'm not complaining either way, just trying to see if this is typical,
> or if my tech support people just stopped telling me about the
> problems, or what. :)
>
>
> Mike Andrews * [e-mail] * [e-mail] *
> http://www.bit0.com VP, sysadmin, & network guy, Digital Crescent Inc,
> Frankfort KY Internet access for Frankfort, Lexington, Louisville and
> surrounding counties www.fark.com: If it's not news, it's Fark.  (Or
> something like that.)
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message. For information
>  on digests or retrieving files and old messages send "help" to the
>  same address.  Do not use quotes in your message.
>



Wayne Barber
Coastal Telco Services

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Joe Rinehart <[e-mail]>
Subject: Re: (usr-tc) FS: USR Netserver's and MP's
Date: 19 Dec 2000 00:58:56 -0500

This is a cryptographically signed message in MIME format.

--------------msAD26F61BBBCEB0500379C37A
Content-Type: multipart/mixed;
 boundary="------------FD3B6A17FD52C4ADAD356801"

This is a multi-part message in MIME format.
--------------FD3B6A17FD52C4ADAD356801
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit

Steve,

We got our refurbished DSP card and all is working beautifully!

I thought I'd take the time to thank you publicly for both a great deal
and level of service regarding my questions and initial problem. The
problem turned out to be the card was configured for a trunk circuit
instead of a PRI. Once it was compared and set for an existing PRI, it's
been flawless since.

Now, if I can just get a new circuit from Ameritech installed as prompt
as I got your card;^)

Best 'net regards,
Joe
--
Joe Rinehart, Operations Designer Config.Com, Inc.
124 North Chestnut Street, Ravenna, OH 44266
T: 330.297.9595 F:330.296.4005 H:330.298.4396
http://joerinehart.com/ mailto:[e-mail]
finger:[e-mail]


--------------FD3B6A17FD52C4ADAD356801
Content-Type: text/x-vcard; charset=us-ascii;
 name="joe.vcf"
Content-Transfer-Encoding: 7bit
Content-Description: Card for Joe Rinehart
Content-Disposition: attachment;
 filename="joe.vcf"

begin:vcard
n:Rinehart;Joe
tel;fax:[phone]
tel;home:330.298.9239
tel;work:330.297.9595
x-mozilla-html:FALSE
url:http://www.config.com/
org:Config.Com, Inc.;Network Administration
adr:;;124 North Chestnut Street;Ravenna;Ohio;44266-2254;USA
version:2.1
email;internet:[e-mail]
title:Operations Designer
note;quoted-printable:Wife: Rose=0D=0AChildren: Jeremiah 3, James 20, Jean 23=0D=0AHobbies: Sailing, sushi, & Shoshana
fn:Joe Rinehart
end:vcard

--------------FD3B6A17FD52C4ADAD356801--

--------------msAD26F61BBBCEB0500379C37A
Content-Type: application/x-pkcs7-signature; name="smime.p7s"
Content-Transfer-Encoding: base64
Content-Disposition: attachment; filename="smime.p7s"
Content-Description: S/MIME Cryptographic Signature
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--------------msAD26F61BBBCEB0500379C37A--


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: Re: (usr-tc) FS: USR Netserver's and MP's
Date: 19 Dec 2000 11:11:04 -0500

Joe, Thank you so much for the kind words.
To you and the rest of the list......Have a great Holiday Season.

FYI:  I will be available for any possible emergency situations throughout
the Holidays...Call me ANYTIME!
732-433-5890 CELL

At 12:58 AM 12/19/2000 -0500, you wrote:
>Steve,
>
>We got our refurbished DSP card and all is working beautifully!
>
>I thought I'd take the time to thank you publicly for both a great deal
>and level of service regarding my questions and initial problem. The
>problem turned out to be the card was configured for a trunk circuit
>instead of a PRI. Once it was compared and set for an existing PRI, it's
>been flawless since.
>
>Now, if I can just get a new circuit from Ameritech installed as prompt
>as I got your card;^)
>
>Best 'net regards,
>Joe
>--
>Joe Rinehart, Operations Designer Config.Com, Inc.
>124 North Chestnut Street, Ravenna, OH 44266
>T: 330.297.9595 F:330.296.4005 H:330.298.4396
>http://joerinehart.com/ mailto:[e-mail]
>finger:[e-mail]
>
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: (usr-tc) FS: Quad Bundles ...Super Cheap...Hiper..
Date: 19 Dec 2000 17:47:24 -0500

Hello Folks, This might sound too good to be true but it is :) They are
configured as follows. Don't be hesitant because of price. They are in
great cosmetic and functional condition. I bought them at a great price and
since it is the giving season I though I could pass the savings to this list :)

I am always open to opportunity so if you need help with pricing and your a
serious buyer. I will work with you.
Be sure to mention you found it on the USR List.

HD Chassis with Single 70A Power
NMC
Netserver PRI
Dual PRI
12 Quad Digital Modems

1-5 $2000
6-10 $1750
11-15 $1500

Hiper DSP $3000
Hiper ARC $2000
Hiper NMC $1000
Dual PRI/E1 $650...Hard to Find

As usual I guarantee all equipment working.

If you are looking anything USR/3Com Total Control, Netservers, MP, MMP's,
nic,macs, parts ect.
YEAH I GOT THAT :)

Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Aaron Nabil <[e-mail]>
Subject: Re: (usr-tc) Power Consumption
Date: 20 Dec 2000 03:34:12 -0800 (PST)

On Tue, 28 Nov 2000, Clayton Zekelman wrote:
>  . . .
> The only real way to measure it of course is to place a fixed value shunt
> in line with DC supply, and measure the voltage drop across it, and
> calcuate the current draw.


The other "real way" is to use a clamp-on DC current probe.  The
significant advantage being that you don't have to interrupt the circuit.

--
Aaron Nabil


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Cobb" <[e-mail]>
Subject: (usr-tc) Settings?
Date: 20 Dec 2000 11:20:37 -0500

I'm using a TC with HiperDSPs and authenticating with RadiusNT in ODBC mode.  I need to be able to control concurrent logins and allow logins based on type of connection, i.e. ISDN or analog.  Can someone tell me what changes I need to make on the TC?

Thanks,

Steve Cobb

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Brian Becker" <[e-mail]>
Subject: (usr-tc) Multi-Chassis and MPPP
Date: 20 Dec 2000 10:41:50 -0600

How do you set up two chassis to work together in establishing an MPPP connection?

Brian Becker
President, Poplar Bluff Internet, Inc. (www.semo.net)
Home of TotallyFabricated.com Software:
  Total Scrutinizer (www.TotalScrutinizer.com) - Tech Support Just Got Easier!
  WebGabber (www.WebGabber.com) - html-based Chat Software


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jeff Mcadams <[e-mail]>
Subject: Re: (usr-tc) Multi-Chassis and MPPP
Date: 20 Dec 2000 11:45:33 -0500

Also sprach Brian Becker
>How do you set up two chassis to work together in establishing an MPPP
>connection?

Check out the manuals (pdf's availabe, even without a service contract,
at totalservice.3com.com) for info on MPIP.  MPIP is the coordination
protocol that Arcs use to do multi-chassis multi-link.  Be aware that
you'll need the time syncronized between the Arcs...but that's easily
done since they support NTP.  :)
--
Jeff McAdams                            Email: [e-mail]
Head Network Administrator              Voice: [phone]
IgLou Internet Services                        [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Brian Becker" <[e-mail]>
Subject: RE: (usr-tc) Multi-Chassis and MPPP
Date: 20 Dec 2000 11:06:03 -0600

This is what I got when I did a search on 3Com site...which is why I posed the question here. If someone can give me the pdf...that
would be great. <grin>

Product: Total Control 1000 : TCS 3.6
Total Control 1000 : TCS 4.2
Total Control 1000 : HiPer ARC SS7 ESIG
Total Control 1000 : VPN 1.0
Total Control 1000 : TCS 2.0.1
Total Control 1000 : TCS 2.5
Total Control 1000 : Channelized T1 cards
Total Control 1000 : EdgeServer & EdgeServer Pro
Total Control 1000 : Quad Modem
Total Control 1000 : Network Management cards
Total Control 1000 : NETServer cards
Total Control 1000 : PRI/T1 cards
Total Control 1000 : PRI/E1 cards
Total Control 1000 : TCM for Windows
Total Control 1000 : TCM for UNIX
Total Control 1000 : Security and Accounting Servers
Total Control 1000 : Misc
Total Control 1000 : TCS 1.5
Total Control 1000 : TCS 1.5.1
Total Control 1000 : TCS 2.5.1
Total Control 1000 : TCS 1.0
Total Control 1000 : TCS 3.0
Total Control 1000 : HiPer DSP
Total Control 1000 : E1 cards
Total Control 1000 : HiPer ARC
Total Control 1000 : TCS 3.0.1
Total Control 1000 : TCS 3.0.2
Total Control 1000 : TCS 3.1
Total Control 1000 : TCS 3.1.1
Total Control 1000 : TCS 3.1.2
Total Control 1000 : TCS 3.3
Total Control 1000 : SS7
Total Control 1000 : TCS 3.5
Total Control 1000 : TCS 4.0

Search Terms: mpip

Documentation Type:


Access  File Name  Size     Released  Description
No matching items were found.


-----Original Message-----
[mailto:[e-mail]]On Behalf Of Jeff Mcadams
Sent: Wednesday, December 20, 2000 10:46 AM


Also sprach Brian Becker
>How do you set up two chassis to work together in establishing an MPPP
>connection?

Check out the manuals (pdf's availabe, even without a service contract,
at totalservice.3com.com) for info on MPIP.  MPIP is the coordination
protocol that Arcs use to do multi-chassis multi-link.  Be aware that
you'll need the time syncronized between the Arcs...but that's easily
done since they support NTP.  :)
--
Jeff McAdams                            Email: [e-mail]
Head Network Administrator              Voice: [phone]
IgLou Internet Services                        [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jeff Mcadams <[e-mail]>
Subject: Re: (usr-tc) Multi-Chassis and MPPP
Date: 20 Dec 2000 12:13:00 -0500

Also sprach Brian Becker
>This is what I got when I did a search on 3Com site...which is why I
>posed the question here. If someone can give me the pdf...that would be
>great. <grin>

I don't have the pdf at hand...but there is a chapter in the HiPer
Arc...uhm...Product Reference is what I believe its called...about
setting up MPIP.
--
Jeff McAdams                            Email: [e-mail]
Head Network Administrator              Voice: [phone]
IgLou Internet Services                        [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Paul Farber <[e-mail]>
Subject: Re: (usr-tc) Settings?
Date: 20 Dec 2000 12:59:59 -0500 (EST)

That's more of a radius issue than an TC one.

Paul Farber
Farber Technology
[e-mail]
Ph  570-628-5303
Fax [phone]

On Wed, 20 Dec 2000, Steve Cobb wrote:

> I'm using a TC with HiperDSPs and authenticating with RadiusNT in ODBC mode.  I need to be able to control concurrent logins and allow logins based on type of connection, i.e. ISDN or analog.  Can someone tell me what changes I need to make on the TC?
>
> Thanks,
>
> Steve Cobb
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: [e-mail]
Subject: RE: (usr-tc) Multi-Chassis and MPPP
Date: 20 Dec 2000 15:54:44 -0600

Brian:

Here are some instructions that I received from the list a year ago on
setting up MPIP.  Hope they help.

If this works, you can send Ron and Paul a Christmas card!  They're the ones
that figured it out.

Paul Farber wrote:
>
> How many servers are their?  This is where I'm confused.  I have ARC-A and
> ARC-B.

One server.  In this example ARC-A will be the server.

On ARC-A you would type:

set mpip client_state on
set mpip server_state on
set mpip client (IP of ARC-A) sharedsecret <Secret on ARC-A>
set mpip client (IP of ARC-B) sharedsecret <Secret on ARC-B>
set mpip server (IP of ARC-A) sharedsecret <Secret for ARC-A>

set ntp primary_server <IP of NTP server>
enable ntp

save all

On ARC-B you would type:

set mpip client_state on
set mpip server (IP of ARC-A) sharedsecret <Secret for ARC-B>

set ntp primary_server <IP of NTP server>
enable ntp

save all

> Set ARC-A as mpip client + server, plus set it to an NTP server (know of
> any good ones?).

I run my own NTP server on a Linux box. Don't have to worry too much
about it going down then.

> Set ARC-B as mpip client and add ip's of ARC-A's into it (what command?).
> Set the NTP to same NTP server s ARC-A.
>
> How does ARC-B know of ARC-A's ips?  Add them their also?

You don't need to worry about IP addresses of the different ARCs. The
ARC will tunnel between each other so it is invisible to the client.

> Thanks for your help so far.

No problem,

-Ron
GLISnet, Inc.
+1 810/939.9885

Mike Storjohann
HunTel.net
[e-mail]


-----Original Message-----
[mailto:[e-mail]]On Behalf Of Brian Becker
Sent: Wednesday, December 20, 2000 11:06 AM


This is what I got when I did a search on 3Com site...which is why I posed
the question here. If someone can give me the pdf...that
would be great. <grin>

Product: Total Control 1000 : TCS 3.6
Total Control 1000 : TCS 4.2
Total Control 1000 : HiPer ARC SS7 ESIG
Total Control 1000 : VPN 1.0
Total Control 1000 : TCS 2.0.1
Total Control 1000 : TCS 2.5
Total Control 1000 : Channelized T1 cards
Total Control 1000 : EdgeServer & EdgeServer Pro
Total Control 1000 : Quad Modem
Total Control 1000 : Network Management cards
Total Control 1000 : NETServer cards
Total Control 1000 : PRI/T1 cards
Total Control 1000 : PRI/E1 cards
Total Control 1000 : TCM for Windows
Total Control 1000 : TCM for UNIX
Total Control 1000 : Security and Accounting Servers
Total Control 1000 : Misc
Total Control 1000 : TCS 1.5
Total Control 1000 : TCS 1.5.1
Total Control 1000 : TCS 2.5.1
Total Control 1000 : TCS 1.0
Total Control 1000 : TCS 3.0
Total Control 1000 : HiPer DSP
Total Control 1000 : E1 cards
Total Control 1000 : HiPer ARC
Total Control 1000 : TCS 3.0.1
Total Control 1000 : TCS 3.0.2
Total Control 1000 : TCS 3.1
Total Control 1000 : TCS 3.1.1
Total Control 1000 : TCS 3.1.2
Total Control 1000 : TCS 3.3
Total Control 1000 : SS7
Total Control 1000 : TCS 3.5
Total Control 1000 : TCS 4.0

Search Terms: mpip

Documentation Type:


Access  File Name  Size     Released  Description
No matching items were found.


-----Original Message-----
[mailto:[e-mail]]On Behalf Of Jeff Mcadams
Sent: Wednesday, December 20, 2000 10:46 AM


Also sprach Brian Becker
>How do you set up two chassis to work together in establishing an MPPP
>connection?

Check out the manuals (pdf's availabe, even without a service contract,
at totalservice.3com.com) for info on MPIP.  MPIP is the coordination
protocol that Arcs use to do multi-chassis multi-link.  Be aware that
you'll need the time syncronized between the Arcs...but that's easily
done since they support NTP.  :)
--
Jeff McAdams                            Email: [e-mail]
Head Network Administrator              Voice: [phone]
IgLou Internet Services                        [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Campbell Simpson" <[e-mail]>
Subject: Re: (usr-tc) Settings?
Date: 21 Dec 2000 16:29:23 +1300

You need to look at the RADIUS attribute "NAS-Port-Type" if its "Async"
then you know its a modem connection. You'll need to set up your RADIUS
server to differentiate on the value of this attribute.

Campbell

>>> [e-mail] 12/21/00 05:20 >>>
I'm using a TC with HiperDSPs and authenticating with RadiusNT in ODBC
mode.  I need to be able to control concurrent logins and allow logins
based on type of connection, i.e. ISDN or analog.  Can someone tell me
what changes I need to make on the TC?

Thanks,

Steve Cobb

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.



-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jim Johnson <[e-mail]>
Subject: (usr-tc) RESEND: Problems with relocating modems to a new telco
Date: 21 Dec 2000 08:56:13 -0500


We are relocating our modems to a new telco provider's colocation space.

We grabbed an old quad chassis for testing the new colo site before the
move.

The quads are running 6.1.6 code and the Dual PRI card is running the
3.1.5 code.

The telco vendor is running Nortel DMS-100 switches.

Most of our testing is working fine, but we are having problems with
some callers who can connect fine to our old POP and not at all to the
new POP.

I have this connection problem myself when I test the new pop from my
home using a USR 56K modem.  I can connect to the new pop at v.34, but
not at v.90.  When I remove error correction on the modem and use
Hyperterm, I do see a lot of line noise.

I also had the telco terminate one of the PRI's we are testing in their
Cisco NAS box, and I could connect fine into that box from my home at
v.90 or v.34.

This is really confusing me.

I was wondering if the 6.1.86 quad modem code might help, but I can't
access it from the total control site even though it has no new
features, just bug fixes.  (This annoys me since we paid 100K for the
four chassis we still own).

Anyway, I was wondering if anyone could help me.  Obviously, I don't
want to switch thousands of users to the new pop until I understand what
is happening.

If anyone from 3com is montioring the list anymore, maybe you will help
with a MIME attachment.....

TIA,

Jim

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "G. Douglas Davidson" <[e-mail]>
Subject: (usr-tc) DMS-500 and NI-2 Problems
Date: 21 Dec 2000 11:19:18 -0500

We are in the process of setting up some new PRIs and things ain't going so
well.  We have to use the NI-2 interface, as it seems to be the only one
supported by the CLEC.  Everything looks just swell on this side, yet we are
getting "all circuits busy" when we attempt to use the lines.

Turned off service messaging as per one of the list suggestions.  Running DSP
2.1.9.  D-Channel is up.  Things look good.

Thanks for any suggestions.

span1> dis atstat

Tslot  Status   Modem    Status        Call ID        Action    Q931
               Connect Srvc State                     Queued    Ref
 01      Idle    N/A          IS      0x00000000        NONE    0x00000000
...
 23      Idle    N/A          IS      0x00000000        NONE    0x00000000
 24     Dchan    N/A          IS      0x00000000        NONE    0x00000000

span1> dis ccrcfig
  Span1 Configured Signal Mode is (sigmode): MESSAGE ORIENTED
  Span1 Signal Mode Active is:               MESSAGE ORIENTED
  Span1 DNIS Enable is (dnisena):            DNIS ADDRESS
  Span1 Dial Out Address Delay (doadrdly):   70 ms
  Span1 Configured Switch Type is (swtype):  NI2
  Span1 Idle Byte is (idlebyte):             0xFE
  Span1 Ana Calls Blocked Err Code (ancbec): 58
  Span1 Digi Calls Blocked Err Code (dcbec): 58
  Span1 No IGWS Avail Err Code (noigwsav):   58
  Span1 Chan Blocked Err Code (chanblck):    58
  Span1 Block Call Type is (blcaltyp):       BLOCK NONE
  Span1 Tone Type is (tonetype):             DTMF TONE
  Span1 Number Of DTMF Tones is (numdtmft):  4
  Span1 Dial Out Select Direction (dseldir): DOWN
  Span1 Dial Out Next Timeslot (dntslot):    24
  Span1 Alert Message Mode (alrtmsg):        ALRT MSG MODE DISABLED
  Span1 CALL PROC Message Mode (cprocmsg):   CALLPROC MSG MODE ENABLED
  Span1 Overlap Receiving Mode (ovrrxmode):  OVERLAP RECEIVE MODE DISABLED
  Span1 Timeout between INFO msg(inftmout):  12
  Span1 Total Number of Digits (inbdnisln):  12
  Span1 Signaling Group Type is:             FAS
  Span1 Configured SS7 signal mode is:       None
  Span1 active SS7 signal mode is:           None

span1> dis spnstats
   Span1 Near Time Elapsed is:               653 seconds
   Span1 Near Valid Intervals is:            69
   Span1 Line Status is:
      NO ALARM          = TRUE
      RCV FAR END LOF   = FALSE
      XMT FAR END LOF   = FALSE
      RCV AIS           = FALSE
      XMT AIS           = FALSE
      OUT OF FRAME      = FALSE
      LOSS OF SIGNAL    = FALSE
      LOOPBACK STATE    = FALSE
      T16 AIS           = FALSE
      RCV FAR END LOMF  = FALSE
      XMT FAR END LOMF  = FALSE
      RCV TEST CODE     = FALSE
      OTHER FAILURE     = FALSE
   Span1 Send Code is:                        SEND NO CODE
   Span1 dsx1 Loopback Configuration is:      NO LOOP
   Span1 Receiver Gain is:                    0.0 dB GAIN   (2.9 dB Steps)
   Span1 Continuous CRC Error is:             FALSE
   Span1 Physical State is:                   F1 OPERATIONAL
   Span1 Loopback Init Originate is:          NONE
   Span1 Modem Not Available Count is:        0
   Span1 Invalid Bearer Capability Count is:  0
   Span1 Invalid Channel ID Count is:         0
   Span1 Invalid Progress Indicator Count is: 0
   Span1 Invalid Calling Party Count is:      0
   Span1 Invalid Called Party Count is:       0
   Span1 Call Block Failure Count is:         0
   Span1 No Ring Off Failure Count is:        0
   Span1 Telco Disconnect Failure Count is:   0
   Span1 TELCO Failed To Wink Count is:       0
   Span1 TELCO Wink Too Short Count is:       0
   Span1 No Channel Available Count is:       0
   Span1 Dial In No Resp To Disc Count is:    0
   Span1 Dial Out No Resp To Disc Count is:   0
   Span1 Gnd Start No Resp To Disc Count is:  0
   Span1 Switch Type Active is:              NI2
   Span1 D-channel Operational is:           UP
   Span1 Signal Mode Active is:              MESSAGE ORIENTED
   Span1 Service Messages Sent:               0
   Span1 Service Ack Messages Received:       0

--
-----
G Douglas Davidson                      | CityNet, Inc.
[e-mail]                    | Pittsburgh, PA
voice: 412.481.5406                     | fax: [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jim Johnson <[e-mail]>
Subject: Re: (usr-tc) DMS-500 and NI-2 Problems
Date: 21 Dec 2000 11:21:14 -0500


We are setting up a new POP and ran into that same problem initially.

I'll bet if you use TCM and issue the command "Local In Service" to the
PRI card, the calls will start coming in.

There is a setting in the DMS-500 switch to "emulate" an AT&T switch.
This will cause the D-Channels to come up properly when you reset the
card.  The phone company needs to set this for you.

I hate switching telcos...

Regards,

Jim

"G. Douglas Davidson" wrote:
>
> We are in the process of setting up some new PRIs and things ain't going so
> well.  We have to use the NI-2 interface, as it seems to be the only one
> supported by the CLEC.  Everything looks just swell on this side, yet we are
> getting "all circuits busy" when we attempt to use the lines.
>
> Turned off service messaging as per one of the list suggestions.  Running DSP
> 2.1.9.  D-Channel is up.  Things look good.
>
> Thanks for any suggestions.
>
> span1> dis atstat
>
> Tslot  Status   Modem    Status        Call ID        Action    Q931
>                Connect Srvc State                     Queued    Ref
>  01      Idle    N/A          IS      0x00000000        NONE    0x00000000
> ...
>  23      Idle    N/A          IS      0x00000000        NONE    0x00000000
>  24     Dchan    N/A          IS      0x00000000        NONE    0x00000000
>
> span1> dis ccrcfig
>   Span1 Configured Signal Mode is (sigmode): MESSAGE ORIENTED
>   Span1 Signal Mode Active is:               MESSAGE ORIENTED
>   Span1 DNIS Enable is (dnisena):            DNIS ADDRESS
>   Span1 Dial Out Address Delay (doadrdly):   70 ms
>   Span1 Configured Switch Type is (swtype):  NI2
>   Span1 Idle Byte is (idlebyte):             0xFE
>   Span1 Ana Calls Blocked Err Code (ancbec): 58
>   Span1 Digi Calls Blocked Err Code (dcbec): 58
>   Span1 No IGWS Avail Err Code (noigwsav):   58
>   Span1 Chan Blocked Err Code (chanblck):    58
>   Span1 Block Call Type is (blcaltyp):       BLOCK NONE
>   Span1 Tone Type is (tonetype):             DTMF TONE
>   Span1 Number Of DTMF Tones is (numdtmft):  4
>   Span1 Dial Out Select Direction (dseldir): DOWN
>   Span1 Dial Out Next Timeslot (dntslot):    24
>   Span1 Alert Message Mode (alrtmsg):        ALRT MSG MODE DISABLED
>   Span1 CALL PROC Message Mode (cprocmsg):   CALLPROC MSG MODE ENABLED
>   Span1 Overlap Receiving Mode (ovrrxmode):  OVERLAP RECEIVE MODE DISABLED
>   Span1 Timeout between INFO msg(inftmout):  12
>   Span1 Total Number of Digits (inbdnisln):  12
>   Span1 Signaling Group Type is:             FAS
>   Span1 Configured SS7 signal mode is:       None
>   Span1 active SS7 signal mode is:           None
>
> span1> dis spnstats
>    Span1 Near Time Elapsed is:               653 seconds
>    Span1 Near Valid Intervals is:            69
>    Span1 Line Status is:
>       NO ALARM          = TRUE
>       RCV FAR END LOF   = FALSE
>       XMT FAR END LOF   = FALSE
>       RCV AIS           = FALSE
>       XMT AIS           = FALSE
>       OUT OF FRAME      = FALSE
>       LOSS OF SIGNAL    = FALSE
>       LOOPBACK STATE    = FALSE
>       T16 AIS           = FALSE
>       RCV FAR END LOMF  = FALSE
>       XMT FAR END LOMF  = FALSE
>       RCV TEST CODE     = FALSE
>       OTHER FAILURE     = FALSE
>    Span1 Send Code is:                        SEND NO CODE
>    Span1 dsx1 Loopback Configuration is:      NO LOOP
>    Span1 Receiver Gain is:                    0.0 dB GAIN   (2.9 dB Steps)
>    Span1 Continuous CRC Error is:             FALSE
>    Span1 Physical State is:                   F1 OPERATIONAL
>    Span1 Loopback Init Originate is:          NONE
>    Span1 Modem Not Available Count is:        0
>    Span1 Invalid Bearer Capability Count is:  0
>    Span1 Invalid Channel ID Count is:         0
>    Span1 Invalid Progress Indicator Count is: 0
>    Span1 Invalid Calling Party Count is:      0
>    Span1 Invalid Called Party Count is:       0
>    Span1 Call Block Failure Count is:         0
>    Span1 No Ring Off Failure Count is:        0
>    Span1 Telco Disconnect Failure Count is:   0
>    Span1 TELCO Failed To Wink Count is:       0
>    Span1 TELCO Wink Too Short Count is:       0
>    Span1 No Channel Available Count is:       0
>    Span1 Dial In No Resp To Disc Count is:    0
>    Span1 Dial Out No Resp To Disc Count is:   0
>    Span1 Gnd Start No Resp To Disc Count is:  0
>    Span1 Switch Type Active is:              NI2
>    Span1 D-channel Operational is:           UP
>    Span1 Signal Mode Active is:              MESSAGE ORIENTED
>    Span1 Service Messages Sent:               0
>    Span1 Service Ack Messages Received:       0
>
> --
> -----
> G Douglas Davidson                      | CityNet, Inc.
> [e-mail]                    | Pittsburgh, PA
> voice: 412.481.5406                     | fax: [phone]
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "G. Douglas Davidson" <[e-mail]>
Subject: Re: (usr-tc) DMS-500 and NI-2 Problems
Date: 21 Dec 2000 11:48:57 -0500

On Dec 21, 11:21am, Jim Johnson wrote:
> Subject: Re: (usr-tc) DMS-500 and NI-2 Problems
>
> We are setting up a new POP and ran into that same problem initially.
>
> I'll bet if you use TCM and issue the command "Local In Service" to the
> PRI card, the calls will start coming in.
>
> There is a setting in the DMS-500 switch to "emulate" an AT&T switch.
> This will cause the D-Channels to come up properly when you reset the
> card.  The phone company needs to set this for you.
>
> I hate switching telcos...

Thanks for the pointer.  I went ahead and issued Local In Service, with and
without Service Messages, in TCM and in command line on the DSP and I am still
having issues, but that sort of makes sense since NI-2 does not support service
messages.  I have emailed the telco to have them set up the emulation though
(or try to have them do it.)  With this emulation in place, are you still using
NI-2 or can you then set things up to use an AT&T 5ess?

Thanks again!

>
> Regards,
>
> Jim
>
> "G. Douglas Davidson" wrote:
> >
> > We are in the process of setting up some new PRIs and things ain't going so
> > well.  We have to use the NI-2 interface, as it seems to be the only one
> > supported by the CLEC.  Everything looks just swell on this side, yet we
are
> > getting "all circuits busy" when we attempt to use the lines.
> >
> > Turned off service messaging as per one of the list suggestions.  Running
DSP
> > 2.1.9.  D-Channel is up.  Things look good.
> >
> > Thanks for any suggestions.
> >
> > span1> dis atstat
> >
> > Tslot  Status   Modem    Status        Call ID        Action    Q931
> >                Connect Srvc State                     Queued    Ref
> >  01      Idle    N/A          IS      0x00000000        NONE    0x00000000
> > ...
> >  23      Idle    N/A          IS      0x00000000        NONE    0x00000000
> >  24     Dchan    N/A          IS      0x00000000        NONE    0x00000000
> >
> > span1> dis ccrcfig
> >   Span1 Configured Signal Mode is (sigmode): MESSAGE ORIENTED
> >   Span1 Signal Mode Active is:               MESSAGE ORIENTED
> >   Span1 DNIS Enable is (dnisena):            DNIS ADDRESS
> >   Span1 Dial Out Address Delay (doadrdly):   70 ms
> >   Span1 Configured Switch Type is (swtype):  NI2
> >   Span1 Idle Byte is (idlebyte):             0xFE
> >   Span1 Ana Calls Blocked Err Code (ancbec): 58
> >   Span1 Digi Calls Blocked Err Code (dcbec): 58
> >   Span1 No IGWS Avail Err Code (noigwsav):   58
> >   Span1 Chan Blocked Err Code (chanblck):    58
> >   Span1 Block Call Type is (blcaltyp):       BLOCK NONE
> >   Span1 Tone Type is (tonetype):             DTMF TONE
> >   Span1 Number Of DTMF Tones is (numdtmft):  4
> >   Span1 Dial Out Select Direction (dseldir): DOWN
> >   Span1 Dial Out Next Timeslot (dntslot):    24
> >   Span1 Alert Message Mode (alrtmsg):        ALRT MSG MODE DISABLED
> >   Span1 CALL PROC Message Mode (cprocmsg):   CALLPROC MSG MODE ENABLED
> >   Span1 Overlap Receiving Mode (ovrrxmode):  OVERLAP RECEIVE MODE DISABLED
> >   Span1 Timeout between INFO msg(inftmout):  12
> >   Span1 Total Number of Digits (inbdnisln):  12
> >   Span1 Signaling Group Type is:             FAS
> >   Span1 Configured SS7 signal mode is:       None
> >   Span1 active SS7 signal mode is:           None
> >
> > span1> dis spnstats
> >    Span1 Near Time Elapsed is:               653 seconds
> >    Span1 Near Valid Intervals is:            69
> >    Span1 Line Status is:
> >       NO ALARM          = TRUE
> >       RCV FAR END LOF   = FALSE
> >       XMT FAR END LOF   = FALSE
> >       RCV AIS           = FALSE
> >       XMT AIS           = FALSE
> >       OUT OF FRAME      = FALSE
> >       LOSS OF SIGNAL    = FALSE
> >       LOOPBACK STATE    = FALSE
> >       T16 AIS           = FALSE
> >       RCV FAR END LOMF  = FALSE
> >       XMT FAR END LOMF  = FALSE
> >       RCV TEST CODE     = FALSE
> >       OTHER FAILURE     = FALSE
> >    Span1 Send Code is:                        SEND NO CODE
> >    Span1 dsx1 Loopback Configuration is:      NO LOOP
> >    Span1 Receiver Gain is:                    0.0 dB GAIN   (2.9 dB Steps)
> >    Span1 Continuous CRC Error is:             FALSE
> >    Span1 Physical State is:                   F1 OPERATIONAL
> >    Span1 Loopback Init Originate is:          NONE
> >    Span1 Modem Not Available Count is:        0
> >    Span1 Invalid Bearer Capability Count is:  0
> >    Span1 Invalid Channel ID Count is:         0
> >    Span1 Invalid Progress Indicator Count is: 0
> >    Span1 Invalid Calling Party Count is:      0
> >    Span1 Invalid Called Party Count is:       0
> >    Span1 Call Block Failure Count is:         0
> >    Span1 No Ring Off Failure Count is:        0
> >    Span1 Telco Disconnect Failure Count is:   0
> >    Span1 TELCO Failed To Wink Count is:       0
> >    Span1 TELCO Wink Too Short Count is:       0
> >    Span1 No Channel Available Count is:       0
> >    Span1 Dial In No Resp To Disc Count is:    0
> >    Span1 Dial Out No Resp To Disc Count is:   0
> >    Span1 Gnd Start No Resp To Disc Count is:  0
> >    Span1 Switch Type Active is:              NI2
> >    Span1 D-channel Operational is:           UP
> >    Span1 Signal Mode Active is:              MESSAGE ORIENTED
> >    Span1 Service Messages Sent:               0
> >    Span1 Service Ack Messages Received:       0
> >
> > --
> > -----
> > G Douglas Davidson                      | CityNet, Inc.
> > [e-mail]                    | Pittsburgh, PA
> > voice: 412.481.5406                     | fax: [phone]
> >
> > -
> >  To unsubscribe to usr-tc, send an email to "[e-mail]"
> >  with "unsubscribe usr-tc" in the body of the message.
> >  For information on digests or retrieving files and old messages send
> >  "help" to the same address.  Do not use quotes in your message.
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>-- End of excerpt from Jim Johnson



--
-----
G Douglas Davidson                      | CityNet, Inc.
[e-mail]                    | Pittsburgh, PA
voice: 412.481.5406                     | fax: [phone]

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Monkhouse" <[e-mail]>
Subject: RE: (usr-tc) RESEND: Problems with relocating modems to a new telco
Date: 22 Dec 2000 07:43:29 +1000

Is the x2/v90 feature set enabled on your NMC ?


-----Original Message-----
[mailto:[e-mail]]On Behalf Of Jim Johnson
Sent: Thursday, December 21, 2000 11:56 PM



We are relocating our modems to a new telco provider's colocation space.

We grabbed an old quad chassis for testing the new colo site before the
move.

The quads are running 6.1.6 code and the Dual PRI card is running the
3.1.5 code.

The telco vendor is running Nortel DMS-100 switches.

Most of our testing is working fine, but we are having problems with
some callers who can connect fine to our old POP and not at all to the
new POP.

I have this connection problem myself when I test the new pop from my
home using a USR 56K modem.  I can connect to the new pop at v.34, but
not at v.90.  When I remove error correction on the modem and use
Hyperterm, I do see a lot of line noise.

I also had the telco terminate one of the PRI's we are testing in their
Cisco NAS box, and I could connect fine into that box from my home at
v.90 or v.34.

This is really confusing me.

I was wondering if the 6.1.86 quad modem code might help, but I can't
access it from the total control site even though it has no new
features, just bug fixes.  (This annoys me since we paid 100K for the
four chassis we still own).

Anyway, I was wondering if anyone could help me.  Obviously, I don't
want to switch thousands of users to the new pop until I understand what
is happening.

If anyone from 3com is montioring the list anymore, maybe you will help
with a MIME attachment.....

TIA,

Jim

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: (usr-tc) FS: **NEW** Hiper DSP and bundles, Refurb DSP, ARC, NMC..ect
Date: 21 Dec 2000 17:03:27 -0500

Happy Holidays Guys,

I have These NEW Hiper DSP cards available. They are New in box with
factory warranty. Hence the Term NEW.
Asking $3700.00 per set

I also have the ** NEW ** 3Com 1000 ISP Bundles ** NEW **
Priced to compete with the 3Com's best tiered distributors.

I also have refurbished :
Hiper Bundles $8500

Hiper DSP sets at $3000 (T1 version)
Hiper ARC's $1700.00
Hiper NMC's $1000.00
EdgeServer $1000.00

Also have 15 - Quad Bundles.....looking to move :0

I am also working on information and availability on the New and Upcoming
HD96 port modem cards.

Try me for all your Total Control Needs....manuals, parts, quad equipment,
cables..ect


Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Jim Johnson <[e-mail]>
Subject: Re: (usr-tc) RESEND: Problems with relocating modems to a new telco
Date: 21 Dec 2000 17:09:50 -0500


Yes we have x2/v.90 on the NMC.

Jim



Steve Monkhouse wrote:
>
> Is the x2/v90 feature set enabled on your NMC ?
>
> -----Original Message-----
> From: [e-mail]
> [mailto:[e-mail]]On Behalf Of Jim Johnson
> Sent: Thursday, December 21, 2000 11:56 PM
> To: usr-tc
> Subject: (usr-tc) RESEND: Problems with relocating modems to a new telco
>
> We are relocating our modems to a new telco provider's colocation space.
>
> We grabbed an old quad chassis for testing the new colo site before the
> move.
>
> The quads are running 6.1.6 code and the Dual PRI card is running the
> 3.1.5 code.
>
> The telco vendor is running Nortel DMS-100 switches.
>
> Most of our testing is working fine, but we are having problems with
> some callers who can connect fine to our old POP and not at all to the
> new POP.
>
> I have this connection problem myself when I test the new pop from my
> home using a USR 56K modem.  I can connect to the new pop at v.34, but
> not at v.90.  When I remove error correction on the modem and use
> Hyperterm, I do see a lot of line noise.
>
> I also had the telco terminate one of the PRI's we are testing in their
> Cisco NAS box, and I could connect fine into that box from my home at
> v.90 or v.34.
>
> This is really confusing me.
>
> I was wondering if the 6.1.86 quad modem code might help, but I can't
> access it from the total control site even though it has no new
> features, just bug fixes.  (This annoys me since we paid 100K for the
> four chassis we still own).
>
> Anyway, I was wondering if anyone could help me.  Obviously, I don't
> want to switch thousands of users to the new pop until I understand what
> is happening.
>
> If anyone from 3com is montioring the list anymore, maybe you will help
> with a MIME attachment.....
>
> TIA,
>
> Jim
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.

-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: [e-mail]
Subject: (usr-tc) Using T1 and Quads with PRI
Date: 22 Dec 2000 12:32:07 -0500 (EST)

Hello,

For years we've been using a Dual T1 Card and some quad modems with CT1
lines.  I always assumed we could also use these with PRI, but now that
we've got some PRI's to try it with, I can't get it to work...  Is there a
magic setting to change in TCM somewhere I'm not aware of?  The modem's
line interface source should clearly be priT1dm, but I feel like I'm
missing a setting on the T1 card to match....

Who wants to tell me how foolish I'm being?  Thanks!

David Ernst
HoosierNet, Inc.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Chad Schwartz <[e-mail]>
Subject: Re: (usr-tc) Using T1 and Quads with PRI
Date: 22 Dec 2000 11:44:21 -0600 (CST)

Heh. I can tell you right now what the problem is.

There are 2 different firmware images for the dual PRI/CT1 NAC. 1 for
PRI, 1 for CT1.

Are you making sure to load the PRI firmware to the card?

Chad

On Fri, 22 Dec 2000 [e-mail] wrote:

> Hello,
>
> For years we've been using a Dual T1 Card and some quad modems with CT1
> lines.  I always assumed we could also use these with PRI, but now that
> we've got some PRI's to try it with, I can't get it to work...  Is there a
> magic setting to change in TCM somewhere I'm not aware of?  The modem's
> line interface source should clearly be priT1dm, but I feel like I'm
> missing a setting on the T1 card to match....
>
> Who wants to tell me how foolish I'm being?  Thanks!
>
> David Ernst
> HoosierNet, Inc.
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: [e-mail]
Subject: Re: (usr-tc) Using T1 and Quads with PRI
Date: 22 Dec 2000 13:11:48 -0500 (EST)

>Heh. I can tell you right now what the problem is.
>
>There are 2 different firmware images for the dual PRI/CT1 NAC. 1 for
>PRI, 1 for CT1.
>
>Are you making sure to load the PRI firmware to the card?

Uh, I'm making sure to do it right now!  :)

Thanks...  I'm sure that was stated somewhere very clearly in the
documentation somewhere, but I have no doubt that your answer was much
faster than me pouring through it.  Time savings, what a wonderful
holiday gift!

David


>Chad
>
>On Fri, 22 Dec 2000 [e-mail] wrote:
>
>> Hello,
>>
>> For years we've been using a Dual T1 Card and some quad modems with CT1
>> lines.  I always assumed we could also use these with PRI, but now that
>> we've got some PRI's to try it with, I can't get it to work...  Is there a
>> magic setting to change in TCM somewhere I'm not aware of?  The modem's
>> line interface source should clearly be priT1dm, but I feel like I'm
>> missing a setting on the T1 card to match....
>>
>> Who wants to tell me how foolish I'm being?  Thanks!
>>
>> David Ernst
>> HoosierNet, Inc.
>>
>>
>> -
>>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>>  with "unsubscribe usr-tc" in the body of the message.
>>  For information on digests or retrieving files and old messages send
>>  "help" to the same address.  Do not use quotes in your message.
>>
>
>
>-
> To unsubscribe to usr-tc, send an email to "[e-mail]"
> with "unsubscribe usr-tc" in the body of the message.
> For information on digests or retrieving files and old messages send
> "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Chad Schwartz <[e-mail]>
Subject: Re: (usr-tc) Using T1 and Quads with PRI
Date: 22 Dec 2000 12:52:05 -0600 (CST)

> Uh, I'm making sure to do it right now!  :)

hehehe. Good. PRI's have quite a bit more configuration stuff that you
have to do - than CT1's. For instance, switch type, alaw/ulaw, ANI/DNIS
(many telcos do not configure ANI/DNIS for CT1's - altho from what i
understand, they CAN.  GTE CyberDS1 CT1's get delivered with DNIS turned
on, but 0 digits sent. :/ ), and a few other things I'm not aware of, as I
don't use PRI's.

 > > Thanks...  I'm sure that was stated somewhere
> very clearly in the
> documentation somewhere, but I have no doubt that your answer was much
> faster than me pouring through it.  Time savings, what a wonderful
> holiday gift!

Hahaha.  Yeah. It is in the docs. No big deal though.  If you've never
dealt with PRI's before, its an easy stumble.

Happy holidays! ;)

Chad

>
> David
>
>
> >Chad
> >
> >On Fri, 22 Dec 2000 [e-mail] wrote:
> >
> >> Hello,
> >>
> >> For years we've been using a Dual T1 Card and some quad modems with CT1
> >> lines.  I always assumed we could also use these with PRI, but now that
> >> we've got some PRI's to try it with, I can't get it to work...  Is there a
> >> magic setting to change in TCM somewhere I'm not aware of?  The modem's
> >> line interface source should clearly be priT1dm, but I feel like I'm
> >> missing a setting on the T1 card to match....
> >>
> >> Who wants to tell me how foolish I'm being?  Thanks!
> >>
> >> David Ernst
> >> HoosierNet, Inc.
> >>
> >>
> >> -
> >>  To unsubscribe to usr-tc, send an email to "[e-mail]"
> >>  with "unsubscribe usr-tc" in the body of the message.
> >>  For information on digests or retrieving files and old messages send
> >>  "help" to the same address.  Do not use quotes in your message.
> >>
> >
> >
> >-
> > To unsubscribe to usr-tc, send an email to "[e-mail]"
> > with "unsubscribe usr-tc" in the body of the message.
> > For information on digests or retrieving files and old messages send
> > "help" to the same address.  Do not use quotes in your message.
> >
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Lists <[e-mail]>
Subject: (usr-tc) NMC chassis alarm LED
Date: 23 Dec 2000 20:12:15 +1100 (EST)


Does anyone know of an easy way to read the status of the NMC chassis
alarm LED?

Ideally a simple read that returned an integer indicating the LED colour.

So far I've been unable to find an object that didn't require a lot of
parsing.  Any ideas?



-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Stephen Amadei <[e-mail]>
Subject: Re: (usr-tc) NMC chassis alarm LED
Date: 23 Dec 2000 04:55:41 -0500 (EST)

On Sat, 23 Dec 2000, Lists wrote:

> Does anyone know of an easy way to read the status of the NMC chassis
> alarm LED?
>
> Ideally a simple read that returned an integer indicating the LED colour.
>
> So far I've been unable to find an object that didn't require a lot of
> parsing.  Any ideas?

How well can you read Perl?  If you can, download my TCView script... it
reads the LEDs off the TC and makes gif files suitable for putting on a
webpage.  With a bit of coding, you could add a routine to email/notify
you when certain LEDs change colors.  If you did this, send me the code
and I'll integrate it into the script.

Script at http://www.dandy.net/~amadei.  TCView 0.93n is the current
version.

                    ----Steve
Stephen Amadei
Dandy.net CTO
Atlantic City, NJ



-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Mike Andrews <[e-mail]>
Subject: Re: (usr-tc) NMC chassis alarm LED
Date: 26 Dec 2000 07:36:15 -0500 (EST)

If all you want is the NMC alarm LED, get OID 1.3.6.1.4.1.429.1.2.2.12
and you'll get:

1 = No alarm
2 = Temperature High
3 = Fan Failure
4 = Voltage Warning for PSU
5 = Failure of PSU
6 = Management Bus Failure
7 = Interface Card Failure
8 = Incompatible Token-Ring NIC (eww yuk!)



Mike Andrews * [e-mail] * [e-mail] * http://www.bit0.com
VP, sysadmin, & network guy, Digital Crescent Inc, Frankfort KY
Internet access for Frankfort, Lexington, Louisville and surrounding counties

www.fark.com: If it's not news, it's Fark.  (Or something like that.)

On Sat, 23 Dec 2000, Stephen Amadei wrote:

> On Sat, 23 Dec 2000, Lists wrote:
>
> > Does anyone know of an easy way to read the status of the NMC chassis
> > alarm LED?
> >
> > Ideally a simple read that returned an integer indicating the LED colour.
> >
> > So far I've been unable to find an object that didn't require a lot of
> > parsing.  Any ideas?
>
> How well can you read Perl?  If you can, download my TCView script... it
> reads the LEDs off the TC and makes gif files suitable for putting on a
> webpage.  With a bit of coding, you could add a routine to email/notify
> you when certain LEDs change colors.  If you did this, send me the code
> and I'll integrate it into the script.
>
> Script at http://www.dandy.net/~amadei.  TCView 0.93n is the current
> version.
>
>                     ----Steve
> Stephen Amadei
> Dandy.net CTO
> Atlantic City, NJ
>
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Steve Rivera -www.wrca.net" <[e-mail]>
Subject: (usr-tc) FS: USR/3Com Hiper Edgserver Bundle and cards.
Date: 26 Dec 2000 12:10:30 -0500

WR Communication Associates has the following USR/3Com Hardware available:

1- High Density Chassis w/ single 70A power
1- EdgeServer with Scsi and Ethernet nic
1- Hiper NMC
1- Hiper ARC
2- Hiper DSP

w/ edgserver ...asking $8500.
without edgserver ...Asking $7750.

Also have individual cards like:
Hiper NMC
Hiper ARC
Hiper DSP
Quad Digital Modems
Quad Analog Modems
NMC
Netserver PRI
Dual PRI/T1
Dual PRI/E1
Dual T1/E1


Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
(www.isp-networkhardware.com)
Email: [e-mail] - Mobile Email: [e-mail]

Worldwide Provider of Network Hardware Since 1981.













-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Antonio Querubin <[e-mail]>
Subject: (usr-tc) recommendation for sources of HiPER ARC card
Date: 26 Dec 2000 07:48:09 -1000 (HST)

I'm looking for recommendations on sources for a HiPER ARC router card,
preferably new but good used condition is also acceptable.  Anybody got
any particular favorite suppliers?  If so please email me in private.
Thanks.

Antonio Querubin
[e-mail]


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: [e-mail]
Subject: (usr-tc) TC1000 For Sale
Date: 26 Dec 2000 12:25:01 -0600


Happy Holidays Everyone!  I've got one populated TC1000 for sale in
EXCELLENT condition.  Here's the specs:

12 - Quad v.34 Digital Modems
1 - Dual PRI NAC
1 - Netserver PRI
1 - NMC
1 - Ethernet NIC
1 - High Speed WAN/Ethernet NIC Console
1 - Dual T1/DS-1 NIC
2 - 70A Power Supplies

UNIT IS IN EXCELLENT CONDITION!  CONTACT OFF-LIST FOR PICTURES.

$2,000 + Actual Shipping (Your preferred method)

Josh Sargent
[e-mail]


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Lists <[e-mail]>
Subject: Re: (usr-tc) NMC chassis alarm LED
Date: 27 Dec 2000 13:31:11 +1100 (EST)


> If all you want is the NMC alarm LED, get OID 1.3.6.1.4.1.429.1.2.2.12
> and you'll get:
>
> 1 = No alarm
> 2 = Temperature High
> 3 = Fan Failure
> 4 = Voltage Warning for PSU
> 5 = Failure of PSU
> 6 = Management Bus Failure
> 7 = Interface Card Failure
> 8 = Incompatible Token-Ring NIC (eww yuk!)

Yeah, saw that.  This seems (guessing) to give the cause of the last
failure though, not the current state (ie, even after the failure has
passed, it remains set).

In our case, every chassis says "Fan Failure", although none of the fans
have failed.


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "ddns" <[e-mail]>
Subject: Re: (usr-tc) FS: Quad Bundles ...Super Cheap...Hiper..
Date: 27 Dec 2000 14:35:40 +1100

We have shut down our ISP dial in business and we have the following to
sell.
3 com total control unit
hiper dsp card
hiper access router card
hipernmc
acu 130 amp
less than 12 months old
little work
located in Aust
Rod
-----Original Message-----


>Hello Folks, This might sound too good to be true but it is :) They are
>configured as follows. Don't be hesitant because of price. They are in
>great cosmetic and functional condition. I bought them at a great price and
>since it is the giving season I though I could pass the savings to this
list :)
>
>I am always open to opportunity so if you need help with pricing and your a
>serious buyer. I will work with you.
>Be sure to mention you found it on the USR List.
>
>HD Chassis with Single 70A Power
>NMC
>Netserver PRI
>Dual PRI
>12 Quad Digital Modems
>
>1-5 $2000
>6-10 $1750
>11-15 $1500
>
>Hiper DSP $3000
>Hiper ARC $2000
>Hiper NMC $1000
>Dual PRI/E1 $650...Hard to Find
>
>As usual I guarantee all equipment working.
>
>If you are looking anything USR/3Com Total Control, Netservers, MP, MMP's,
>nic,macs, parts ect.
>YEAH I GOT THAT :)
>
>Steve Rivera (VP) - w-732.833.2111 x102 /  c-732.433.5890 24Hr
>(www.isp-networkhardware.com)
>Email: [e-mail] - Mobile Email: [e-mail]
>
>Worldwide Provider of Network Hardware Since 1981.
>
>
>
>
>
>
>
>
>
>
>
>
>
>-
> To unsubscribe to usr-tc, send an email to "[e-mail]"
> with "unsubscribe usr-tc" in the body of the message.
> For information on digests or retrieving files and old messages send
> "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Scott Kupferschmidt <[e-mail]>
Subject: (usr-tc) RADIUS question
Date: 28 Dec 2000 20:05:42 -0600 (CST)

Hey guys.  I have a question regarding RADIUS servers in general.  Right
now we're using Cistron RADIUS on our main authentication server, works
great and all but we're trying to set up a backup RADIUS server as well.

That part isn't hard (setting it up) except I don't know what the
configuration settings are to make it authenticate off of a different
file, not just the system password file.

Any ideas?  Thanks.

Scott


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Paul Farber <[e-mail]>
Subject: Re: (usr-tc) RADIUS question
Date: 28 Dec 2000 21:25:50 -0500 (EST)

It's under AUTH-TYPE

System = system files
'password' = put the password in quotes, plain text
others you may have compiled in (cdb, SQL)

Paul Farber
Farber Technology
[e-mail]
Ph  570-628-5303
Fax [phone]

On Thu, 28 Dec 2000, Scott Kupferschmidt wrote:

> Hey guys.  I have a question regarding RADIUS servers in general.  Right
> now we're using Cistron RADIUS on our main authentication server, works
> great and all but we're trying to set up a backup RADIUS server as well.
>
> That part isn't hard (setting it up) except I don't know what the
> configuration settings are to make it authenticate off of a different
> file, not just the system password file.
>
> Any ideas?  Thanks.
>
> Scott
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Scott Kupferschmidt <[e-mail]>
Subject: Re: (usr-tc) RADIUS question
Date: 28 Dec 2000 21:09:18 -0600 (CST)

Paul-

Regarding what you said, that isn't what I asked. :-)
Right now RADIUS is authenticating off of /etc/master.passwd in FreeBSD,
and basically what we are doing is copying that file every 5 minutes to
another server (radius.passwd is the name).

On that other server I want the RADIUS daemon to authenticate off of
radius.passwd and not /etc/master.passwd -- How do I do this?

Unless I'm getting the wrong idea, and you're saying I have to put in
"System = /etc/raddb/radius.passwd" ???

Scott


On Thu, 28 Dec 2000, Paul Farber wrote:

> It's under AUTH-TYPE
>
> System = system files
> 'password' = put the password in quotes, plain text
> others you may have compiled in (cdb, SQL)
>
> Paul Farber
> Farber Technology
> [e-mail]
> Ph  570-628-5303
> Fax [phone]
>
> On Thu, 28 Dec 2000, Scott Kupferschmidt wrote:
>
> > Hey guys.  I have a question regarding RADIUS servers in general.  Right
> > now we're using Cistron RADIUS on our main authentication server, works
> > great and all but we're trying to set up a backup RADIUS server as well.
> >
> > That part isn't hard (setting it up) except I don't know what the
> > configuration settings are to make it authenticate off of a different
> > file, not just the system password file.
> >
> > Any ideas?  Thanks.
> >
> > Scott
> >
> >
> > -
> >  To unsubscribe to usr-tc, send an email to "[e-mail]"
> >  with "unsubscribe usr-tc" in the body of the message.
> >  For information on digests or retrieving files and old messages send
> >  "help" to the same address.  Do not use quotes in your message.
> >
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: "Michael J. Hartwick" <[e-mail]>
Subject: Re: (usr-tc) RADIUS question
Date: 28 Dec 2000 23:22:11 -0500 (EST)

On Thu, 28 Dec 2000 at 21:09 (-0600), Scott Kupferschmidt wrote:

SK> On that other server I want the RADIUS daemon to authenticate off of
SK> radius.passwd and not /etc/master.passwd -- How do I do this?

It depends on the RADIUS daemon you are using.  I modified the
original Livingston daemon to do this and it was a simply
modification.  I know that FreeRADIUS has that support, however,
FreeRADIUS isn't quite ready for full production use yet (still
alpha).  FreeRADIUS is based on Cistron.

Michael

Michael J. Hartwick, VE3SLQ                      [e-mail]
Hartwick Communications Consulting                      [phone]
Kincardine, ON, CA                             http://www.hartwick.com


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.


-------------------------------------------------------------------------------

From: Paul Farber <[e-mail]>
Subject: Re: (usr-tc) RADIUS question
Date: 29 Dec 2000 02:45:31 -0500 (EST)

No, if master.passwd is you system passwd file (and not a users file or
cbd file) then you will need to tell the raduis daemon what you want to
authenticate off of.... either a users file, the system password file or
some other.  You may want to look into mysql-ized raduis (ala freeraduis
or some other db enabled raduis.

Paul Farber
Farber Technology
[e-mail]
Ph  570-628-5303
Fax [phone]

On Thu, 28 Dec 2000, Scott Kupferschmidt wrote:

> Paul-
>
> Regarding what you said, that isn't what I asked. :-)
> Right now RADIUS is authenticating off of /etc/master.passwd in FreeBSD,
> and basically what we are doing is copying that file every 5 minutes to
> another server (radius.passwd is the name).
>
> On that other server I want the RADIUS daemon to authenticate off of
> radius.passwd and not /etc/master.passwd -- How do I do this?
>
> Unless I'm getting the wrong idea, and you're saying I have to put in
> "System = /etc/raddb/radius.passwd" ???
>
> Scott
>
>
> On Thu, 28 Dec 2000, Paul Farber wrote:
>
> > It's under AUTH-TYPE
> >
> > System = system files
> > 'password' = put the password in quotes, plain text
> > others you may have compiled in (cdb, SQL)
> >
> > Paul Farber
> > Farber Technology
> > [e-mail]
> > Ph  570-628-5303
> > Fax [phone]
> >
> > On Thu, 28 Dec 2000, Scott Kupferschmidt wrote:
> >
> > > Hey guys.  I have a question regarding RADIUS servers in general.  Right
> > > now we're using Cistron RADIUS on our main authentication server, works
> > > great and all but we're trying to set up a backup RADIUS server as well.
> > >
> > > That part isn't hard (setting it up) except I don't know what the
> > > configuration settings are to make it authenticate off of a different
> > > file, not just the system password file.
> > >
> > > Any ideas?  Thanks.
> > >
> > > Scott
> > >
> > >
> > > -
> > >  To unsubscribe to usr-tc, send an email to "[e-mail]"
> > >  with "unsubscribe usr-tc" in the body of the message.
> > >  For information on digests or retrieving files and old messages send
> > >  "help" to the same address.  Do not use quotes in your message.
> > >
> >
> >
> > -
> >  To unsubscribe to usr-tc, send an email to "[e-mail]"
> >  with "unsubscribe usr-tc" in the body of the message.
> >  For information on digests or retrieving files and old messages send
> >  "help" to the same address.  Do not use quotes in your message.
> >
>
>
> -
>  To unsubscribe to usr-tc, send an email to "[e-mail]"
>  with "unsubscribe usr-tc" in the body of the message.
>  For information on digests or retrieving files and old messages send
>  "help" to the same address.  Do not use quotes in your message.
>


-
 To unsubscribe to usr-tc, send an email to "[e-mail]"
 with "unsubscribe usr-tc" in the body of the message.
 For information on digests or retrieving files and old messages send
 "help" to the same address.  Do not use quotes in your message.