home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
DP Tool Club 17
/
CD_ASCQ_17_101194.iso
/
vrac
/
izmbeta6.zip
/
INSTALL.DOC
< prev
next >
Wrap
Text File
|
1994-09-13
|
13KB
|
279 lines
This text file is meant to help you install IceZmodem with your
particular terminal program or BBS. If you have any questions,
send mail to one of the addresses found in IZM.DOC.
PLEASE NOTE -- IF YOUR BBS/TERMINAL PROGRAM IS NOT LISTED HERE
""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""""
Attempt to set up IceZmodem using the same command lines as you have
set the DSZ protocol up with. Please keep in mind that the command
lines are NOT exactly the same. IceZmodem does not support any "-"
options that are placed after the SZ or RZ commands such as "-m" and
"-mrr", so DO NOT include these in your command line or the transfer
is guaranteed to not work properly! Also, instead of portx use the
adrirq option.
If you do get it set up, please e-mail me your BBS/terminal program
name and the exact steps to setting it up and I will include it in
this INSTALL.DOC, giving you proper credit. Thank You!
Setting up IceZmodem with Telemate
""""""""""""""""""""""""""""""""""
Hit Alt-O and then hit E for the external protocol menu. Hit the down
arrow until you reach an empty protocol name slot.
Type in IceZmodem for the name.
For key, use the letter I.
For upload batch, enter IZM-U
For download batch, enter IZM-D
Hit the down arrow twice,
For auto-download sequence, enter *^XB00 and hit ENTER.
Get out of the external protocol menu and hit P to enter the Protocol
menu. Make sure the Zmodem Auto-Download does not have an X next to it.
If it does, remove the X. Get out of the Protocol menu and hit G for
general options. To get the most out of IceZmodem, make sure that
Maximum DOS Shell and Swap to Disk both have X's next to them. Exit
that menu and select "Save Options". Now copy IZM.EXE and IZMSETUP.EXE
into your Telemate Directory.
Copy the files IZM-U.BAT and IZM-D.BAT into your Telemate Directory.
Be sure to edit the IZM-D.BAT to specify the proper download directory.
If you are using NONSTANDARD COM PORTS, remove the "port" option!
Setting up IceZmodem with Qmodem v4.x
"""""""""""""""""""""""""""""""""""""
Copy IceZmodem files into your Qmodem Directory.
Hit Alt-N or load QINSTALL.EXE. Hit P and press the down arrow till you
reach an empty protocol slot and hit enter.
For Select Character, type in I
For Protocol, type in IceZmodem
For Upload Batch, type in IZM-U
For Download Batch, type in IZM-D
For Filename Prompt, type in N
Get out of that menu and go to the Toggles option (still in the
Protocol menu). Ensure that Zmodem AutoStart is off. Go back up to the
menu bar and go to the Options menu. From that menu, select Runtime
Parms. Make sure that Optimum Shell and Disk Shell are turned on. Exit
Qinstall with the Save Changes option.
Copy the files IZM-U.BAT and IZM-D.BAT into your Qmodem Directory.
Edit the line in IZM-U.BAT to look like this:
IZM port %2 sz %4 %5 %6 %7 %8 %9
Be sure to edit the IZM-D.BAT to specify the proper download directory.
** If you are using NONSTANDARD COM PORTS, remove the "port" option **
Setting up IceZmodem with Telix
"""""""""""""""""""""""""""""""
Hit Alt-O and then P for Protocol Options. Hit A,B,C, or D to pick a
slot for IceZmodem - whichever is empty.
For key, type in I
For protocol name, type in IceZmodem
For upload filename, type in IZM-U
For download filename, type in IZM-D
For batch or script, select Batch File
Prompt for name on downloads, No.
If supported, Trigger should be *<UP ARROW>B00
To get the <UP ARROW> in the above Trigger, hit CTRL-X.
--- Do not type <UP ARROW> !! ---
Exit the Protocol Options menu and go into the Terminal Options menu.
Hit N to turn Zmodem Auto-Downloads off. Select Write Setup to Disk.
Copy IceZmodem files into your Telix Directory.
Copy the files IZM-U.BAT and IZM-D.BAT into your Telix Directory.
Be sure to edit the IZM-D.BAT to specify the proper download directory.
** If you are using NONSTANDARD COM PORTS, remove the "port" option **
Setting up IceZmodem with Terminate
"""""""""""""""""""""""""""""""""""
Copy IceZmodem files into your protocol directory (\TM\PROTOCOL)
Load Terminate, Hit ALT-O. Select Protocol Options, select External.
Pick an open protocol slot and enter the following information:
Protocol Name....: IceZmodem
Information......: Zmodem with Chat/DOS/Screen Saver/MOD Player,etc..
PATH + Filename..: IZM.EXE
Ask at downloads.: No
Change to U/L DIR: Yes
Change to D/L DIR: Yes
Batch............: Yes
Hotkey...........: I
Upload Parameters: !M port !P sz
Download Params..: !M port !P rz
Auto-Download....: Yes
Signature........: *<UP ARROW>B00
To get the <UP ARROW> in the above signature, hit CTRL-X.
--- Do not type <UP ARROW> !! ---
Hit Esc and be sure IceZmodem is active with a "■" next to it. If
not, hit the space bar. Go back to the Protocol Options menu.
Select Internal. Select Enable Protocols. Disable the Zmodem and
ZedZap protocols. Hit Esc twice, select External. Disable all
Zmodem protocols except for IceZmodem. Go back to the Protocol
Options menu and make sure IceZmodem is the default protocol.
Exit and select write setup to disk.
Setting up IceZmodem with {COMMO} 5.52 and Later Versions
Doc Written by Roger Pariseau (Roger.Pariseau@tomcat.com)
"""""""""""""""""""""""""""""""""""""""""""""""""""""""""
Hit Alt-M to enter the Macro Editor. Hit the down arrow until you
reach the "DOWNLOAD (receive) menu macro" line. Hit E to enter the
editor and Add "/IZM" to the "using" line. Make sure the right
brace (}) lines up with all the other menu entries. Hit the down
arrow until you reach the "UPLOAD (send) menu macro" line. Do
exactly the same as you did for the DOWNLOAD menu.
Cursor down until you reach the "Protocol macros used for
DOWNLOADING (receiving)" line. Insert (Alt-I) two lines after
(:txzm#r}.
Type in the following:
{:izm#r} {exec-d %protodir\%progdsz port %_por rz %pr_down}
{alarm %pr_alarm} {retu}
Cursor down until you reach the "Protocol macros used for UPLOADING
(sending)" line. Insert (Alt-I) two lines after {:txzm#s}. Type in
the following:
{:izm#s} {exec-d %protodir\%progdsz port %_por sz %pr_file}
{alarm %pr_alarm} {retu}
Hit Alt-F to save the file and ESC back to the terminal screen.
Hit Alt-G to enter the Setup File. Cursor down to the "Terminal and
Modem" section. Press "E" to enter the editor and change "{set
z_prog,XXXX}" to {set z_prog,IZM} and add "/IZM" to the description
line (DSZC/DSZE/GSZ/TXZM/IZM). Hit Alt-F to save the file and ESC
back to the terminal screen.
IF YOU ARE USING NONSTANDARDS COM PORTS, remove the "port %_por"
from both the DOWNLOAD and UPLOAD entries.
Exit {COMMO} and re-run the program to make these changes effective
for your next terminal session.
Setting up IceZmodem with a PCBoard BBS
"""""""""""""""""""""""""""""""""""""""
In PCBSETUP go to File Locations, Configuration Files and then
scroll down to Protocol Data File and hit F2. Scroll down to an
empty slot and enter the data below:
Use = I
Type = D
Size = 2048
MNP = N
Port Open = N
Lock Lines = N
Description = IceZmodem
Hit Esc and save changes. Exit PCBSETUP. Copy the IceZmodem files
to your PCBoard directory.
Now create a batch file in your pcboard directory called PCBRI.BAT
Place the following line in it:
izm port %1 speed %2 rz %3
Now create a batch file in your pcboard directory called PCBSI.BAT
Place the following line in it:
izm port %1 speed %2 sz %3
If you are using nonstandard COM ports, replace the port command with
the adrirq command.
Setting up IceZmodem with a WWIV BBS
""""""""""""""""""""""""""""""""""""
In INIT, hit 7 for external protocols. Hit I for insert. Enter a
number where you want to insert it.
Description.....: IceZmodem
Xfer Ok.........: 0
Require MNP/LAPM: N
Receive Line....: IZM port %2 speed %1 rz %3
Send Line.......: IZM port %2 speed %1 sz %3
Receive Batch...: IZM port %2 speed %1 rz
Send Batch......: IZM port %2 speed %1 sz @%3
To get the most memory out of a WWIV BBS, you must be using v4.24
or later. This version supports a shrink feature. Load up WWIV.INI
and search for SPAWNOPT[PROT_SINGLE] =NONE
change it to:
SPAWNOPT[PROT_SINGLE] =SHRINK, FILES
Setting up IceZmodem with a Remote Access BBS
"""""""""""""""""""""""""""""""""""""""""""""
Load RACONFIG, go to Manager, Protocols, External, and select an open
protocol slot - Then enter the following information:
Name : IceZmodem
Key : I
Extended control file : No
Batch available : Yes
Status : Always Available
Log file name : DSZ.LOG
Control file name : IZM.CTL
Download command line : \RA\IZM.EXE port *P node *N sz @IZM.CTL *M
Upload command line : \RA\IZM.EXE port *P node *N rz # *M
Download ctl string : @
Upload ctl string :
Download log keyword : z
Upload log keyword : Z
Log : Name word # : 10
Log : Desc word # : 0
Copy your IceZmodem files into your Remote Access (RA) directory.
Now look at the line up above that says "Log file name". You must enter
this filename as the same name you have the environment variable DSZLOG
equal to. For example, if you have SET DSZLOG=DSZLOG.TXT in your batch
files, you must enter DSZLOG.TXT for the Log file name. If you leave
DSZ.LOG alone, you must have SET DSZLOG=DSZ.LOG in your AUTOEXEC.BAT.
The above will work for a single-node system. If you are using a multi-
node system, adjust the parameters appropriately so there are no conflicts.
PLEASE NOTE: If the above command lines do not work, try:
Download command line : \RA\IZM.EXE port *P speed *B node *N sz @IZM.CTL *M
Upload command line : \RA\IZM.EXE port *P speed *B node *N rz # *M