home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Internet Standards
/
CD2.mdf
/
ccitt
/
1992
/
q
/
q710.asc
< prev
next >
Wrap
Text File
|
1991-12-31
|
15KB
|
285 lines
All drawings appearing in this Fascicle have been done in Autocad.
Recommendation Q.710
SIMPLIFIED MTP VERSION FOR SMALL SYSTEMS
1 Field of application
1.1 This Recommendation is applicable for systems using a simplified MTP
version to interface to the public network(s).
1.2 The MTP functions specified in S 3 of this Recommendation may be applied
in general for small systems, e.g., PABX's, remote concentrators, etc.,
interfacing with the message transfer part described in Recommendations Q.702,
Q.703, Q.704 and Q.707.
1.3 The Recommendation applies only for digital access arrangements.
1.3.1 In case one channel carries signalling information for more than one
multiplex system, at least one additional channel should be pre-assigned as a
stand-by signalling link in a multiplex system other than that which contains the
active channel. This allows the changeover and changeback procedures specified in
SS 3.4.4 and 3.4.5 to be performed.
1.3.2 The stand-by channel(s) should not be used as B-channel(s).
1.4 Only the associated mode of signalling is applicable.
1.5 A variety of information types may be supported by the signalling system,
e.g., relating to circuit switched call control and packet communication.
2 Functional content
The functional requirements are as follows:
2.1 The network call control functions are as specified in Recommendation
Q.930 (I.451).
Note - Different network layer protocols (circuit switching and packet
switching) may be supported by using the protocol discriminator included in
Recommendation Q.930. As an alternative, different network layer entities may
access the interface functions directly. In that case, the interface functions
will use separate service indicator codes to discriminate the applicable network
layer entity. This will be similar to the use of SAPI specified in Recommendation
Q.920. Which principle to be applied is determined by the Administration/RPOA.
2.2 The minimum set of Message Transfer Part functions are specified in
Recommendations Q.702, Q.703, Q.704 and Q.707, with the qualifications specified
in S 3 of this Recommendation.
2.3 The additional interface functions required for the proper operation of
the D-channel call control functions in combination with the message transfer
part functions, are specified in S 4 of this Recommendation (see Figure 1/Q.710).
Figure 1/Q.710 - CCITT 72960
3 Message Transfer Part (MTP) functions
3.1 General
The MTP functions as specified in Recommendations Q.702, Q.703, Q.704 and
Q.707 are applicable. However, the following exceptions and modifications to
those Recommendations may be applied for the PABX system, see SS 3.2-3.4.
In order to prevent fraudulent use of the signalling network, it has to be
ensured that no signalling messages generated by a PABX can be routed further
than the public exchange to which the PABX has access. The manner in which this
is made may be dependent on national circumstances and system implementations. An
example of how such a function could be implemented is given in S 3.5.
3.2 Level 1 (Recommendation Q.702)
Only digital signalling data links are relevant. Recommendation Q.702, S
6, is not applicable.
3.3 Level 2 (Recommendation Q.703)
3.3.1 Initial alignment procedure (Recommendation Q.703, S 7)
In the initial alignment procedure specified in Recommendation Q.703, S 7,
only the emergency proving is applicable. Thus, in states "aligned" and "proving"
of the initial alignment procedure status indication "N" is not sent.
3.3.2 Processor outage (Recommendation Q.703, S 8)
The processor outage function specified in Recommendation Q.703, S 8, is
not applicable.
When the level 2 function receives an indication that a processor outage
situation exists at the remote and (through the reception of status signal units
indicating processor outage), it transmits status signal units indicating "out of
service".
3.3.3 Flow control (Recommendation Q.703, S 9)
CFascicle VI.7 - Rec. Q.710 PAGE1
The sending of the link status indication "B" from the PABX is not
applicable.
When the level 2 function of the PABX receives the link status indication
"B", no action is taken by the PABX.
3.4 Level 3 (Recommendation Q.704)
3.4.1 Routing label (Recommendation Q.704, S 2.2)
The signalling link selection (SLS) field defined in S 2.2.4 is always
coded 0000.
3.4.2 Message routing function (Recommendation Q.704, S 2.3)
The load sharing function between link sets and within a link set defined
in S 2.3.2 is not applicable.
3.4.3 Message discrimination (Recommendation Q.704, S 2.4)
The discrimination function defined in S 2.4.1 is not applicable.
3.4.4 Changeover (Recommendation Q.704, S 5)
Changeover between link sets is not applicable.
Initiation of changeover at the reception of a changeover order from the
remote end of a link is not applicable (c.f. Recommendation Q.704, S 3.2.2).
The buffer updating procedure defined in S 5.4 is not applicable.
At reception of a changeover order (or emergency changeover order) an
emergency changeover acknowledgement is sent in response.
The message retrieval procedure defined in S 5.5 is not applicable.
Diversion of traffic is performed at expiry of a time-out T1 (c.f.
Recommendation Q.704, S 16.8) is started when the changeover is initiated.
3.4.5 Changeback (Recommendation Q.704, S 6)
Changeback between link sets is not applicable.
The sequence control procedure defined in S 6.3 is not applicable. At
reception of a changeback declaration, a changeback acknowledgement is sent in
response.
For the purpose of ensuring message sequence integrity, the time
controlled diversion procedure specified in S 6.4 is used.
3.4.6 Forced rerouting (Recommendation Q.704, S 7)
Forced rerouting is not applicable.
3.4.7 Controlled rerouting (Recommendation Q.704, S 8)
Controlled rerouting is not applicable.
3.4.8 Signalling point restart (Recommendation Q.704, S 9)
Signalling point restart is not applicable.
3.4.9 Management inhibiting (Recommendation Q.704, S 10)
Management inhibiting is not applicable.
3.4.10 Signalling traffic flow control (Recommendation Q.704, S 11)
Signalling route set congestion (Recommendation Q.704, S 11.2.3) is not
applicable.
MTP User flow control (Recommendation Q.704, S 11.2.7) is not applicable.
3.4.11 Signalling link management (Recommendation Q.704, S 12.2)
Only basic link management procedures are applicable.
3.4.12 Link set activation (Recommendation Q.704, S 12.2.4)
Link set normal activation defined in S 12.2.4.1 is not applicable.
Link set emergency restart is used in all cases.
3.4.13 Transfer prohibited (Recommendation Q.704, S 13.2)
The transfer prohibited function is not applicable. At the reception of a
TFP message, no action should be taken.
3.4.14 Transfer allowed (Recommendation Q.704, S 13.3)
The transfer allowed function is not applicable. At the reception of a
TFA-message, no action should be taken.
3.4.15 Transfer restricted (Recommendation Q.704, S 13.4)
The transfer restricted function is not applicable for the PABX. At the
reception of the TFR message no action is taken by the PABX.
3.4.16 Signalling-route-set-test (Recommendation Q.704, S 13.5)
The signalling-route-set-test procedure is not applicable.
3.4.17 Transfer controlled (Recommendation Q.704, SS 13.7, 13.8)
The transfer controlled function is not applicable for the PABX. At the
reception of the TFC message, no action is taken by PABX.
3.4.18 Signalling route-set-congestion-test (Recommendation Q.704, S 13.9)
The signalling route-set-congestion-test function is not applicable for
the PABX.
At the reception of signalling-route-set-congestion-test message no action
PAGE6 Fascicle VI.7 - Rec. Q.710
is taken by the PABX.
3.4.19 Signalling link test (Recommendation Q.707, S 2.2)
The ability to respond to a signalling link test message with a signalling
link test acknowledge message must always be provided by the PABX.
3.5 Example of "Screening Function"
Note - This paragraph is provided for illustration purposes only.
At an exchange (which has the capability of acting as an STP) each message
received on a PABX access link is passed through a "screening function" that
checks that the DPC of the message is the same as the SP code of the exchange. If
that is the case, the message is sent to the normal MTP message handling
functions. Otherwise, the message is discarded.
4 Interface functions
4.1 General
The task of the interface functions is to provide the layer-to-layer
interfaces according to what is specified in Recommendations Q.920, Q.930 on the
one hand and in Recommendation Q.704 on the other, see the Figure 2/Q.710. This
will include some conversion functions which are specified in S 4.4.
Figure 2/Q.710 - CCITT 72970
4.2 Interactions with the network layer entity (Q.930)
The layer-to-layer interactions between the network layer and the data
link layer of the D-channel protocol are specified in Recommendation Q.920, S 4.
The interactions are specified in the form of primitives. The primitive
applicable for the primary rate interface structure are:
DL-DATA-REQUEST/INDICATION
The DL-DATA-REQUEST primitive is used to request that a network layer
message unit be sent. The DL-DATA-INDICATION indicates the arrival of a message
unit.
4.3 Interactions with the message transfer part
The layer-to-layer interactions between the MTP and the User Parts of
Signalling System No. 7 are specified in Recommendations Q.701 and Q.704, Figures
23/Q.704 and 27/Q.704.
The following primitives are used:
a) MTP-TRANSFER (see Recommendation Q.701, S 8.1),
b) MTP-PAUSE (see Recommendation Q.701, S 8.2),
c) MTP-RESUME (see Recommendation Q.701, S 8.3).
4.4 Conversion functions
The Table 1/Q.710 shows the association between the D-channel primitives
and the Signalling System No. 7 interactions.
TABLE 1/Q.710
D-channel SS No. 7
Information DL-DATA MTP-TRANSFER
transfer
Flow control - MTP-PAUSE (STOP)
- MTP-RESUME (START)
4.4.1 Information transfer
When receiving a DL-DATA-REQUEST primitive from the network layer entity,
the interface entity generates a MTP-TRANSFER Request primitive which contains:
- The message unit associated with the primitive.
- A label consisting of DPC, OPC and SLS. The label is generated by the
interface entity on the basis of information regarding the destination
of the message. The SLS is coded 0000.
Note - In some implementations where the label is not used for routing
purposes, the entire label may be coded "all zeros".
- A service information octet (SIO) is generated by the interface entity
in accordance with a predetermined rule and, as a national option, on
the basis of priority information associated with the primitive. The NI
is coded 10 or 11. The SI code is determined by the Administration or
RPOA.
Note - In the case when the interface functions provide direct access
to more than one network layer entity, the SI code will depend on the
network layer entity to which the message is associated.
When receiving a MTP-TRANSFER Indication from the MTP, the interface
entity sends a DL-DATA-INDICATION primitive to the network layer entity.
4.4.2 Flow control
CFascicle VI.7 - Rec. Q.710 PAGE1
When receiving a MTP-PAUSE indication from the MTP, the interface entity
will generate a DL-PAUSE-INDICATION primitive to the network layer entity.
When receiving a MTP-RESUME indication from the MTP, the interface entity
will generate a DL-RESUME-INDICATION primitive to the network layer entity.
PAGE6 Fascicle VI.7 - Rec. Q.710