home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Internet Standards
/
CD2.mdf
/
ccitt
/
1992
/
e
/
e713.asc
< prev
next >
Wrap
Text File
|
1991-12-30
|
11KB
|
285 lines
All drawings appearing in this Recommendation have been done in Autocad.
Recommendation E.713
CONTROL PLANE TRAFFIC MODELS
1 Control plane traffic
For the purposes of teletraffic engineering, the control plane traffic
load is assumed to be generated by call attempts on the network. These call
attempts are part of the call pattern described in Recommendation E.711.
This Recommendation considers traffic loads at the lower three layers of
the CCITT 7-layer reference models (Recommendation I.310 and I.320) described for
ISDN in Recommendation Q.931 and in Signalling Sytem No. 7.
The control plane traffic of an ISDN network includes all the control
signals sent through the ISDN network. The types of control signals are:
1) signals for user call attempts
a) to set up the connection paths in the user plane (reservation of
time slots for circuit switched connections or control for the
virtual calls of packet-switched connections),
b) to release the connection paths in the user plane,
c) if required, to order additional communication facilities or change
of service by the users during the time of user information
transfer,
d) possibly to send charging information during the time of user
information transfer.
2) User-to-user information messages1)
Because control plane traffic due to user-to-user messages is left for
further study, this Recommendation will consider only signals for user call
attempts.
The control plane traffic uses two types of channels in the network:
a) the 16 kbit/s or 64 kbit/s D-channels in the user access, and
b) the 64 kbit/s Signalling System No. 7 channels connecting two different
signalling points.
2 Signalling traffic
The end-to-end ISDN signalling traffic depends on the call pattern arrival
process defined in Recommendation E.711 and on the signalling protocol.
The basis for the estimation of the signalling traffic is the information
given in the Recommendations of the I- and Q-Series dealing with the number and
structure of the signals in the D- and Signalling System No. 7 channels for any
type of attempt. The total signalling traffic is composed of these signals. The
number of signals may be different for each different type of attempt.
3 Estimation of the signalling traffic for a single call attempt
In Figure 1/E.713 the network components supporting the control plane of
the ISDN reference connection of Figure 1/E.701 are considered. In each section,
a significant point is defined:
DA (D-channel, A user side): S/T interface at an A user side
DB (D-channel, B user side): S/T interface at a B user side
CA (S.S. No. 7 channels, A user side): outgoing side of the local
exchange LE(A).
CB (S.S. No. 7 channels, B user side): incoming side of the local
exchange LE(B).
Figure 1/E.713
The signal flow which is necessary to perform the control functions of a
particular call attempt may be represented by a signal flow diagram. It contains
all the signals passing the significant points in the control plane for the
considered attempt. Figure 2/E.713 shows the basic scheme of this signal flow
diagram. The arrows represent the layer 2 signals in the three connection phases:
call establishment, user information transfer, and call release.
An example of a signal flow diagram for a successful circuit switched call
attempt is given in Annex A.
The signal flow diagram is the basis for the estimation of the amount of
signalling traffic caused by the considered attempt using the reference
connection. The signalling traffic of a single attempt in a given section of the
control plane associated with a significant point can be described by two sets of
parameters:
1) the total number of signals passing the significant point in the three
1) The analysis of user-to-user messages in the control plane is left for further study.
Fascicle II.3 - Rec. E.713 PAGE1
call-connection phases in the A-to-B direction and in the B-to-A
direction, as in Figure 2/E.713;
2) the length of each signal type passing the significant point in the
A-to-B and the B-to-A direction.
Figure 2/E.713
4 Estimation of the total signalling traffic
The total number of signals in the control plane over a reference period2)
is determined by summing the number of signals caused by call attempts handled in
the associated user plane during the reference period. Therefore the estimation
of the number of signals is based on the estimation of the amount and types of
attempts in the user plane.
In order to estimate the amount of signals, it is necessary to accept a
traffic model for the traffic in the user plane assuming the total number of
attempts over the reference period and the breakdown of these attempts into the
different types of attempts, such as successful call attempts, unsuccessful call
attempts and calls to busy tone.
The total traffic load of a section caused by the signals is expressed by
the total amount of bits crossing its significant point.
In order to estimate the amount of this traffic load it is necessary to
multiply the length of each particular type of signals by the number of signals
of each type occuring during the reference period and summing over all types of
signals occuring during the reference period.
Since the number and length of the signals do not vary widely for most
types of attempts, initially this traffic model will be adequate by taking into
consideration only the most frequently experienced types of attempts.
2) The proper reference period to use for dimensioning is for further study.
PAGE4 Fascicle II.3 - Rec. E.713
The characteristic of the signalling traffic in a particular section of
the control plane will depend on such factors as:
a) the total traffic load caused by layer 2 and 3 signals for the
attempts.
b) the distribution of call attempts and release arrivals.
The impact on teletraffic engineering caused by a full characterization of
the arrival process is left for further study.
Using Figure 2/E.713, the signalling traffic load at a significant point
can be estimated.
If, over the reference period:
i is the call phase,
j is the signal type,
nij (u) is the average number of signals of type j in call phase i in
the A-to-B direction,
nij (d) is the average number of signals of type j in call phase i in
the B-to-A direction,
lj is the length of signal of type j,
T is the total number of signals types,
L(u) is the total load in the A-to-B direction,
L(d) is the total load in the B-to-A direction,
then:
eq L(u) = \i\su(i=1,3, ) \i\su(j=1,T, ) lj x nij (u)
eq L(d) = \i\su(i=1,3, )\i\su(j=1,T, ) lj x nij (d)
Each nij (u) and nij (d) must be estimated from the number of call attempts and
the call attributes in the user plane over the reference period. An example of
this procedure is given in Annex A.
Fascicle II.3 - Rec. E.713 PAGE1
ANNEX A
(to Recommendation E.713)
Example of procedure for estimating
the total signalling traffic in a D-channel
A.1 Signalling traffic for one call attempt
A call attempt of the following type is considered:
- effective call attempt,
- circuit switched connection,
- en-bloc sending of dialled information,
- call to an appointed terminal,
- no additional control signals during the information transfer phase,
- installation of data link in the D-channels required for establishment
and release of the connection,
- manual answering terminal.
The signal flow diagram for this type of call attempt is given in Figure
A-1/E.713 and Figure A-2/E.713. Three kinds of signals are indicated in Figure
A-1/E.713:
- layer 3 signals,
- layer 2 signals for the activation and deactivation of the data links,
- end-to-end signals via the S.S. No. 7 network.
Figure A-2/E.713 presents the breakdown of the D-channel signals into
layer 2 for the case of multiple terminals on the terminating side. The breakdown
of the S.S. No. 7 messages and the total length of signal in the considered call
attempt is for further study.
A.2 Signalling traffic for additional types of call attempts
For further study.
Figure A-1/E.713
Figure A-2/E.713
PAGE4 Fascicle II.3 - Rec. E.713