Internet Standards/CD2.mdf/ccitt/1992/i/i432.asc

Text File | 1993-06-28 | 25KB | 977 lines

4.2.1.3.3    Allocation of OAM functions in information field
4.2.2.3    Interface structure at 622 080 Mbit/s
4.2.2.4.3    Transmission performance monitoring
_______________









INTERNATIONAL  TELECOMMUNICATION  UNION





CCITT    I.432

THE  INTERNATIONAL

TELEGRAPH  AND  TELEPHONE

CONSULTATIVE  COMMITTEE









INTEGRATED  SERVICES  DIGITAL

NETWORK  (ISDN)

OVERALL  NETWORK  ASPECTS

AND  FUNCTIONS,

ISDN  USER-NETWORK  INTERFACES





B-ISDN  USER-NETWORK  INTERFACE  û

PHYSICAL  LAYER  SPECIFICATION









Recommendation  I.432











Geneva, 1991











































































Printed in Switzerland













FOREWORD



    The CCITT (the International Telegraph and Telephone Consultative Committee) is a permanent
organ of the International Telecommunication Union (ITU). CCITT is responsible for studying technical,
operating and tariff questions and issuing Recommendations on them with a view to standardizing tele-
communications on a worldwide basis.

    The Plenary Assembly of CCITT which meets every four years, establishes the topics for
study and approves Recommendations prepared by its Study Groups. The approval of Recommenda-
tions by the members of CCITT between Plenary Assemblies is covered by the procedure laid down in
CCITT Resolution No. 2 (Melbourne, 1988).

    Recommendation I.432 was prepared by Study Group XVIII and was approved under the Resolu-
tion No. 2 procedure on the 5th of April 1991.





___________________









CCITT  NOTES



1)    In this Recommendation, the expression "Administration" is used for conciseness to indicate both a
telecommunication Administration and a recognized private operating agency.

2)    A list of abbreviations used in this Recommendation can be found in Annex C.

















aITU1991

All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from the ITU.







    Preamble to B-ISDN Recommendations

    In 1990, CCITT SG XVIII approved a first set of Recommendations on B-ISDN. These are:

I.113 û Vocabulary of terms for broadband aspects of ISDN

I.121 û Broadband aspects of ISDN

I.150 û B-ISDN asynchronous transfer mode functional characteristics

I.211 û B-ISDN service aspects

I.311 û B-ISDN general network aspects

I.321 û B-ISDN Protocol Reference Model and its application

I.327 û B-ISDN functional architecture

I.361 û B-ISDN ATM Layer specification

I.362 û B-ISDN ATM Adaptation Layer (AAL) functional description

I.363 û B-ISDN ATM Adaptation Layer (AAL) specification

I.413 û B-ISDN user-network interface

I.432 û B-ISDN user-network interface û Physical Layer specification

I.610 û Operation and maintenance principles of B-ISDN access

    These Recommendations address general B-ISDN aspects as well as specific service- and
network-oriented issues, the fundamental characteristics of the asynchronous transfer mode
(ATM), a first set of relevant ATM oriented parameters and their application at the user-network
interface as well as impact on operation and maintenance of the B-ISDN access. They are an inte-
gral part of the well established I-Series Recommendations. The set of Recommendations are intended
to serve as a consolidated basis for ongoing work relative to B-ISDN both within CCITT and in
other organizations. They may also be used as a first basis towards the development of network
elements.

    CCITT will continue to further develop and complete these Recommendations in areas where
there are unresolved issues and develop additional Recommendations on B-ISDN in the I-Series and
other series in the future.







PAGE BLANCHE









Recommendation I.432

Recommendation I.432



B-ISDN  USER-NETWORK  INTERFACE  û  PHYSICAL  LAYER  SPECIFICATION





1    Introduction

    This Recommendation defines a limited set of Physical Layer interface structures to be applied
to the SB and TB reference points of the reference configurations of the B-ISDN user-network inter-
face (UNI). It addresses separately the physical media and the transmission system structure
that may be used at these interfaces and addresses also the implementation of the UNI related OAM
functions.

    The selection of the physical medium for the interfaces at the SB and TB reference points
should take into account that optical fibre is agreed as the preferred medium to be used to cable
customer equipment. However, in order to accommodate existing cabling of customer equipment, other
transmission media (e.g. coaxial cables) should not be precluded. Also, implementations should
allow terminal interchangeability.

    This Recommendation reflects in its structure and content the desire to take care of such
early configurations and introduces a degree of freedom when choosing a physical medium at the
Physical Layer.

    Maximum commonality between functions of the Physical Layer described here at the UNI
and corresponding functions to be defined in the future at the NNI (network-node interface) is aimed
at.





2    Physical medium characteristics of the UNI at 155 520 Mbit/s



2.1    Characteristics of the interface at the TB reference point

2.1.1    Bit rate and interface symmetry

    The bit rate of the interface is 155 520 Mbit/s. The interface is symmetric, i.e. it has the same bit
rate in both transmission directions.

2.1.2    Physical characteristics

    Both optical and electrical interfaces are recommended. The implementation selected depends on
the distance to be covered and user requirements arising from the details of the installation.

2.1.2.1    Electrical interface

2.1.2.1.1    Interface range

    The maximum range of the interface is for further study. The connecting media between the trans-
mitter and receiver must cover a span from 0 to 100 metres and possibly up to 200 metres.

2.1.2.1.2    Transmission medium

    Two coaxial cables, one for each direction, are recommended. The wiring configuration is point-
to-point.

2.1.2.1.3    Electrical parameters

    The parameters for the 155 520 Mbit/s electrical interface in Recommendation G.703 should be
used as appropriate.

2.1.2.1.4    Connectors

    For further study.

2.1.2.2    Optical interface

2.1.2.2.1    Interface range

    The range of the interface is for further study. The connecting media between the transmitter and
receiver must cover a span from 0 to 800 metres and possibly up to 2000 metres.

2.1.2.2.2    Transmission medium

    The optical media (e.g. single mode fibre, multimode fibre, single fibre, dual fibre, etc.) are for
further study.

2.1.2.2.3    Optical parameters

    The optical parameters are for further study 1) .

2.1.2.2.4    Connectors

    For further study.



2.2    Characteristics of the interface at the SB reference point

    For further study.





3    Physical medium characteristics of the UNI at 622 080 Mbit/s

3.1    Characteristics of the interface at the TB reference point

3.1.1    Bit rate and interface symmetry

    The bit rate of the interface in at least one direction is 622 080 Mbit/s. The symmetry of the
interface is for further study. The following possible interfaces have been identified:

a)    an asymmetrical interface with 622 080 Mbit/s in one direction and 155 520 Mbit/s in the other
direction,

b)    a symmetrical interface with 622 080 Mbit/s in both directions.

    Note û Other solutions are for further study.

    If option a) is chosen, then the 155 520 Mbit/s component should comply with the character-
istics of _ 2.

3.1.2    Physical characteristics

3.1.2.1    Electrical interface

    The feasibility and range of application of an electrical interface is for further study.

3.1.2.2    Optical interface

    The parameters of _ 2.1.2.2 should be used as appropriate.



3.2    Characteristics of the interface at the SB reference point

    For further study.





4    Functions provided by the transmission convergence sublayer



4.1    Transfer capability

4.1.1    Interface at 155 520 Mbit/s

    At the physical level at the interface at the TB reference point the bit rate is 155 520 Mbit/s.
The bit rate available for user information cells, signalling cells and ATM and higher layers
OAM information cells, excluding Physical Layer related OAM information, transported in bytes
or cells, is 149 760 Mbit/s.

4.1.2    Interface at 622 080 Mbit/s

    At the physical level at the interface at the TB reference point, the bit rate is 622 080Mbit/s in
at least one direction (see _ 3.1). The bit rate available for user information cells, signalling
cells, and ATM and higher layer OAM information cells, excluding Physical Layer related OAM
information, transported in bytes or cells, is for further study.



4.2    Transmission frame adaptation

4.2.1    Physical Layer for the cell-based interface

4.2.1.1    Timing

    At the customer side of the interface at the TB reference point, the cell-based Physical Layer
may derive its timing from the signal received across the interface or provide it locally by the
clock of the customer equipment.

    The tolerance value of the bit rate is for further study.

4.2.1.2    Interface structure

    The interface structure consists of a continuous stream of cells. Each cell contains 53
octets.

4.2.1.3    OAM implementation

4.2.1.3.1    Transmission overhead allocation

    Physical Layer OAM cells are used for the conveyance of the Physical Layer OAM infor-
mation. How often OAM cells are inserted should be determined by OAM requirements.

4.2.1.3.2    OAM cell identification

    The Physical Layer OAM cell must have a unique header so that it can be properly identified
by the Physical Layer at the receiver. The pattern to be used is shown in Table 1/I.432 (see Note 1).

    The possible need to identify other header values among those reserved for the use of the
Physical Layer (see Recommendation I.361, _ 2.2.1) to accommodate future identified OAM flows is
for further study.









    Overhead allocation for the OAM functions (listed in Table 2/I.610) via the physical OAM
cell is for further study.

4.2.1.3.4    Maintenance signals

    Two maintenance signals are defined:

û    alarm indication signal (AIS),

û    far end receive failure (FERF).

    The use, generation and detection of AIS and FERF is for further study.

    Other maintenance signals are for further study.

4.2.1.3.5    Transmission performance monitoring

    Transmission performance monitoring across the UNI is performed to detect and report trans-
mission errors.

    An error code calculated over all cells between two successive Physical Layer OAM
cells is inserted in the information field of the relevant OAM cell. The encoding is for further
study.

4.2.1.3.6    Control communication

    For further study.

4.2.1.3.7    OAM procedures

    For further study.

4.2.2    Physical Layer for the SDH-based interface

4.2.2.1    Timing

    In normal operation, timing for the transmitter is locked to the timing received across the inter-
face. The exact tolerance under fault conditions is for further study.

4.2.2.2    Interface structure at 155 520 Mbit/s

    The bit stream of the interface has an external frame based on the synchronous digital hierar-
chy (SDH) as described in Recommendations G.707, G.708, and G.709. Specifically, the frame is given in
Recommendation G.709, and illustrated in Figure 1/I.432.

    The ATM cell stream is first mapped into the C-4 and then packed in the VC-4 container
along with the

VC-4 path overhead (see Figure 1/I.432). The ATM cell boundaries are aligned with the STM-1 octet
boundaries. Since the C-4 capacity (2340 octets) is not an integer multiple of the cell length (53
octets), a cell may cross a C-4 boundary.





FIGURE  1/I.432  =  12 cm









    The AU-4 pointer (bytes H1 and H2 in the SOH) is used for finding the first byte of the VC-4.
Path overhead (POH) bytes J1, B3, C2, G1 and H4 are utilised. Use of the remaining POH bytes is for
further study.

    The H4 pointer will be set at the sending side to indicate the next occurrence of a cell bound-
ary. The H4 pointer provides a cell boundary indication which may optionally be used to supple-
ment the mandatory HEC cell delineation mechanism (see _ 4.5).

    The H4 octet indicates the offset in octets from itself to the first cell boundary following
the H4 octet in the C-4 payload. The permissible range of values of H4 is 0 to 52. The bit allocation
for the H4 octet is given in Figure2/I.432









    This section is for further study.

4.2.2.4    OAM implementation

4.2.2.4.1    Transmission overhead allocation

    Transmission overhead allocation for the SDH Physical Layer functions (listed in Table 1/
I.610) is given in Table 2/I.432. Use of these overheads (e.g. for frame alignment, AU pointer genera-
tion/interpretation, bit interleaved parity (BIP) code calculation, etc.) shall be in accordance with
specifications in Recommendations G.708 and G.709 for the SDH network node interface.

4.2.2.4.2    Maintenance signals

    Two types of maintenance signals are defined for the Physical Layer to indicate the detection
and location of a transmission failure. These signals are:

û    alarm indication signal (AIS);

û    far end receive failure (FERF).

which are applicable at both the SDH section and path layers of the Physical Layer.

    AIS is used to alert the associated downstream termination point and connection point that
an upstream failure has been detected and alarmed.

    Far end receive failure (FERF) is used to alert the associated upstream termination point
that a failure has been detected downstream. Path FERF alerts the upstream path termination
point that a failure has occurred along the downstream path.

    Generation and detection of section and path AIS or FERF shall be in accordance with Rec-
ommendationG.709.









    Transmission performance monitoring across the UNI is performed to detect and report trans-
mission errors. Performance monitoring is provided for the section and for the path corresponding
respectively to maintenance flowsF2 and F3 in Figure 5/I.610.

    At the SDH section (F2 flow), monitoring of the incoming signal is performed using the BIP-24
inserted into the B2 field. Monitoring of the outgoing signal is performed using the far end block
error (FEBE). This error count, obtained from comparing the calculated BIP-24 and the B2 value of
the incoming signal at the far end, is inserted in the Z2 field bits 18 to 24 and send back and reports
to the near end section termination point about the error performance of its outgoing signal as
FEBE.

    Similar to the SDH section, at the SDH path (F3 flow), monitoring of the incoming signal is
performed using the BIP-8 of the B3 octet. Monitoring of the outgoing signal is performed using the
path FEBE of bits 1-4 of the G1octet.

    Regenerator section monitoring (F1 flow) across the UNI is optional. If required, the incoming
signal is monitored using the BIP-8 of the B1 octet. Capabilities in the SDH section overhead for
monitoring the outgoing signal are not provided.

4.2.2.4.4    Control communication

    Section layer communication channels and orderwires across the UNI are not required and are
not provided.

    Additional functions such as loopbacks (or their functional equivalent) or path layer
communication channels could be provided. Requirements for additional functions are for further
study.

    The use of octets K1 and K2 (bits 1-5) for automatic protection switching across the UNI is
for further study.

4.2.2.4.5    OAM procedures

    For further study.



4.3    Header error control

4.3.1    Header error control functions

    The header error control (HEC) covers the entire cell header. The code used for this function is
capable of either:

û    single-bit error correction, or

û    multiple-bit error detection.

    The detailed description of the HEC procedure is given in _ 4.3.2. Briefly, the transmitting
side computes the HEC field value. The receiver has two modes of operation as shown in Figure 3/
I.432. The default mode provides for single-bit error correction. Each cell header is examined and, if
an error is detected, one of two actions takes place. The action taken depends on the state of the
receiver. In "correction mode" only single-bit errors can be corrected and the receiver switches to
"detection mode". In "detection mode", all cells with detected header errors are discarded. When a
header is examined and found not to be in error, the receiver switches to "correction mode".





FIGURE  3/I.432  =   8 cm









    The flow chart in Figure 4/I.432 shows the consequence of errors in the ATM cell header.
The error protection function provided by HEC provides both recovery from single-bit header
errors, and a low probability of the delivery of cells with errored headers under bursty error
conditions. The error characteristics of fibre-based transmission systems appears to be a mix of
single-bit errors and relatively large burst errors. For some transmission systems the error
correction capability might not be invoked.





FIGURE  4/I.432  =  21  cm







    Annex A gives information on how random bit errors impact the probability of occurrence of
discarded cells and valid cells with errored headers.

4.3.2    Header error control (HEC) sequence generation

    The transmitter calculates the HEC value across the entire ATM cell header and inserts the
result in the appropriate header field.

    The notation used to describe the header error control is based on the property of cyclic
codes. (For example a code vector such as 1000000100001 can be represented by a polynomial P(x) =
x12 + x5 + 1.) The elements of an

n-element code word are thus the coefficients of a polynomial of order n-1. In this application,
these coefficients can have the value 0 or 1 and the polynomial operations are performed using
modulo 2 operations. The polynomial representing the content of a header excluding the HEC field is
generated using the first bit of a header as the coefficient of the highest order term.

    The HEC field shall be an 8-bit sequence. It shall be the remainder of the division (modulo 2)
by the generator polynomial x8 + x2 + x + 1 of the product x8 multiplied by the content of the header
excluding the HEC field.

    At the transmitter, the initial content of the register of the device computing the remainder
of the division is preset to all 0s and is then modified by division of the header excluding the HEC
field by the generator polynomial (as described above); the resulting remainder is transmitted as
the 8-bit HEC.

    To significantly improve the cell delineation performance in the case of bit-slips the fol-
lowing is recommended:

û    the check bits calculated by the use of the check polynomial are added (modulo 2) to an 8-bit
pattern before being inserted in the last octet of the header;

û    the recommended pattern is "01010101" (the left bit is the most significant bit);

û    the receiver must subtract (equal to add modulo 2) the same pattern from the 8 HEC bits
before calculating the syndrome of the header.

    This operation in no way affects the error detection/correction capabilities of the HEC.

    As an example if the first 4 octets of the header were all zeros the transmitted header
would be "00000000 00000000 00000000 00000000 01010101". The starting value for the polynomial
check is 0 . . 00 (binary).



4.4    Idle cells

    Idle cells cause no action at a receiving node except for cell delineation. They are inserted and
discarded for cell rate decoupling.

    Idle cells are identified by the standardized pattern for the cell header 2) shown in Table 3/
I.432.







    The content of the information field is for further study.



4.5    Cell delineation and scrambling

4.5.1    Cell delineation and scrambling objectives

    Cell delineation is the process which allows identification of the cell boundaries.

    The ATM cell header contains a header error control (HEC) field which is used to achieve
cell delineation.

    The ATM signal is required to be self-supporting in the sense that it has to be transpar-
ently transported on every network interface without any constraints from the transmission sys-
tems used.

    Scrambling will be used to improve the security and robustness of the HEC cell delineation
mechanism as described in _ 4.5.1.1. In addition it helps randomizing the data in the information field
for possible improvement of the transmission performance.

    Any scrambler specification must not alter the ATM header structure (as described in
Recommen-dationI.361), header error control (as described in _ 4.3), and cell delineation algorithm
(as described in _ 4.5.1.1).

4.5.1.1    Cell delineation algorithm

    The recommended cell delineation method is performed by using the correlation between the
header bits to be protected (32 bits) and the relevant control bits (8 bits) introduced in the header
by the HEC (header error control) using a shortened cyclic code with generating polynomial x8 + x2 +
x + 1.

    Figure 5/I.432 shows the state diagram of the HEC cell delineation method.





FIGURE  5/I.432  =   12 cm









    The details of the state diagram are described below:

1)    In the HUNT state, the delineation process is performed by checking bit by bit whether the
HEC coding law is respected (i.e.syndrome equals zero) for the assumed header field. Once such an
agreement is found, it is assumed that one header has been found, and the method enters the PRE-
SYNCH state. When octet boundaries are available within the receiving Physical Layer prior to cell delin-
eation, the cell delineation process may be performed octet by octet.

2)    The process repeats until the encoding law has been confirmed DELTA times consecutively.

3)    In the SYNCH state the cell delineation will be assumed to be lost if the HEC coding law is
recognized incorrectly ALPHA times consecutively.

    The parameters ALPHA and DELTA have to be chosen to make the cell delineation process
as robust and secure as possible and able to satisfy the performance specified in _ 4.5.2.

    Robustness against false misalignments due to bit errors depends on ALPHA.

    Robustness against false delineation in the resynchronization process depends on the
value of DELTA.

    Values of ALPHA = 7 and DELTA = 6 are suggested.

4.5.2     Cell delineation performance

    This section is for further study. Figures B-1/I.432 and B-2/I.432 give provisional information
on the performance of the cell delineation algorithm described in _ 4.5.1.1 in the presence of random
bit errors, for various values of ALPHA and DELTA.

4.5.3    Scrambler operation

    The following polynomial has been identified for the SDH-based Physical Layer.

    Self synchronizing scrambler x43 + 1

    This self synchronizing scrambler polynomial has been selected to minimize the error mul-
tiplication (two) introduced by the self synchronizing scrambler.

    The operation of this scrambler in relation to the HEC cell delineation state diagram is as
follows:

û    the scrambler randomizes the bits of the information field only;

û    during the five octet header the scrambler operation is suspended and the scrambler state
retained;

û    in the HUNT state the descrambler is disabled;

û    in the PRESYNCH and SYNC states the descrambler is enabled for a number of bits equal to
the length of the information field, and again disabled for the following assumed header.







ANNEX  A

(to Recommendation I.432)

Impact of random bit errors on HEC performance





FIGURE  A-1/I.432  =   16 cm





















ANNEX  B

(to Recommendation I.432)

Impact of random bit errors on cell delineation performance





FIGURE  B-1/I.432  =  14  cm



















FIGURE  B-2/I.432  =   13 cm















ANNEX  C

(to Recommendation I.432)

Alphabetical list of abbreviations used in this Recommendation



AIS        Alarm indication signal

BIP        Bit interleaved parity

FEBE        Far end block error

FERF        Far end receive failure

HEC        Header error control

POH        Path overhead

SDH        Synchronous digital hierarchy

UNI        User network interface