Internet Standards/CD2.mdf/ccitt/1992/i/i150.asc

Text File | 1993-06-28 | 21KB | 733 lines

_______________









INTERNATIONAL  TELECOMMUNICATION  UNION





CCITT    I.150

THE  INTERNATIONAL

TELEGRAPH  AND  TELEPHONE

CONSULTATIVE  COMMITTEE











INTEGRATED  SERVICES  DIGITAL

NETWORK  (ISDN)

GENERAL  STRUCTURE  AND  SERVICE

CAPABILITIES





B-ISDN  ASYNCHRONOUS  TRANSFER  MODE

FUNCTIONAL  CHARACTERISTICS











Recommendation  I.150











Geneva, 1991











































































Printed in Switzerland















FOREWORD



    The CCITT (the International Telegraph and Telephone Consultative Committee) is a permanent organ of the Interna-
tional Telecommunication Union (ITU). CCITT is responsible for studying technical, operating and tariff questions and issuing
Recommendations on them with a view to standardizing telecommunications on a worldwide basis.

    The Plenary Assembly of CCITT which meets every four years, establishes the topics for study and approves
Recommendations prepared by its Study Groups. The approval of Recommendations by the members of CCITT
between Plenary Assemblies is covered by the procedure laid down in CCITT Resolution No. 2 (Melbourne, 1988).

    Recommendation I.150 was prepared by Study Group XVIII and was approved under the Resolution No.
2 procedure on the 5 of April 1991.





___________________









CCITT  NOTES



1)    In this Recommendation, the expression "Administration" is used for conciseness to indicate both a telecommunica-
tion Administration and a recognized private operating agency.

2)    A list of abbreviations used in this Recommendation can be found in Annex A.

















aITU1991

All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the ITU.







    Preamble to B-ISDN Recommendations

    In 1990, CCITT SG XVIII approved a first set of Recommendations on B-ISDN. These are:

I.113 û Vocabulary of terms for broadband aspects of ISDN

I.121 û Broadband aspects of ISDN

I.150 û B-ISDN asynchronous transfer mode functional characteristics

I.211 û B-ISDN service aspects

I.311 û B-ISDN general network aspects

I.321 û B-ISDN Protocol Reference Model and its application

I.327 û B-ISDN functional architecture

I.361 û B-ISDN ATM Layer specification

I.362 û B-ISDN ATM Adaptation Layer (AAL) functional description

I.363 û B-ISDN ATM Adaptation Layer (AAL) specification

I.413 û B-ISDN user-network interface

I.432 û B-ISDN user-network interface û Physical Layer specification

I.610 û Operation and maintenance principles of B-ISDN access

    These Recommendations address general B-ISDN aspects as well as specific service- and network-ori-
ented issues, the fundamental characteristics of the asynchronous transfer mode (ATM), a first set of relevant
ATM oriented parameters and their application at the user-network interface as well as impact on operation
and maintenance of the B-ISDN access. They are an integral part of the well established I-Series Recommen-
dations. The set of Recommendations are intended to serve as a consolidated basis for ongoing work relative to
B-ISDN both within CCITT and in other organizations. They may also be used as a first basis towards the devel-
opment of network elements.

    CCITT will continue to further develop and complete these Recommendations in areas where there are
unresolved issues and develop additional Recommendations on B-ISDN in the I-Series and other series in the
future.







PAGE BLANCHE









Recommendation I.150

Recommendation I.150



B-ISDN  ASYNCHRONOUS  TRANSFER  MODE  FUNCTIONAL  CHARACTERISTICS





1    Introduction

    This Recommendation addresses specifically the functions of the ATM Layer. This Layer is common to all
services including signalling and OAM.





2    Basic principles of ATM

    ATM is the transfer mode solution for implementing a B-ISDN. It influences the standardization of digital
hierarchies, multiplexing structures, switching and interfaces for broadband signals.

    ATM is used in this Recommendation for addressing a specific packet-oriented transfer mode which
uses asynchronous time division multiplexing techniques. The multiplexed information flow is organized into
blocks of a fixed size called cells. A cell consists of an information field and a header. The primary role of the
header is to identify cells belonging to the same virtual channel within the asynchronous time division multi-
plex. Transfer capacity is assigned by negotiation and is based on the source requirements and the available
capacity. Cell sequence integrity on a virtual channel connection is preserved by the ATM Layer.

    ATM is a connection-oriented technique. Connection identifiers are assigned to each link of a connec-
tion when required and released when no longer needed. In general, signalling and user information are carried
on separate ATM Layer connections.

    ATM offers a flexible transfer capability common to all services, including connectionless services.
Additional functionalities on top of the ATM Layer (e.g. in the ATM Adaptation Layer (AAL)) are provided to
accommodate various services. The boundary between the ATM Layer and the AAL corresponds to the boundary
between functions supported by the contents of the cell header and functions supported by AAL-specific infor-
mation. The AAL-specific information is contained in the information field of the ATM cell.

    The information field is transported transparently by the ATM Layer. No processing, e.g. error control,
is performed on the information field at the ATM Layer.

    The header and information field each consists of a fixed integer number of octets. The header size (5
octets) and the information field size (48octets) remain constant at all reference points, including the User-
network interface (UNI) and the Network-node interface (NNI), where the ATM technique is applied.





3    ATM Layer



3.1    ATM Layer connections

3.1.1    Connection definition

    An ATM Layer connection consists of the concatenation of ATM Layer links in order to provide an end-to-
end transfer capability to access points.

3.1.2    Connection identifiers

3.1.2.1    Virtual path identifiers (VPIs) and virtual channel identifiers (VCIs)

    At a given interface, in a given direction, the different virtual path (VP) links multiplexed at the ATM
Layer into the same Physical Layer connection are distinguished by the VPI. The different virtual channel (VC)
links in a virtual path connection (VPC) are distinguished by the VCI as indicated in Figure 1/I.150.





FIGURE 1/I.150   =   cm









3.1.2.2    VPI-VCI relationships

    Two different VCs belonging to two different VPs at a given interface may have the same VCI value. There-
fore, a VC is only fully identified at an interface by both VPI and VCI values.

    A specific value of VCI has no end-to-end significance if the virtual channel connection (VCC) is
switched. VPIs may be changed wherever VP links are terminated (e.g. cross-connects, concentrators and
switches). VCIs may only be changed where VC links are terminated. As a consequence, VCI values are preserved
within a VPC.

3.1.2.3    Number of active connections at the UNI

    At the UNI, 24 bits are available in the VPI/VCI field for connection identification. The actual number of
routing bits in the VPI and VCI fields used for routing is negotiated between the user and the network, e.g. on
a subscription basis. This number is determined on the basis of the lower requirement of the user or the net-
work. The rules to determine the position of the routing bits used within the VPI/VCI field are given in _ 2.2.3
of Recommendation I.361.

3.1.3    Aspects of virtual channel connections (VCCs)

3.1.3.1    General characteristics of VCCs

    The definition of a VCC is given in Recommendation I.113. This section provides additional explanations to
facilitate the understanding of the following topics:

a)    Quality of service: a user of a VCC is provided with a Quality of Service specified by parameters such as
cell loss ratio and cell delay variation;

b)    Switched and (semi-) permanent VCCs: VCCs can be provided on a switched or (semi-) permanent basis;

c)    Cell sequence integrity: cell sequence integrity is preserved within a VCC;

d)    Traffic parameter negotiation and usage monitoring: traffic parameters shall be negotiated between a user
and a network for each VCC at VCC establishment and may be subsequently renegotiated. Input cells from the user to the
network will be monitored to ensure that the negotiated traffic parameters are not violated.

3.1.3.2    Establishment and release of a VCC

3.1.3.2.1    Establishment/release at the UNI

    VCCs may be established/released using one or more of the following four methods:

a)    without using signalling procedures, e.g. by subscription [(semi-)permanent connections];

b)    meta-signalling procedures (see Recommendation I.311), e.g. by using a meta-signalling VCC to estab-
lish/release a VCC used for signalling;

c)    user-to-network signalling procedures, e.g. using a signalling VCC to establish/release a VCC used for
end-to-end communications;

d)    user-to-user signalling procedures, e.g. using a signalling VCC to establish/release a VCC within a pre-
established VPC between two UNIs.

    The value assigned to a VCI at a UNI using the methods listed above could be assigned by one of the fol-
lowing:

a)    the network;

b)    the user;

c)    negotiation between the user and the network;

d)    standardization.

    The specific value assigned to a VCI at a UNI is, in general, independent of the service provided over that
VC. For terminal interchangeability and initialization it is desirable to use the same value for certain functions
on all UNIs. For example, the same VCI value for the meta-signalling VC will be used on all UNIs in order to
simplify initialization of the terminal equipment.

3.1.3.2.2    Establishment/release at the NNI

    ATM network elements (e.g. ATM switches, cross-connects and concentrators) process the ATM cell header
and may provide VCI and/or VPI translation. Thus, whenever a VCC is established/released across the ATM net-
work, VC links may need to be established/released at one or more NNIs. VC links are established/released
between ATM network elements using inter- and intra-network signalling procedures; other methods are also
possible.

3.1.3.3    Pre-assigned VCIs

    Pre-assigned VCI values are reserved for:

a)    unassigned cell identification;

b)    meta-signalling VC identification;

c)    general broadcast signalling VC identification;

d)    physical layer cell identification;

e)    other uses are for further study.

    Additional information concerning the use of these values in combination with VPI values can be found in
_3.1.4.3.

3.1.3.4    Signalling VCs

    Refer to Recommendation I.311.

3.1.3.5    OAM VCs

    Refer to Recommendation I.610.

3.1.4    Aspects of Virtual Path Connections (VPCs)

3.1.4.1    General characteristics of VPCs

    The definition of a VPC is given in Recommendation I.113. This section gives additional explanations con-
cerning VPCs to facilitate the understanding of the following topics:

a)    Quality of service

    A user of a VPC is provided with a quality of service specified by parameters such as cell loss ratio and
cell delay variation.

b)    Switched and (semi-) permanent VPCs

    VPCs can be established on a switched or (semi-) permanent basis.

c)    Cell sequence integrity

    Cell sequence integrity is preserved for each VCC within a VPC.

d)    Traffic parameters negotiation and usage monitoring

    Traffic parameters will be negotiated between a user and the network for each VPC at VPC establishment
and may be subsequently renegotiated. Input cells from the user to the network will be monitored to ensure that the
negotiated traffic parameters are not violated.

e)    VCI restrictions within a VPC

    One or more VCIs within a VPC may not be available to the user of the VPC. The number and values of
these VCIs are for further study.

3.1.4.2    Establishment and release of a VPC

    A VPC may be established/released between VPC endpoints by one of the following methods. These meth-
ods are for further study.

a)    Establishment/release without using signalling procedures. In this case the VPC is established/released on
a subscription basis.

b)    Establishment/release on demand:

    û    Customer controlled VPC establishment/release where VP configuration may be performed by the user
invoking signalling or network management procedures.

    û    Network controlled VPC establishment/release may be performed by network signalling procedures.

3.1.4.3    Pre-assigned VPIs

    Pre-assigned VPI values are used for:

a)    unassigned cell identification and physical layer cell identification;

    Note û For the unassigned cell identification and cells reserved for use by the physical layer, a pre-
assigned value of VPI/VCI combination is reserved.

b)    meta-signalling VC identification;

c)    general broadcast signalling VC identification;

d)    other uses are for further study.

3.1.5    Pre-assigned cell header values

    Cells reserved for the use of the physical layer have pre-assigned values reserved for the whole header;
these values are not to be used by the ATM layer.



3.2    Service characteristics

3.2.1    Services expected from the physical layer

    For further study.

3.2.2    Services provided to the higher layer

    For further study.



3.3    Management plane interactions

    For further study.



3.4    Functions of the ATM layer

3.4.1    Cell multiplexing and switching

    The basic ATM routing entity for switched services is the VC. It is handled in VC multiplexers/demultiplex-
ers and switches. VCs are aggregated in VPCs which are routed as such through VP multiplexers/demultiplexers
and VP switches (see Figure 2/I.150).





FIGURE 2/150   =   cm









3.4.2    Quality of service (QOS) provided by the ATM layer

3.4.2.1    QOS related to VCCs

    A user of a VCC is provided with one of a number of QOS classes supported by the network. Specific QOS
classes and the quality provided by each QOS class require further study. Requested QOS classes are indicated
to networks at call/connection establishment. The QOS class associated with a given connection within a call
will not change for the duration of the connection. Renegotiation of the QOS class may require the establish-
ment of a new connection.

3.4.2.2    QOS related to VPCs

    A user of a VPC is provided with one of a number of QOS classes supported by the network. Specific QOS
classes and the quality provided by each class require further study. Requested QOS classes are indicated to
networks at call/connection establishment. The QOS classes associated with a VPC will not change for the
duration of the VPC.

    It should be noted that a VPC will carry VC links of various QOS classes. The QOS of the VPC must meet
the most demanding QOS of the VC links carried.

3.4.2.3    QOS related to cell loss priority (CLP)

3.4.2.3.1    General

    Many variable bit rate (VBR) services will require a guarantee of some minimum capacity as well as a peak
capacity. In times of network congestion, the network will need to know which cells can be discarded without
violating the negotiated QOS parameters (for example, the guaranteed minimum capacity).

    Some VBR services will benefit if the user or service provider (e.g.layered coding video provider) can
select which cells have the higher loss sensitivity.

3.4.2.3.2    CLP indicator

    One bit in the cell header is used for explicit cell loss priority indication. This bit may be set by the user
or service provider to indicate lower priority cells. Cells with the CLP bit set are subject to discard depending
on network conditions. Cells with the CLP bit not set have higher priority as capacity for them has been allo-
cated within the network.

    The network will monitor the connection in accordance with mechanisms described in Recommen-
dationI.311 in order to protect the QOS of other users.

    The rate of higher priority cells will be determined at call establishment and may be subsequently
renegotiated. Cells arriving at the network in excess of this rate will be subject to network usage parameter
control. Cells arriving at the network in excess of other agreed parameters for the call will also be subject to
normal usage parameter control.

    Note û The cell loss priority mechanism would not normally be used for constant bit rate (CBR) ser-
vices, i.e. cells belonging to a CBR service would not normally have the CLP indicator set.

3.4.3    Payload type functions

    The payload type field is used to provide an indication of whether the cell payload (i.e. information field)
contains user information or network information. In user information cells the payload consists of user infor-
mation and service adaptation function information. In network information cells the payload does not form
part of the user's information transfer.

    When the payload type field does not indicate user information, further information concerning the
type of network control will be found in the information field of the cell.

    It is envisaged that network information cells would be generated within the network but might cross
the UNI. Use of network information cells by users is for further study.

    The use of the payload type field for additional functions related to usage parameter control is for
further study.

3.4.4    Generic flow control (GFC) at the UNI

    The GFC mechanism assists in the control of the flow of traffic from ATM connections of various QOS
classes (related to the ATM Layer). More specifically, the GFC mechanism is used to control traffic flow in order
to alleviate short-term overload conditions that may occur.

    In situations where flow control is unnecessary, the impact of the implementation of the GFC mecha-
nism on the terminal is for further study.

    The specification of the GFC mechanism is for further study. However, the mechanism is expected to
conform to the following:

a)    The flow control at the UNI is supported by the ATM cell header. The GFC field is used to provide this func-
tion.

b)    The GFC mechanism may assist the customer network in providing various QOS within the customer net-
work.

c)    The GFC mechanism should not perform flow control of traffic from the network. The use of GFC at SB and
TB is as follows:

i)    GFC at SB

    The GFC field is present at the interface at the SB reference point and the I* interface.

    The GFC mechanism should provide flow control of information generated locally by terminals within a cus-
tomer's premises. This traffic may occur in directions to and from the terminal across the interface at the SB reference
point and the I*interface. Operation of the GFC mechanism within the B-NT2 to control the traffic in the B-NT2 to termi-
nal direction is for further study. The specific mechanism at the interface at the SB reference point and I* interface is for
further study.

ii)    GFC at TB

    The GFC field is present at the interface at the TB reference point. It may be used to provide flow control
of information transfer in a direction from the B-TE to the network; however, this and the specific mechanism at TB is for
further study.

d)    The GFC mechanism resides in the ATM Layer and is independent of the Physical Layer.

e)    The GFC mechanism applies at B-UNIs and should support the configurations of _ 2.2 of Recommendation
I.413.

f)    The GFC mechanism must allow a terminal to achieve an assured capacity or bandwidth allocated by the
network to both CBR and VBR calls. In the case of VBR services, the GFC mechanism must be able to partition fairly and
efficiently the capacity above that guaranteed for all active connections.

g)    The GFC mechanism should not compromise terminal interchangeability.

ANNEX  A

(to Recommendation I.150)

Alphabetical list of abbreviations contained in this Recommendation



AAL    ATM Adaptation Layer

CBR    Constant bit rate

CLP    Cell loss priority

GFC    Generic flow control

NNI    Network-node interface

QOS    Quality of service

UNI    User-network interface

VBR    Variable bit rate

VC    Virtual channel

VCC    Virtual channel connection

VCI    Virtual channel identifier

VP    Virtual path

VPC    Virtual path connection

VPI    Virtual path identifier