DP Tool Club 15

home *** CD-ROM | disk | FTP | other *** search

/ DP Tool Club 15 / CD_ASCQ_15_070894.iso / maj / 4266 / ports.lst < prev next >

Wrap

File List | 1994-06-05 | 104KB | 2,775 lines

[This file was provided by Wim Osterholt (2:512/56 or wim@djo.wtm.tudelft.nl).] Last Change: 6/5/94 XT, AT and PS/2 I/O port addresses Do NOT consider this information as complete and accurate. If you want to do harware programming check ALWAYS the appropriate data sheets. Be aware that erroneously programming can put your hardware or your data at risk. There is a memory mapped address in use for I/O functions of which I think it should be mentioned here. See at the end of this list. ------------------------------------------------------------------------------- 0000-001F ---- DMA 1 (first Direct Memory Access controller 8237) 0000 r/w DMA channel 0 address byte 0, then byte 1. 0001 r/w DMA channel 0 word count byte 0, then byte 1. 0002 r/w DMA channel 1 address byte 0, then byte 1. 0003 r/w DMA channel 1 word count byte 0, then byte 1. 0004 r/w DMA channel 2 address byte 0, then byte 1. 0005 r/w DMA channel 2 word count byte 0, then byte 1. 0006 r/w DMA channel 3 address byte 0, then byte 1. 0007 r/w DMA channel 3 word count byte 0, then byte 1. 0008 r DMA channel 0-3 status register bit 7 = 1 channel 3 request bit 6 = 1 channel 2 request bit 5 = 1 channel 1 request bit 4 = 1 channel 0 request bit 3 = 1 channel terminal count on channel 3 bit 2 = 1 channel terminal count on channel 2 bit 1 = 1 channel terminal count on channel 1 bit 0 = 1 channel terminal count on channel 0 0008 w DMA channel 0-3 command register bit 7 = 1 DACK sense active high = 0 DACK sense active low bit 6 = 1 DREQ sense active high = 0 DREQ sense active low bit 5 = 1 extended write selection = 0 late write selection bit 4 = 1 rotating priority = 0 fixed priority bit 3 = 1 compressed timing = 0 normal timing bit 2 = 1 enable controller = 0 enable memory-to-memory 0009 w DMA write request register 000A r/w DMA channel 0-3 mask register bit 7-3 = 0 reserved bit 2 = 0 clear mask bit = 1 set mask bit bit 1-0 = 00 channel 0 select = 01 channel 1 select = 10 channel 2 select = 11 channel 3 select 000B w DMA channel 0-3 mode register bit 7-6 = 00 demand mode = 01 single mode = 10 block mode = 11 cascade mode bit 5 = 0 address increment select = 1 address decrement select bit 3-2 = 00 verify operation = 01 write to memory = 10 read from memory = 11 reserved bit 1-0 = 00 channel 0 select = 01 channel 1 select = 10 channel 2 select = 11 channel 3 select 000C w DMA clear byte pointer flip-flop 000D r DMA read temporary register 000D w DMA master clear 000E w DMA clear mask register 000F w DMA write mask register ------------------------------------------------------------------------------- 0010-001F ---- DMA controller (8237) on PS/2 model 60 & 80 ------------------------------------------------------------------------------- 0018 w PS/2 extended function register ------------------------------------------------------------------------------- 001A PS/2 extended function execute ------------------------------------------------------------------------------- 0020-003F ---- PIC 1 (Programmable Interrupt Controller 8259) 0020 w PIC initialization command word ICW1 bit 7-5 = 0 only used in 80/85 mode bit 4 = 1 ICW1 is being issued bit 3 = 0 edge triggered mode = 1 level triggered mode bit 2 = 0 successive interrupt vectors use 8 bytes = 1 successive interrupt vectors use 4 bytes bit 1 = 0 cascade mode = 1 single mode, no ICW3 needed bit 0 = 0 no ICW4 needed = 1 ICW4 needed 0021 w PIC ICW2,ICW3,ICW4 after ICW1 to 0020 ICW2: bit 7-3 = address lines A0-A3 of base vector address for PIC bit 2-0 = reserved ICW3: bit 7-0 = 0 slave controller not attached to corresponding interrupt pin = 1 slave controller attached to corresponding interrupt pin ICW4: bit 7-5 = 0 reserved bit 4 = 0 no special fully-nested mode = 1 special fully-nested mode bit 3-2 = 0x nonbuffered mode = 10 buffered mode/slave = 11 buffered mode/master bit 1 = 0 normal EOI = 1 Auto EOI bit 0 = 0 8085 mode = 1 8086/8088 mode 0021 r/w PIC master interrupt mask register OCW1: bit 7 = 0 enable parallel printer interrupt bit 6 = 0 enable diskette interrupt bit 5 = 0 enable fixed disk interrupt bit 4 = 0 enable serial port 1 interrupt bit 3 = 0 enable serial port 2 interrupt bit 2 = 0 enable video interrupt bit 1 = 0 enable keyboard, mouse, RTC interrupt bit 0 = 0 enable timer interrupt 0020 r PIC interrupt request/in-service registers by OCW3 request register: bit 7-0 = 0 no active request for the corresponding int. line = 1 active request for corresponding interrupt line in-service register: bit 7-0 = 0 corresponding line not currently being serviced = 1 corresponding int. line currently being serviced 0020 w OCW2: bit 7-5 = 000 rotate in auto EOI mode (clear) = 001 nonspecific EOI = 010 no operation = 011 specific EOI = 100 rotate in auto EOI mode (set) = 101 rotate on nonspecific EOI command = 110 set priority command = 111 rotate on specific EOI command bit 4 = 0 reserved bit 3 = 0 reserved bit 2-0 interrupt request to which the command applies 0020 w PIC OCW3 bit 7 = 0 reserved bit 6-5 = 0x no operation = 10 reset special mask = 11 set special mask bit 4 = 0 reserved bit 3 = 1 reserved bit 2 = 0 no poll command = 1 poll command bit 1-0 = 0x no operation = 10 read int.request register on next read at 0020 = 11 read int.in-service register on next read 0020 ------------------------------------------------------------------------------- 0022-002B ---- Intel 82355, part of chipset for 386sx initialisation in POST will disable these addresses, only a hard reset will enable them again. 0022 r/w 82335 MCR memory configuration register 0024 82335 RC1 roll compare register 0026 82335 RC2 roll compare register 0028 82335 CC0 compare register 002A 82335 CC1 compare register values for CC0 and CC1: 00F9,0000 enable range compare CC0 0-512K CC1 disable 00F1,0000 enable range compare CC0 0-1024K CC1 disable 00F1,10F9 enable range compare CC0 0-1M CC1 1M-1M5 00E1,0000 enable range compare CC0 0-2M CC1 disable 00E1,0000 enable range compare CC0 0-2M CC1 disable 00C1,0000 enable range compare CC0 0-4M CC1 disable 00C1,40E1 enable range compare CC0 0-4M CC1 4M-6M 0081,0000 enable range compare CC0 0-8M CC1 disable ------------------------------------------------------------------------------- 0022-0023 ---- Chip Set Data 0022 w index for accesses to data port 0023 r/w chip set data ------------------------------------------------------------------------------- 0022-0023 ---- Cyrix Cx486SLC/DLC processor Cache Configuration Registers 0022 w index for accesses to next port C0h CR0 C1h CR1 C4h non-cacheable region 1, start address bits 31-24 C5h non-cacheable region 1, start address bits 23-16 C6h non-cacheable region 1, start addr 15-12, size (low nybble) C7h non-cacheable region 2, start address bits 31-24 C8h non-cacheable region 2, start address bits 23-16 C9h non-cacheable region 2, start addr 15-12, size (low nybble) CAh non-cacheable region 3, start address bits 31-24 CBh non-cacheable region 3, start address bits 23-16 CCh non-cacheable region 3, start addr 15-12, size (low nybble) CDh non-cacheable region 4, start address bits 31-24 CEh non-cacheable region 4, start address bits 23-16 CFh non-cacheable region 4, start addr 15-12, size (low nybble) 0023 r/w cache configuration register array (indexed by port 0022h) non-cacheable region sizes: 00h disabled 01h 4K 02h 8K 03h 16K 04h 32K 05h 64K 06h 128K 07h 256K 08h 512K 09h 1M 0Ah 2M 0Bh 4M 0Ch 8M 0Dh 16M 0Eh 32M 0Fh 4G Configuration Register 0 format: bit 0 "NC0" first 64K of each 1M noncacheable in real/V86 bit 1 "NC1" 640K-1M noncacheable bit 2 "A20M" enables A20M# input pin bit 3 "KEN" enables KEN# input pin bit 4 "FLUSH" enables KEN# input pin bit 5 "BARB" enables internal cache flushing on bus holds bit 6 "C0" cache direct-mapped instead of 2-way associative bit 7 "SUSPEND" enables SUSP# input and SUSPA# output pins Configuration Register 1 format; bit 0 "RPL" enables output pins RPLSET and RPLVAL# ------------------------------------------------------------------------------- 0026-0027 ---- Power Management 0026 w index for data port 0027 r/w power management data ------------------------------------------------------------------------------- 0038-003F ---- PC radio by CoZet Info Systems The I/O address range is dipswitch selectable from: 038-03F and 0B0-0BF 078-07F and 0F0-0FF 138-13F and 1B0-1BF 178-17F and 1F0-1FF 238-23F and 2B0-2BF 278-27F and 2F0-2FF 338-33F and 3B0-3BF 378-37F and 3F0-3FF All of these addresses show a readout of FF in initial state. Once started, all of the addresses show FB, whatever might happen. ------------------------------------------------------------------------------- 0040-005F ---- PIT (Programmable Interrupt Timer 8253, 8254) XT & AT uses 40-43 PS/2 uses 40, 42,43,44, 47 0040 r/w PIT counter 0, counter divisor (XT, AT, PS/2) 0041 r/w PIT counter 1, RAM refresh counter (XT, AT) 0042 r/w PIT counter 2, cassette & speaker (XT, AT, PS/2) 0043 r/w PIT mode port, control word register for counters 0-2 bit 7-6 = 00 counter 0 select = 01 counter 1 select (not PS/2) = 10 counter 2 select bit 5-4 = 00 counter latch command = 01 read/write counter bits 0-7 only = 10 read/write counter bits 8-15 only = 11 read/write counter bits 0-7 first, then 8-15 bit 3-1 = 000 mode 0 select = 001 mode 1 select - programmable one shot = x10 mode 2 select - rate generator = x11 mode 3 select - square wave generator = 100 mode 4 select - software triggered strobe = 101 mode 5 select - hardware triggered strobe bit 0 = 0 binary counter 16 bits = 1 BCD counter 0044 r/w PIT counter 3 (PS/2, EISA) used as fail-safe timer. generates an NMI on time out. for user generated NMI see at 0462. 0047 w PIT control word register counter 3 (PS/2, EISA) bit 7-6 = 00 counter 3 select = 01 reserved = 10 reserved = 11 reserved bit 5-4 = 00 counter latch command counter 3 = 01 read/write counter bits 0-7 only = 1x reserved bit 3-0 = 00 0048 EISA 0049 8254 timer 2, not used (counter 1) 004A EISA programmable interval timer 2 004B EISA programmable interval timer 2 ------------------------------------------------------------------------------- 0060-006F ---- Keyboard controller (8041, 8042) (or PPI (8255) on XT) XT uses 60-63, AT uses 60-64 AT keyboard controller input port bit definitions bit 7 = 0 keyboard inhibited bit 6 = 0 CGA, else MDA bit 5 = 0 manufacturing jumper installed bit 4 = 0 system RAM 512K, else 640K bit 3-0 reserved AT keyboard controller input port bit definitions by Compaq bit 7 = 0 security lock is locked bit 6 = 0 Compaq dual-scan display, 1=non-Compaq display bit 5 = 0 system board dip switch 5 is ON bit 4 = 0 auto speed selected, 1=high speed selected bit 3 = 0 slow (4MHz), 1 = fast (8MHz) bit 2 = 0 80287 installed, 1= no NDP installed bit 1-0 reserved AT keyboard controller output port bit definitions bit 7 = keyboard data output bit 6 = keyboard clock output bit 5 = 0 input buffer full bit 4 = 0 output buffer empty bit 3 = reserved (see note) bit 2 = reserved (see note) bit 1 = gate A20 bit 0 = system reset Note: bits 2 and 3 are the turbo speed switch or password lock on Award/AMI/Phoenix BIOSes. These bits make use of nonstandard keyboard controller BIOS functionality to manipulate pin 23 (8041 port 22) as turbo switch for AWARD pin 35 (8041 port 15) as turbo switch/pw lock for Phoenix 0060 r/w KB controller data port or keyboard input buffer (ISA, EISA) should only be read from after status port bit0 = 1 should only be written to if status port bit1 = 0 keyboard commands (data also goes to port 0060h): E6 sngl set mouse scaling to 1:1 E7 sngl set mouse scaling to 2:1 E8 dbl set mouse resolution (00h = 1/mm,01h = 2/mm,02h = 4/mm,03h = 8/mm) E9 sngl get mouse information read two status bytes: byte 0 bit 7 unused bit 6 remote rather than stream mode bit 5 mouse enabled bit 4 scaling set to 2:1 bit 3 unused bit 2 left button pressed bit 1 unused bit 0 right button pressed byte 1: resolution ED dbl set/reset mode indicators Caps Num Scrl bit 2 = CapsLk, bit 1 = NumLk, bit 0 = ScrlLk EE sngl diagnostic echo. returns EE. EF sngl NOP (No OPeration). reserved for future use F0 dbl get/set scan code set 00h get current set 01h scancode set 1 (except Type 2 ctrlr) 02h scancode set 2 (default) 03h scancode set 3 F2 sngl read keyboard ID (read two ID bytes) F2 sngl read mouse ID (read two ID bytes) F3 dbl set typematic rate/delay F3 dbl set mouse sample rate in reports per second F4 sngl enable keyboard F4 sngl enable mouse F5 sngl disable keyboard. set default parameters F5 sngl disable mouse, set default parameters F6 sngl set default parameters F7 sngl [MCA] set all keys to typematic (scancode set 3) F8 sngl [MCA] set all keys to make/release F9 sngl [MCA] set all keys to make only FA sngl [MCA] set all keys to typematic/make/release FB sngl [MCA] set al keys to typematic FC dbl [MCA] set specific key to make/release FD dbl [MCA] set specific key to make only FE sngl resend last scancode FF sngl perform internal power-on reset function FF sngl reset mouse Note: must issue command D4h to port 64h first to access mouse functions 0060 r KeyBoard or KB controller data output buffer (via PPI on XT) 0061 w KB controller port B (ISA, EISA) (PS/2 port A is at 0092) system control port for compatibility with 8255 bit 7 (1= IRQ 0 reset ) bit 6-4 reserved bit 3 = 1 channel check enable bit 2 = 1 parity check enable bit 1 = 1 speaker data enable bit 0 = 1 timer 2 gate to speaker enable 0061 r KB controller port B control register (ISA, EISA) system control port for compatibility with 8255 bit 7 parity check occurred bit 6 channel check occurred bit 5 mirrors timer 2 output condition bit 4 toggles with each refresh request bit 3 channel check status bit 2 parity check status bit 1 speaker data status bit 0 timer 2 gate to speaker status 0061 w PPI Programmable Peripheral Interface 8255 (XT only) system control port bit 7 = 1 clear keyboard bit 6 = 0 hold keyboard clock low bit 5 = 0 I/O check enable bit 4 = 0 RAM parity check enable bit 3 = 0 read low switches bit 2 reserved, often used as turbo switch bit 1 = 1 speaker data enable bit 0 = 1 timer 2 gate to speaker enable 0062 r/w PPI (XT only) bit 7 = 1 RAM parity check bit 6 = 1 I/O channel check bit 5 = 1 timer 2 channel out bit 4 reserved bit 3 = 1 system board RAM size type 1 bit 2 = 1 system board RAM size type 2 bit 1 = 1 coprocessor installed bit 0 = 1 loop in POST 0063 r/w PPI (XT only) command mode register (read dipswitches) bit 7-6 = 00 1 diskette drive = 01 2 diskette drives = 10 3 diskette drives = 11 4 diskette drives bit 5-4 = 00 reserved = 01 40*25 color (mono mode) = 10 80*25 color (mono mode) = 11 MDA 80*25 bit 3-2 = 00 256K (using 256K chips) = 01 512K (using 256K chips) = 10 576K (using 256K chips) = 11 640K (using 256K chips) bit 3-2 = 00 64K (using 64K chips) = 01 128K (using 64K chips) = 10 192K (using 64K chips) = 11 256K (using 64K chips) bit 1-0 reserved 0064 r KB controller read status (ISA, EISA) bit 7 = 1 parity error on transmission from keyboard bit 6 = 1 receive timeout bit 5 = 1 transmit timeout bit 4 = 0 keyboard inhibit bit 3 = 1 data in input register is command 0 data in input register is data bit 2 = system flag status 0=power up or reset 1=selftest OK bit 1 = 1 input buffer full (input 60/64 has data for 8042) bit 0 = 1 output buffer full (output 60 has data for system) 0064 r KB controller read status (MCA) bit 7 = 1 parity error on transmission from keyboard bit 6 = 1 general timeout bit 5 = 1 mouse output buffer full bit 4 = 0 keyboard inhibit bit 3 = 1 data in input register is command 0 data in input register is data bit 2 = system flag status 0=power up or reset 1=selftest OK bit 1 = 1 input buffer full (input 60/64 has data for 8042) bit 0 = 1 output buffer full (output 60 has data for system) 0064 r KB controller read status by Compaq bit 7 = 1 parity error detected (11-bit format only). If an error is detected, a Resend command is sent to the keyboard once only, as an attempt to recover. bit 6 = 1 receive timeout. transmission didn't finish in 2mS. bit 5 = 1 transmission timeout error bit 5,6,7 cause 1 0 0 No clock 1 1 0 Clock OK, no response 1 0 1 Clock OK, parity error bit 4 = 0 security lock engaged bit 3 = 1 data in OUTPUT register is command 0 data in OUTPUT register is data bit 2 = 0 system flag status 0=power up or reset 1=soft reset bit 1 = 1 input buffer full (output 60/64 has data) bit 0 = 0 no new data in buffer (input 60 has data) 0064 w KB controller input buffer (ISA, EISA) KB controller commands (data goes to port 0060): 20 read read byte zero of internal RAM, this is the last KB command send to 8041 Compaq Put current command byte on port 0060 command structure: bit 7 reserved bit 6 = 1 convert KB codes to 8086 scan codes bit 5 = 0 use 11-bit codes, 1=use 8086 codes bit 4 = 0 enable keyboard, 1=disable keyboard bit 3 = 1 ignore security lock state bit 2 this bit goes into bit2 status reg. bit 1 = 0 reserved bit 0 = 1 generate int. when output buffer full 21-3F read reads the byte specified in the lower 5 bits of the command in the 8041's internal RAM 60-7F dbl writes the data byte to the address specified in the 5 lower bits of the command. Alternate description KB IO command 60 summary: bit7 = 0 reserved bit6 = IBM PC compatibility mode bit5 = IBM PC mode bit4 = disable kb bit3 = inhibit override bit2 = system flag bit1 = 0 reserved bit0 = enableoutput buffer full interrupt 60 Compaq Load new command (60 to [64], command to [60]) A1 Compaq unknown speedfunction ?? A2 Compaq unknown speedfunction ?? A3 Compaq Enable system speed control A4 MCA check if password installed A4 Compaq Toggle speed A5 MCA load password A5 Compaq Special reed. the 8042 places the real values of port 2 except for bits 4 and 5 wich are given a new definition in the output buffer. No output buffer full is generated. if bit 5 = 0, a 9-bit keyboard is in use if bit 5 = 1, an 11-bit keyboard is in use if bit 4 = 0, outp-buff-full interrupt disabled if bit 4 = 1, output-buffer-full int. enabled A6 MCA check password A6 Compaq unknown speedfunction ?? A7 MCA disable mouse port A8 MCA enable mouse port A9 MCA test mouse port AA sngl initiate self-test. will return 55 to data port Compaq Initializes ports 1 and 2, disables the keyboard and clears the buffer pointers. It then places 55 in the output buffer. AB sngl initiate interface test. result values: 0 = no error 1 = keyboard clock line stuck low 2 = keyboard clock line stuck high 3 = keyboard data line is stuck low 4 = keyboard data line stuck high Compaq 5 = Compaq diagnostic feature AC read diagnostic dump. the contents of the 8041 RAM, output port, input port, status word are send. AD sngl disable keyboard (sets bit 4 of commmand byte) AE sngl enable keyboard (resets bit 4 of commmand byte) AF AWARD Enhanced Command: read keyboard version C0 read read input port Compaq Places status of input port in output buffer. use this command only when the output buffer is empty C1 MCA Enhanced Command: poll input port Low nibble C2 MCA Enhanced Command: poll input port High nibble D0 read read output port Compaq Places byte in output port in output buffer. use this command only when the output buffer is empty D1 dbl write output port. next byte written to 0060 will be written to the 8042 output port; the original IBM AT and many compatibles use bit 1 of the output port to control the A20 gate Compaq The system speed bits are not set by this command use commands A1-A6 (!) for speed functions. D2 MCA Enhanced Command: write keyboard output buffer D3 MCA Enhanced Command: write pointing device out.buf. D4 MCA write to mouse D4 AWARD Enhanced Command: write to auxiliary device DD sngl disable address line A20 (HP Vectra only???) default in Real Mode DF sngl enable address line A20 (HP Vectra only???) E0 read read test inputs. bit0 = kbd clock, bit1 = kbd data Exxx AWARD Enhanced Command: active output port ED Compaq This is a two part command to control the state of the NumLock CpasLock and ScrollLock LEDs The second byte contains the state to set LEDs. bit 7-3 reserved. should be set to 0. bit 2 = 0 Caps Lock LED off bit 1 = 0 Num Lock LED off bit 0 = 0 Scroll Lock LED off F0-FF sngl pulse output port low for 6 microseconds. bits 0-3 contain the mask for the bits to be pulsed. a bit is pulsed if its mask bit is zero. bit0=system reset. Don't set to zero. Pulse only! general note: Keyboard controllers are widely different from each other. You cannot generally exchange them between different machines. note on Award: Derived from Award's Enhanced KB controller advertising sheet. note on Compaq: Derived from the Compaq Deskpro 386 Tech. Ref. Guide. 0065 r communications port (Olivetti M24) 0068 w HP-Vectra control buffer (HP commands) 0069 r HP-Vectra SVC (keyboard request SerViCe port) 006A w HP-Vectra clear processing, done 006C-006F HP-HIL (Human Interface Link = async. serial inputs 0-7) ------------------------------------------------------------------------------- 0065 ---- AT&T 6300+ high/low chip select ------------------------------------------------------------------------------- 0065 ---- ??? 0065 r/w ??? bit 2: A20 gate control (set = A20 enabled, clear = disabled) ------------------------------------------------------------------------------- 0066-0067 ---- AT&T 6300+ system configuration switches ------------------------------------------------------------------------------- 0068 ---- C&T chipsets, turbo mode control ------------------------------------------------------------------------------- 006B-006F ---- SSGA control registers 006B ? RAM enable/remap 006C-006F undocumented ------------------------------------------------------------------------------- 0070-007F ---- CMOS RAM/RTC (Real Time Clock MC146818) 0070 w CMOS RAM index register port (ISA, EISA) bit 7 = 1 NMI disabled = 0 NMI enabled bit 6-0 CMOS RAM index (64 bytes, sometimes 128 bytes) any write to 0070 should be followed by an action to 0071 or the RTC wil be left in an unknown state. 0071 r/w CMOS RAM data port (ISA, EISA) RTC registers: 00 current second in BCD 01 alarm second in BCD 02 current minute in BCD 03 alarm minute in BCD 04 current hour in BCD 05 alarm hour in BCD 06 day of week in BCD 07 day of month in BCD 08 month in BCD 09 year in BCD (00-99) 0A status register A bit 7 = 1 update in progress bit 6-4 divider that identifies the time-based frequency bit 3-0 rate selection output frequency and int. rate 0B status register B bit 7 = 0 run = 1 halt bit 6 = 1 enable periodic interrupt bit 5 = 1 enable alarm interrupt bit 4 = 1 enable update-ended interrupt bit 3 = 1 enable square wave interrupt bit 2 = 1 calendar is in binary format = 0 calendar is in BCD format bit 1 = 1 24-hour mode = 0 12-hour mode bit 0 = 1 enable daylight savings time. only in USA. useless in Europe. Some DOS versions clear this bit when you use the DAT/TIME command. 0C status register C bit 7 = interrupt request flag bit 6 = peridoc interrupt flag bit 5 = alarm interrupt flag bit 4 = update interrupt flag bit 3-0 reserved 0D status register D bit 7 = 1 Real-Time Clock has power bit 6-0 reserved 0E diagnostics status byte bit 7 = 0 RTC lost power bit 6 = 1 CMOS RAM checksum bad bit 5 = 1 invalid configuration information at POST bit 4 = 1 memory size error at POST bit 3 = 1 fixed disk/adapter failed initialization bit 2 = 1 CMOS RAM time found invalid bit 1 = 1 adapters do not match configuration (EISA) bit 0 = 1 time out reading an adapter ID (EISA) 0F shutdown status byte 00 = normal execution of POST 01 = chip set initialization for real mode reentry 04 = jump to bootstrap code 05 = issue an EOI an JMP to Dword ptr at 40:67 06 = JMP to Dword ptrv at 40:67 without EOI 07 = return to INT15/87 (block move) 08 = return to POST memory test 09 = return to INT15/87 (block move) 0A = JMP to Dword ptr at 40:67 without EOI 0B = return IRETS through 40:67 10 diskette drive type for A: and B: bit 7-4 drive type of drive 0 bit 3-0 drive type of drive 1 = 0000 no drive = 0001 360K = 0010 1M2 = 0011 720K = 0100 1M44 = 0101-1111 reserved 11 reserved / AMI Extended CMOS setup (AMI Hi-Flex BIOS) bit 7 = 1 Typematic Rate Programming bit 6-5 = 00 Typematic Rate Delay 250 mSec bit 4-0 = 00011 Typematic Rate 21.8 Chars/Sec 12 fixed disk drive type for drive 0 and drive 1 bit 7-4 drive type of drive 0 bit 3-0 drive type of drive 1 if either of the nibbles equals 0F, then bytes 19 an 1A are valid 13 reserved / AMI Extended CMOS setup (AMI Hi-Flex BIOS) bit 7 = 1 Mouse Support Option bit 6 = 1 Above 1 MB Memory Test disable bit 5 = 1 Memory Test Tick Sound disable bit 4 = 1 Memory Parity Error Check enable bit 3 = 1 Hit <ESC> Message Display disabled bit 2 = 1 Hard Disk Type 47 Data Area at address 0:300 bit 1 = 1 Wait For <F1> If Any Error enabled bit 0 = 1 System Boot Up Num Lock is On 14 equipment byte bit 7-6 diskette drives installed = 00 1 drive installed = 01 2 drives installed = 10 reserved = 11 reserved bit 5-4 primary display = 00 adapter card with option ROM = 01 40*25 color = 10 80*25 color = 11 monochrome bit 3-2 reserved bit 1 = 1 coprocessor installed (non-Weitek) bit 0 diskette drive avaliable for boot 15 LSB of systemn base memory in Kb 16 MSB of systemn base memory in Kb 17 LSB of total extended memory in Kb 18 MSB of total extended memory in Kb 19 drive C extension byte 1A drive D extension byte 1B-27 reserved 1B/1C word to 82335 RC1 roll compare register at [24] (Phoenix) 1D/1E word to 82335 RC2 roll compare register at [26] (Phoenix) 28 HP-Vectra checksum over 29-2D 29-2D reserved 29/2A word to Intel 82335 CC0 compare register at [28](Phoenix) 2B/2C word send to 82335 CC1 compare register at [2A] (Phoenix) 2D AMI Extended CMOS setup (AMI Hi-Flex BIOS) (Phoenix BIOS checks for the values AA or CC) bit 7 = 1 Weitek Processor Absent bit 6 = 1 Floppy Drive Seek At Boot disabled bit 5 = 1 System Boot Up Sequence C:, A: bit 4 = 1 System Boot Up Speed is high bit 3 = 1 Cache Memory enabled bit 2 = 1 Internal Cache Memory <1> bit 1-0 reserved 2E CMOS MSB checksum over 10-2D 2F CMOS LSB checksum over 10-2D 30 LSB of extended memory found above 1Mb at POST 31 MSB of extended memory found above 1Mb at POST 32 date century in BCD 33 information flags bit4 = bit4 from CPU register CR0 (Phoenix) this bit is only known as INTEL RESERVED 34-3F reserved 34 bit4 bit5 (Phoenix BIOS) 3D/3E word to 82335 MCR memory config register at [22](Phoenix) 3D bit3 base memsize 512/640 (Phoenix) 3E bit7 = 1 relocate enable (Phoenix) bit1 = 1 shadow video enable (Phoenix) bit0 = 1 shadow BIOS enable (Phoenix) User Definable Drive Parameters are also stored in CMOS RAM: AMI (386sx BIOS 1989) first user definable drive (type 47) 1B L cylinders 1C H cylinders 1D heads 1E L Write Precompensation Cylinder 1F H Write Precompensation Cylinder 20 ?? 21 L cylinders parking zone 22 H cylinders parking zone 23 sectors AMI (386sx BIOS 1989) second user definable drive (type 48) 24 L cylinders 25 H cylinders 26 heads 27 L Write Precompensation Cylinder 28 H Write Precompensation Cylinder 29 ?? 2A L cylinders parking zone 2B H cylinders parking zone 2C sectors Phoenix (386BIOS v1.10.03 1988) 1st user definable drv (type48) 20 L cylinders 21 H cylinders 22 heads 23 L Write Precompensation Cylinder 24 H Write Precompensation Cylinder 25 L cylinders parking zone 26 H cylinders parking zone 27 sectors Phoenix (386BIOS v1.10.03 1988) 2nd user definable drv (type49) (when PS/2-style password option is not used) 35 L cylinders 36 H cylinders 37 heads 38 L Write Precompensation Cylinder 39 H Write Precompensation Cylinder 3A L cylinders parking zone 3B H cylinders parking zone 3C sectors 0074 w secondary CMOS RAM index (Compaq) 0076 r/w secondary CMOS RAM (Compaq) 0078 HP-Vectra Hard Reset: NMI enable/disable bit 7 = 0 disable & clear hard reset from HP-HIL controller = 1 enable hard reset from HP-HIL controller chip bit 6-0 reserved ------------------------------------------------------------------------------- 0078-007F ---- PC radio by CoZet Info Systems The I/O address range is dipswitch selectable from: 038-03F and 0B0-0BF 078-07F and 0F0-0FF 138-13F and 1B0-1BF 178-17F and 1F0-1FF 238-23F and 2B0-2BF 278-27F and 2F0-2FF 338-33F and 3B0-3BF 378-37F and 3F0-3FF All of these addresses show a readout of FF in initial state. Once started, all of the addresses show FB, whatever might happen. ------------------------------------------------------------------------------- 007C-007D ---- HP-Vectra PIC 3 (Programmable Interrupt Controller 8259) cascaded to first controller. used for keyboard and input device interface. 007C r/w HP-Vectra PIC 3 see at 0020 PIC 1 007D r/w HP-Vectra PIC 3 see at 0021 PIC 1 ------------------------------------------------------------------------------- 0080 w Manufacturing Diagnostics port ------------------------------------------------------------------------------- 0080-008F ---- DMA page registers (74612) 0080 r/w extra page register (temporary storage) 0081 r/w DMA channel 2 address byte 2 0082 r/w DMA channel 3 address byte 2 0083 r/w DMA channel 1 address byte 2 0084 r/w extra page register 0085 r/w extra page register 0086 r/w extra page register 0087 r/w DMA channel 0 address byte 2 0088 r/w extra page register 0089 r/w DMA channel 6 address byte 2 0089 r/w DMA channel 7 address byte 2 0089 r/w DMA channel 5 address byte 2 008C r/w extra page register 008D r/w extra page register 008E r/w extra page register 008F r/w DMA refresh page register ------------------------------------------------------------------------------- 0084 ---- Compaq POST Diagnostic ------------------------------------------------------------------------------- 0084 ---- EISA Synchronize Bus Cycle ------------------------------------------------------------------------------- 0090-009F ---- PS/2 POS (Programmable Option Select) 0090 Central arbitration control port 0091 r Card selection feedback 0092 r/w PS/2 system control port A (port B is at 0061) bit 7-6 any bit set to 1 turns activity light on bit 5 reserved bit 4 = 1 watchdog timout occurred bit 3 = 0 RTC/CMOS security lock (on password area) unlocked = 1 CMOS locked (done by POST) bit 2 reserved bit 1 = 1 indicates A20 active bit 0 = 0 system reset or write 1 pulse alternate reset pin (alternate CPU reset) 0094 w system board enable/setup register bit 7 = 1 enable functions = 0 setup functions bit 5 = 1 enables VGA = 0 setup VGA 0095 reserved 0096 w adapter enable /setup register bit 3 = 1 setup adapters = 0 enable registers 0097 reserved ------------------------------------------------------------------------------- 00A0-00AF ---- PIC 2 (Programmable Interrupt Controller 8259) 00A0 r/w NMI mask register (XT) 00A0 r/w PIC 2 same as 0020 for PIC 1 00A1 r/w PIC 2 same as 0021 for PIC 1 except for OCW1: bit 7 = 0 reserved bit 6 = 0 enable fixed disk interrupt bit 5 = 0 enable coprocessor exception interrupt bit 4 = 0 enable mouse interrupt bit 3 = 0 reserved bit 2 = 0 reserved bit 1 = 0 enable redirect cascade bit 0 = 0 enable real-time clock interrupt ------------------------------------------------------------------------------- 00B0-00BF ---- PC radio by CoZet Info Systems The I/O address range is dipswitch selectable from: 038-03F and 0B0-0BF 078-07F and 0F0-0FF 138-13F and 1B0-1BF 178-17F and 1F0-1FF 238-23F and 2B0-2BF 278-27F and 2F0-2FF 338-33F and 3B0-3BF 378-37F and 3F0-3FF All of these addresses show a readout of FF in initial state. Once started, all of the addresses show FB, whatever might happen. ------------------------------------------------------------------------------- 00C0 ---- TI SN746496 programmable tone/noise generator PCjr ------------------------------------------------------------------------------- 00C0-00DF ---- DMA 2 (second Direct Memory Access controller 8237) 00C0 r/w DMA channel 4 memory address bytes 1 and 0 (low) (ISA, EISA) 00C2 r/w DMA channel 4 transfer count bytes 1 and 0 (low) (ISA, EISA) 00C4 r/w DMA channel 5 memory address bytes 1 and 0 (low) (ISA, EISA) 00C6 r/w DMA channel 5 transfer count bytes 1 and 0 (low) (ISA, EISA) 00C8 r/w DMA channel 6 memory address bytes 1 and 0 (low) (ISA, EISA) 00CA r/w DMA channel 6 transfer count bytes 1 and 0 (low) (ISA, EISA) 00CC r/w DMA channel 7 memory address byte 0 (low), then 1 (ISA, EISA) 00CE r/w DMA channel 7 transfer count byte 0 (low), then 1 (ISA, EISA) 00D0 r DMA channel 4-7 status register (ISA, EISA) bit 7 = 1 channel 7 request bit 6 = 1 channel 6 request bit 5 = 1 channel 5 request bit 4 = 1 channel 4 request bit 3 = 1 terminal count on channel 7 bit 2 = 1 terminal count on channel 6 bit 1 = 1 terminal count on channel 5 bit 0 = 1 terminal count on channel 4 00D0 w DMA channel 4-7 command register (ISA, EISA) bit 7 = 1 DACK sense active high = 0 DACK sense active low bit 6 = 1 DREQ sense active high = 0 DREQ sense active low bit 5 = 1 extended write selection = 0 late write selection bit 4 = 1 rotating priority = 0 fixed priority bit 3 = 1 compressed timing = 0 normal timing bit 2 = 0 enable controller bit 1 = 1 enable memory-to-memory transfer bit 0 ..... 00D2 w DMA channel 4-7 write request register (ISA, EISA) 00D4 w DMA channel 4-7 write single mask register (ISA, EISA) bit 7-3 reserved bit 2 = 0 clear mask bit = 1 set mask bit bit 1-0 = 00 channel 4 select = 01 channel 5 select = 10 channel 6 select = 11 channel 7 select 00D6 w DMA channel 4-7 mode register (ISA, EISA) bit 7-6 = 00 demand mode = 01 single mode = 10 block mode = 11 cascade mode bit 5 = 0 address increment select = 1 address decrement select bit 4 = 0 autoinitialisation disable = 1 autoinitialisation enable bit 3-2 = 00 verify operation = 01 write to memory = 10 read from memory = 11 reserved bit 1-0 = 00 channel 4 select = 01 channel 5 select = 10 channel 6 select = 11 channel 7 select 00D8 w DMA channel 4-7 clear byte pointer flip-flop (ISA, EISA) 00DA r DMA channel 4-7 read temporary register (ISA, EISA) 00DA w DMA channel 4-7 master clear (ISA, EISA) 00DC w DMA channel 4-7 clear mask register (ISA, EISA) 00DE w DMA channel 4-7 write mask register (ISA, EISA) ------------------------------------------------------------------------------- 00E0-00E7 ---- Microchannel 00E0 r/w split address register, memory encoding registers PS/2m80 only 00E1 r/w memory register 00E3 r/w error trace 00E4 r/w error trace 00E5 r/w error trace 00E7 r/w error trace ------------------------------------------------------------------------------- 00F0-00F5 ---- PCjr Disk Controller 00F0 disk controller 00F2 disk controller control port 00F4 disk controller status register 00F5 disk controller data port ------------------------------------------------------------------------------- 00F0-00FF ---- coprocessor (8087..80387) 00F0 w math coprocessor clear busy latch 00F1 w math coprocessor reset 00F8 r/w opcode transfer 00FA r/w opcode transfer 00FC r/w opcode transfer ------------------------------------------------------------------------------- 00F9-00FF ---- PC radio by CoZet Info Systems The I/O address range is dipswitch selectable from: 038-03F and 0B0-0BF 078-07F and 0F0-0FF 138-13F and 1B0-1BF 178-17F and 1F0-1FF 238-23F and 2B0-2BF 278-27F and 2F0-2FF 338-33F and 3B0-3BF 378-37F and 3F0-3FF All of these addresses show a readout of FF in initial state. Once started, all of the addresses show FB, whatever might happen. ------------------------------------------------------------------------------- 0100-010F ---- CompaQ Tape drive adapter. alternate address at 0300 ------------------------------------------------------------------------------- 0100-0107 ---- PS/2 POS (Programmable Option Select) 0100 r POS register 0 Low adapter ID byte 0101 r POS register 1 High adapter ID byte 0102 r/w POS register 2 option select data byte 1 bit 0 is card enable (CDEN) 0103 r/w POS register 3 option select data byte 2 0104 r/w POS register 4 option select data byte 3 0105 r/w POS register 5 option select data byte 4 bit 7 channel active (-CHCK) bit 6 channel status 0106 r/w POS register 6 Low subaddress extension 0107 r/w POS register 7 High subaddress extension ------------------------------------------------------------------------------- 0108-010F ---- 8 digit LED info panel on IBM PS/2 010F w leftmost character on display 010E w second character .... w 0108 w eighth character ------------------------------------------------------------------------------- 0130-013F ---- CompaQ SCSI adapter. alternate address at 0330 ------------------------------------------------------------------------------- 0130-0133 ---- Adaptec 154xB/154xC SCSI adapter. alternate address at 0134, 0230, 0234, 0330 and 0334 ------------------------------------------------------------------------------- 0134-0137 ---- Adaptec 154xB/154xC SCSI adapter. alternate address at 0130, 0230, 0234, 0330 and 0334 ------------------------------------------------------------------------------- 0138-013F ---- PC radio by CoZet Info Systems The I/O address range is dipswitch selectable from: 038-03F and 0B0-0BF 078-07F and 0F0-0FF 138-13F and 1B0-1BF 178-17F and 1F0-1FF 238-23F and 2B0-2BF 278-27F and 2F0-2FF 338-33F and 3B0-3BF 378-37F and 3F0-3FF All of these addresses show a readout of FF in initial state. Once started, all of the addresses show FB, whatever might happen. ------------------------------------------------------------------------------- 0140-014F ---- SCSI (alternate Small Computer System Interface) adapter (1st at 0340-034F) ------------------------------------------------------------------------------- 0140-0157 ---- RTC (alternate Real Time Clock for XT) (1st at 0340-0357) ------------------------------------------------------------------------------- 0170-0177 ---- HDC 2 (2nd Fixed Disk Controller) same as 01Fx (ISA, EISA) ------------------------------------------------------------------------------- 0178-0179 ---- Power Management 0178 w index selection for data port 0179 r/w power management data ------------------------------------------------------------------------------- 0178-017F ---- PC radio by CoZet Info Systems The I/O address range is dipswitch selectable from: 038-03F and 0B0-0BF 078-07F and 0F0-0FF 138-13F and 1B0-1BF 178-17F and 1F0-1FF 238-23F and 2B0-2BF 278-27F and 2F0-2FF 338-33F and 3B0-3BF 378-37F and 3F0-3FF All of these addresses show a readout of FF in initial state. Once started, all of the addresses show FB, whatever might happen. ------------------------------------------------------------------------------- 01E8-01EF ---- System Control. Laptop chipset: Headland HL21 & Acer M5105 01ED r/w select internal register. Data to/from 01EF 01EE r 01EF r/w reg. 5 = 1000xxxx for low CPU clock speed (4MHz on Morse/Mitac) = 0xxxxxxx for high CPU clock speed (16MHz on Morse/Mitac) ------------------------------------------------------------------------------- 01F0-01F7 ---- HDC 1 (1st Fixed Disk Controller) same as 017x (ISA, EISA) 01F0 r/w data register 01F1 r error register diagnostic mode errors: bit 7-3 reserved bit 2-1 = 001 no error detected = 010 formatter device error = 011 sector buffer error = 100 ECC circuitry error = 101 controlling microprocessor error operation mode: bit 7 = 1 bad block detected = 0 block OK bit 6 = 1 uncorrectable ECC error = 0 no error bit 5 reserved bit 4 = 1 ID found = 0 ID not found bit 3 reserved bit 2 = 1 command completed = 0 command aborted bit 1 = 1 track 000 not found = 0 track 000 found bit 0 = 1 DAM not found = 0 DAM found (CP-3022 always 0) 01F1 w WPC/4 (Write Precompensation Cylinder divided by 4) 01F2 r/w sector count 01F3 r/w sector number 01F4 r/w cylinder low 01F5 r/w cylinder high 01F6 r/w drive/head bit 7 = 1 bit 6 = 0 bit 5 = 1 bit 4 = 0 drive 0 select = 1 drive 1 select bit 3-0 head select bits 01F7 r status register bit 7 = 1 controller is executing a command bit 6 = 1 drive is ready bit 5 = 1 write fault bit 4 = 1 seek complete bit 3 = 1 sector buffer requires servicing bit 2 = 1 disk data read successfully corrected bit 1 = 1 index - set to 1 each disk revolution bit 0 = 1 previous command ended in an error 01F7 w command register commands: 98 E5 check power mode (IDE) 90 execute drive diagnostics 50 format track EC identify drive (IDE) 97 E3 idle (IDE) 95 E1 idle immediate (IDE) 91 initialize drive parameters 1x recalibrate E4 read buffer (IDE) C8 read DMA with retry (IDE) C9 read DMA without retry (IDE) C4 read multiplec (IDE) 20 read sectors with retry 21 read sectors without retry 22 read long with retry 23 read long without retry 40 read verify sectors with retry 41 read verify sectors without retry 7x seek EF set features (IDE) C6 set multiple mode (IDE) 99 E6 set sleep mode (IDE) 96 E2 standby (IDE) 94 E0 standby immediate (IDE) E8 write buffer (IDE) CA write DMA with retry (IDE) CB write DMA with retry (IDE) C5 write multiple (IDE) E9 write same (IDE) 30 write sectors with retry 31 write sectors without retry 32 write long with retry 33 write long without retry 3C write verify (IDE) 9A vendor unique (IDE) C0-C3 vendor unique (IDE) 8x vendor unique (IDE) F0-F4 EATA standard (IDE) F5-FF vendor unique (IDE) ------------------------------------------------------------------------------- 01F8 ---- ??? 01F8 r/w ??? bit 0: A20 gate control (set = A20 enabled, clear = disabled) ------------------------------------------------------------------------------- 01F9-01FF ---- PC radio by CoZet Info Systems The I/O address range is dipswitch selectable from: 038-03F and 0B0-0BF 078-07F and 0F0-0FF 138-13F and 1B0-1BF 178-17F and 1F0-1FF 238-23F and 2B0-2BF 278-27F and 2F0-2FF 338-33F and 3B0-3BF 378-37F and 3F0-3FF All of these addresses show a readout of FF in initial state. Once started, all of the addresses show FB, whatever might happen. ------------------------------------------------------------------------------- 0200-020F ---- Game port reserved I/O address space 0200-0207 ---- Game port, eight identical addresses on some boards 0201 r read joystick position and status bit 7 status B joystick button 2 / D paddle button bit 6 status B joystick button 1 / C paddle button bit 5 status A joystick button 2 / B paddle button bit 4 status A joystick button 1 / A paddle button bit 3 B joystick Y coordinate / D paddle coordinate bit 2 B joystick X coordinate / C paddle coordinate bit 1 A joystick Y coordinate / B paddle coordinate bit 0 A joystick X coordinate / A paddle coordinate w fire joysticks four one-shots ------------------------------------------------------------------------------- 0200-02FF ---- Sunshine uPW48, programmer for EPROM version CPU's 8748/8749 (4 bit DIP switch installable in the range 20x-2Fx) 0200-0203 adresses of the 8255 on the uPW48 0208-020B adresses of ??? on the uPW48 (all showing zeros) ------------------------------------------------------------------------------- 0210-0217 ---- Expansion unit (XT) 0210 w latch expansion bus data r verify expansion bus data 0211 w clear wait, test latch r High byte data address 0212 r Low byte data address 0213 w 0=enable, 1=disable expansion unit 0214 w latch data (receiver card port) r read data (receiver card port) 0215 r High byte of address, then Low byte (receiver card port) ------------------------------------------------------------------------------ 0220-0223 ---- Sound Blaster / Adlib port 0220 r/w Left speaker -- Status / Address port 0221 w Left speaker -- Data port 0222 r/w Right speaker -- Status / Address port Address: 01 -- Enable waveform control 02 -- Timer #1 data 03 -- Timer #2 data 04 -- Timer control flags 08 -- Speech synthesis mode 20-35 -- Amplitude Modulation / Vibrato 40-55 -- Level key scaling / Total level 60-75 -- Attack / Decay rate 80-95 -- Sustain / Release rate A0-B8 -- Octave / Frequency Number C0-C8 -- Feedback / Algorithm E0-F5 -- Waveform Selection 0223 w Right speaker -- Data port SeeAlso: 0388-0389 ------------------------------------------------------------------------------- 0220-0227 ---- Soundblaster PRO and SSB 16 ASP ------------------------------------------------------------------------------- 0220-022F ---- Soundblaster PRO 2.0 ------------------------------------------------------------------------------- 0220-022F ---- Soundblaster PRO 4.0 0220 r left FM status port 0220 w left FM music register address port (index) 0221 r/w left FM music data port 0222 r right FM status port 0222 w right FM music register address port (index) 0223 r/w right FM music data port 0224 w mixer register address port (index) 0225 r/w mixer data port 0226 w DSP reset 0228 r FM music status port 0228 w FM music register address port (index) 0229 w FM music data port 022A r DSP read data (voice I/O and Midi) 022C w DSP write data / write command 022C r DSP write buffer status (bit 7) 022E r DSP data available status (bit 7) The FM music is accessible on 0388/0389 for compatibility. ------------------------------------------------------------------------------- 0230-0233 ---- Adaptec 154xB/154xC SCSI adapter. alternate address at 0130, 0134, 0230, 0330 and 0334 ------------------------------------------------------------------------------- 0234-0237 ---- Adaptec 154xB/154xC SCSI adapter. alternate address at 0130, 0134, 0230, 0330 and 0334 ------------------------------------------------------------------------------- 0240-0257 ---- RTC (alternate Real Time Clock for XT) (1st at 0340-0357) (used by TIMER.COM v1.2 which is the 'standard' timer program) ------------------------------------------------------------------------------- 0258-025F ---- Intel Above Board ------------------------------------------------------------------------------- 0278-027E ---- parallel printer port, same as 0378 and 03BC 0278 w data port 0279 r/w status port 027A r/w control port ------------------------------------------------------------------------------- 02A0-02A7 ---- Sunshine EW-901BN, EW-904BN EPROM writer card (release 1986) for EPROMs up to 27512 02A0-02A3 adresses of the 8255 on the EW-90xBN ------------------------------------------------------------------------------- 02A2-02A3 ---- MSM58321RS clock ------------------------------------------------------------------------------- 02B0-02BF ---- Trantor SCSI adapter ------------------------------------------------------------------------------- 02B0-02DF ---- alternate EGA, primary EGA at 03C0 ------------------------------------------------------------------------------- 02C0-02Cx ---- AST-clock ------------------------------------------------------------------------------- 02E0-02EF ---- GPIB (General Purpose Interface Bus, IEEE 488 interface) (GAB 0 on XT) 02E1 GPIB (adapter 0) 02E2 02E3 ------------------------------------------------------------------------------- 02E0-02EF ---- data aquisition (AT) 02E2 data aquisition (adapter 0) 02E3 data aquisition (adapter 0) ------------------------------------------------------------------------------- 02E8 ---- S3 86C928 video controller (ELSA Winner 1000) ------------------------------------------------------------------------------- 02E8-02EF ---- serial port, same as 02F8, 03E8 and 03F8 ------------------------------------------------------------------------------- 02E8-02EF ---- used by ATI Mach32 video cards (e.g. Graphics Ultra+) ------------------------------------------------------------------------------- 02EA ---- S3 86C928 video controller (ELSA Winner 1000) ------------------------------------------------------------------------------- 02F8-02FF ---- serial port, same as 02E8, 03E8 and 03F8 02F8 w transmitter holding register 02F8 r receiver buffer register r/w divisor latch, low byte when DLAB=1 02F9 r/w divisor latch, high byte when DLAB=1 r/w interrupt enable register when DLAB=0 02FA r interrupt identification register 02FB r/w line control register 02FC r/w modem control register 02FD r line status register 02FF r/w scratch register ------------------------------------------------------------------------------- 0300 ---- Award POST Diagnostic ------------------------------------------------------------------------------- 0300-0301 ---- Soundblaster 16 ASP MPU-Midi ------------------------------------------------------------------------------- 0300-0303 ---- Panasonic 52x CD-ROM SCSI Miniport Alternate addresses at 0320, 0340, 0360, and 0380 ------------------------------------------------------------------------------- 0300-031F ---- prototype cards Periscope hardware debugger ------------------------------------------------------------------------------- 0300-030F ---- Philips CD-ROM player CM50 ------------------------------------------------------------------------------- 0300-030F ---- CompaQ Tape drive adapter. alternate address at 0100 ------------------------------------------------------------------------------- 0310-031F ---- Philips CD-ROM player CM50 ------------------------------------------------------------------------------- 0320-0323 ---- XT HDC 1 (Hard Disk Controller) 0320 r/w data register 0321 w reset controller r read controller hardware status bit 7-6 = 0 bit 5 logical unit number bit 4-2 = 0 bit 1 = 0 no error bit 0 = 0 0322 r read DIPswitch setting on XT controller card w generate controller-select pulse 0323 w write pattern to DMA and INT mask register 0324-0327 ---- XT HDC 2 (Hard Disk Controller) 0328-032B ---- XT HDC 3 (Hard Disk Controller) 032C-032F ---- XT HDC 4 (Hard Disk Controller) ------------------------------------------------------------------------------- 0330-0331 ---- MIDI interface ------------------------------------------------------------------------------- 0330-0333 ---- Adaptec 154xB/154xC SCSI adapter. default address. alternate address at 0130, 0134, 0230, 0234 and 0334 ------------------------------------------------------------------------------- 0330-033F ---- CompaQ SCSI adapter. alternate address at 0130 ------------------------------------------------------------------------------- 0330-033F ---- Philips CD-ROM player CM50 ------------------------------------------------------------------------------- 0334-0337 ---- Adaptec 154xB/154xC SCSI adapter. alternate address at 0130, 0134, 0230, 0234 and 0330 ------------------------------------------------------------------------------- 0338 ---- AdLib soundblaster card ------------------------------------------------------------------------------- 0340-034F ---- Philips CD-ROM player CM50 ------------------------------------------------------------------------------- 0340-034F ---- SCSI (1st Small Computer System Interface) adapter (alternate at 0140-014F) ------------------------------------------------------------------------------- 0340-0357 ---- RTC (1st Real Time Clock for XT), (alternate at 0240-0257) (used by TIMER.COM v1.2 which is the 'standard' timer program) 0340 r/w 0.01 seconds 0-99 0341 r/w 0.1 seconds 0-99 0342 r/w seconds 0-59 0343 r/w minutes 0-59 0343 r/w hours 0-23 0345 r/w day of week 1-7 0346 r/w day of month 1-31 0347 r/w month 1-12 0348 0349 r/w year 0-99 034A 034B 034C 034D 034E 034F 0350 r status? 0351 0352 0353 0354 r status? 0355 0356 0357 ------------------------------------------------------------------------------- 0348-0357 ---- DCA 3278 ------------------------------------------------------------------------------- 0360-036F ---- PC network (AT) 0360-0367 ---- PC network (XT only) ------------------------------------------------------------------------------- 0360-036F ---- National Semiconductor DP8390C/NS3249C network chipset Note: cards based on this IEEE 802.3 networking chipset can use any range of 16 consecutive addresses, and provide a total of four pages of sixteen register Page 0 r w 00 Command reg. CR Command reg. CR 01 current local DMA address 0 CLDA0 page start reg. PSTART 02 current local DMA address 1 CLDA1 page stop reg. PSTOP 03 boundary pointer BNRY boundary pointer BNRY 04 transmit status reg. TSR Tx page start address TPSR 05 number of collisions reg. NCR Tx byte count reg.0 TBCR0 06 FIFO Tx byte count reg.1 TBCR1 07 interrupt status reg. ISR interrupt status reg. ISR 08 current remote DMA address 0 CRDA0 remote start addr.reg.0 RSAR0 09 current remote DMA address 1 CRDA1 remote start addr.reg.1 RSAR1 0A reserved remote byte count reg.0 RBCR0 0B reserved remote byte count reg.1 RBCR1 0C receive status reg. RSR Rx configuration reg. RCR 0D tally counter 0 (frame errors) CNTR0 Tx configuration reg. TCR 0E tally counter 1 (CRC errors) CNTR1 data configuration reg. DCR 0F tally counter 2 (missed pkt) CNTR2 interrupt mask reg. IMR Page 1 r/w 00 Command CR 01 physical address reg.0 PAR0 02 physical address reg.1 PAR1 03 physical address reg.2 PAR2 04 physical address reg.3 PAR3 05 physical address reg.4 PAR4 06 physical address reg.5 PAR5 07 current page reg. CURR 08 multicast address reg.0 MAR0 09 multicast address reg.1 MAR1 0A multicast address reg.2 MAR2 0B multicast address reg.3 MAR3 0C multicast address reg.4 MAR4 0D multicast address reg.5 MAR5 0E multicast address reg.6 MAR6 0F multicast address reg.7 MAR7 Page 2 r w diagnostics page - should never be modfied under normal operation. 00 Command CR Command CR 01 page start reg. PSTART current local DMA addr.0 CLDA0 02 page stop reg. BPSTOP current local DMA addr.1 CLDA1 03 remote next packet pointer remote next packet pointer 04 Tx page start address TPSR reserved 05 local next packet pointer local next packet pointer 06 address counter (upper) address counter (upper) 07 address counter (lower) address counter (lower) 08 reserved reserved 09 reserved reserved 0A reserved reserved 0B reserved reserved 0C Rx configuration reg. RCR reserved 0D Tx configuration reg. TCR reserved 0E data configuration reg. DCR reserved 0F interrupt mask reg. IMR reserved Page 3 r w Test Page - should never be modified ! 00 Command CR Command CR bit0=1 software reset command. 1=offline 0=online bit1=0 activate NIC after reset command bit2=1 start transmision of a packet bit3-5 remote DMA command 000 not allowed 001 remote read 010 remote write 011 send packet 1xx abort/complete rmote DMA bit 6,7 page select 00 register page 0 01 register page 1 10 register page 2 11 register page 3 ------------------------------------------------------------------------------- 0370-0377 ---- FDC 2 (2nd Floppy Disk Controller 8272) same as 03F0 0372 w diskette controller DOR (Digital Output Register) 0374 r diskette controller status register 0375 r/w diskette controller data register 0376 r/w FIXED disk controller data register 0377 r diskette controller DIR (Digital Input Register) 0377 w select register for diskette data transfer rate ------------------------------------------------------------------------------- 0378-037A ---- parallel printer port, same as 0278 and 03BC 0378 w data port 0379 r/w status port 037A r/w control port ------------------------------------------------------------------------------- 0380-038F ---- 2nd Binary Synchronous Data Link Control adapter (see 03A0) 0380 r/w on board 8255 port A, internal/external sense 0381 r/w on board 8255 port B, external modem interface 0382 r/w on board 8255 port C, internal control and gating 0383 r/w on board 8255 mode register 0384 r/w on board 8253 channel square wave generator 0385 r/w on board 8253 channel 1 inactivity time-out 0386 r/w on board 8253 channel 2 inactivity time-out 0387 r/w on board 8253 mode register 0388 r/w on board 8273 read: status write: command 0389 r/w on board 8273 read: response write: parameter 038A r/w on board 8273 transmit interrupt status 038B r/w on board 8273 receiver interrupt status 038C r/w on board 8273 data ------------------------------------------------------------------------------ 0388-0389 ---- Sound Blaster / Adlib port 0388 r/w Both Speakers -- Status / Address port Address: 01 -- Enable waveform control 02 -- Timer #1 data 03 -- Timer #2 data 04 -- Timer control flags 08 -- Speech synthesis mode 20-35 -- Amplitude Modulation / Vibrato 40-55 -- Level key scaling / Total level 60-75 -- Attack / Decay rate 80-95 -- Sustain / Release rate A0-B8 -- Octave / Frequency Number C0-C8 -- Feedback / Algorithm E0-F5 -- Waveform Selection 0389 w Data port SeeAlso: 0220-0223 ------------------------------------------------------------------------------- 0388-0389 ---- Soundblaster PRO FM-Chip 0388-038B ---- Soundblaster 16 ASP FM-Chip ------------------------------------------------------------------------------- 0390-0397 ---- Sunshine EW-901B, EW-904B EPROM writer card for EPROMs up to 27512 0390-0393 adresses of the 8255 on the EW-90xB ------------------------------------------------------------------------------- 0390-039F ---- Cluster adapter (AT) 0390-0393 (adapter 0) (XT) ------------------------------------------------------------------------------- 03A0-03AF ---- 1st SDLC (Binary Synchronous Data Link Control adapter) 03A0 r/w on board 8255 port A, internal/external sense 03A1 r/w on board 8255 port B, external modem interface 03A2 r/w on board 8255 port C, internal control and gating 03A3 r/w on board 8255 mode register 03A4 r/w on board 8253 counter 0 unused 03A5 r/w on board 8253 channel 1 inactivity time-out 03A6 r/w on board 8253 channel 2 inactivity time-out 03A7 r/w on board 8253 mode register 03A8 r/w on board 8251 data 03A9 r/w on board 8251 command/mode/status register ------------------------------------------------------------------------------- 03B0-03BF ---- MDA (Monochrome Display Adapter based on 6845) 03B0 same as 03B4 03B1 same as 03B5 03B2 same as 03B4 03B3 same as 03B5 03B4 w MDA CRT index register (EGA/VGA) selects which register (0-11h) is to be accessed through 3B5 03B5 r/w MDA CRT data register (EGA/VGA) selected by port 3B4. registers C-F may be read 00 horizontal total 01 horizontal displayed 02 horizontal sync position 03 horizontal sync pulse width 04 vertical total 05 vertical displayed 06 vertical sync position 07 vertical sunc pulse width 08 interlace mode 09 maximum scan lines 0A cursor start 0B cursor end 0C start address high 0D start address low 0E cursor location high 0F cursor location low 10 light pen high 11 light pen low 03B6 same as 03B4 03B7 same as 03B5 03B8 r/w MDA mode control register bit 7 not used bit 6 not used bit 5 enable blink bit 4 not used bit 3 video enable bit 2 not used bit 1 not used bit 0 high resolution mode 03B9 reserved for color select register on color adapter 03BA r CRT status register EGA/VGA: input status 1 register bit 7 (MSD says) if this bit changes within 8000h reads then bit 6-4 = 000 = adapter is Hercules or compatible 001 = adapter is Hercules+ 101 = adapter is Hercules InColor else: adapter is unknown bit 3 black/white video bit 2-1 reserved bit 0 horizontal drive 03BA w EGA/VGA feature control register 03BB reserved for light pen strobe reset ------------------------------------------------------------------------------- 03BC-03BF ---- parallel printer port, same as 0278 and 0378 03BC w data port 03BD r/w status port bit 7 = 0 busy bit 6 = 0 acknowledge bit 5 = 1 out of paper bit 4 = 1 printer is selected bit 3 = 0 error bit 2 = 0 IRQ has occurred bit 1-0 reserved 03BE r/w control port bit 7-5 reserved bit 4 = 1 enable IRQ bit 3 = 1 select printer bit 2 = 0 initialize printer bit 1 = 1 automatic line feed bit 0 = 1 strobe ------------------------------------------------------------------------------- 03BF r/w Hercules configuration switch register bit 7-2 bit 1 = 0 disables upper 32K of graphics mode buffer 1 enables upper 32K of graphics mode buffer bit 0 = 0 prevents graphics mode 1 allows graphics mode ------------------------------------------------------------------------------- 03C0-03C7 ---- Sunshine EW-901, EW-901A, EW-904, EW-904A EPROM writer card for EPROMs up to 27512 03C0-03C3 adresses of the 8255 on the EW-90x ------------------------------------------------------------------------------- 03C0-03CF ---- EGA (1st Enhanced Graphics Adapter) alternate at 02C0 03C0 (r)/w EGA VGA ATC index/data register 03C1 r VGA other attribute register 03C2 r EGA VGA input status 0 register w VGA miscellaneous output register 03C3 r/w VGA video subsystem enable (see also port 46E8h) for IBM, motherboard VGA only 03C4 w EGA TS index register r/w VGA sequencer index register 03C5 w EGA TS data register r/w VGA other sequencer register 03C6 r/w VGA PEL mask register 03C7 r/w VGA PEL address read mode r VGA DAC state register 03C8 r/w VGA PEL address write mode 03C9 r/w VGA PEL data register 03CA w EGA graphics 2 position register r VGA feature control register 03CC w EGA graphics 1 position register r VGA miscellaneous output register 03CE w EGA GDC index register r/w VGA graphics address register 03CF w EGA GDC data register r/w VGA other graphics register ------------------------------------------------------------------------------- 03D0-03DF ---- CGA (Color Graphics Adapter) 03D0 same as 03D4 03D1 same as 03D5 03D2 same as 03D4 03D3 same as 03D5 03D4 w CRT (6845) index register (EGA/VGA) selects which register (0-11h) is to be accessed through 3B5 03D5 w CRT (6845) data register (EGA/VGA) selected by port 3B4. registers C-F may be read (for registers see at 3B5) 03D6 same as 03D4 03D7 same as 03D5 03D8 r/w CGA mode control register (except PCjr) bit 7-6 not used bit 5 = 1 blink enabled bit 4 = 1 640*200 graphics mode bit 3 = 1 video enabled bit 2 = 1 monochrome signal bit 1 = 0 text mode = 1 320*200 graphics mode bit 0 = 0 40*25 text mode = 1 80*25 text mode 03D9 r/w CGA palette register bit 7-6 not used bit 5 = 0 active color set: red, green brown = 1 active color set: cyan, magenta, white bit 4 intense colors in graphics, background colors text bit 3 intense border in 40*25, intense background in 320*200, intense foreground in 640*200 bit 2 red border in 40*25, red background in 320*200, red foreground in 640*200 bit 1 green border in 40*25, green background in 320*200, green foreground in 640*200 bit 0 blue border in 40*25, blue background in 320*200, blue foreground in 640*200 03DA r CGA status register EGA/VGA: input status 1 register bit 7-4 not used bit 3 = 1 in vertical retrace bit 2 = 1 light pen switch is off bit 1 = 1 positive edge from light pen has set trigger bit 0 = 0 do not use memory = 1 memory access without interfering with display 03DA w EGA/VGA feature control register 03DB w clear light pen latch 03DC r/w preset light pen latch 03DF CRT/CPU page register (PCjr only) ------------------------------------------------------------------------------- 03E8-03EF ---- serial port, same as 02E8, 02F8 and 03F8 ------------------------------------------------------------------------------- 03F0-03F7 ---- FDC 1 (1st Floppy Disk Controller 8272) same as 0370 03F0 diskette controller status A (PS/2) bit 7 interrupt pending bit 6 second drive installed bit 5 step bit 4 track 0 bit 3 head 1 select bit 2 index bit 1 write protect bit 0 direction 03F1 r diskette controller status B (PS/2) bit 7-6 reserved bit 5 drive select (0=A:, 1=B:) bit 4 write data bit 3 read data bit 2 write enable bit 1 motor enable 1 bit 0 motor enable 0 03F2 w diskette controller DOR (Digital Output Register) bit 7-6 reserved PS/2 bit 7 = 1 drive 3 motor enable bit 6 = 1 drive 2 motor enable bit 5 = 1 drive 1 motor enable bit 4 = 1 drive 0 motor enable bit 3 = 1 diskette DMA enable (reserved PS/2) bit 2 = 1 FDC enable (controller reset) = 0 hold FDC at reset bit 1-0 drive select (0=A 1=B ..) 03F4 r diskette controller status register bit 7 = 1 data register is ready bit 6 = 1 transfer is from controller to system 0 transfer is from system to controller bit 5 = 1 non-DMA mode bit 4 = 1 diskette controller busy bit 3 = 1 drive 3 busy (reserved on PS/2) bit 2 = 1 drive 2 busy (reserved on PS/2) bit 1 = 1 drive 1 busy bit 0 = 1 drive 0 busy 03F5 r diskette command status register 0 bit 7-6 last command status = 00 command terminated successfully = 01 command terminated abnormally = 10 invalid command = 11 terminated abnormally by change in ready signal bit 5 = 1 seek completed bit 4 = 1 equipment check occurred after error bit 3 = 1 not ready bit 2 = 1 head number at interrupt bit 1-0 = 1 unit select (0=A 1=B .. ) (on PS/2 01=A 10=B) status register 1 bit 7 end of cylinder; sector# greater then sectors/track bit 6 = 0 bit 5 = 1 CRC error in ID or data field bit 4 = 1 overrun bit 3 = 0 bit 2 = 1 sector ID not found bit 1 = 1 write protect detected during write bit 0 = 1 ID address mark not found status register 2 bit 7 = 0 bit 6 = 1 deleted Data Eddress Mark detected bit 5 = 1 CRC error in data bit 4 = 1 wrong cylinder detected bit 3 = 1 scan command equal condition satisfied bit 2 = 1 scan command failed, sector not found bit 1 = 1 bad cylinder, ID not found bit 0 = 1 missing Data Address Mark status register 3 bit 7 fault status signal bit 6 write protect status bit 5 ready status bit 4 track zero status bit 3 two sided status signal bit 2 side select (head select) bit 1-0 unit select (0=A 1=B .. ) 03F6 r/w FIXED disk controller data register bit 7-4 reserved bit 3 = 0 reduce write current 1 head select 3 enable bit 2 = 1 disk reset enable 0 disk reset disable bit 1 = 0 disk initialization enable 1 disk initialization disable bit 0 reserved 03F7 r diskette controller DIR (Digital Input Register) bit 7 = 1 diskette change bit 6 FIXED DISK write gate bit 5 FIXED DISK head select 3 / reduced write current bit 4 FIXED DISK head select 2 bit 3 FIXED DISK head select 1 bit 2 FIXED DISK head select 0 bit 1 FIXED DISK drive 1 select bit 0 FIXED DISK drive 0 select conflicts with: bit 0 diskette high density select 03F7 w select register for diskette data transfer rate bit 7-2 reserved bit 1-0 = 00 500 Kb/S mode = 01 300 Kb/S mode = 10 250 Kb/S mode = 11 reserved ------------------------------------------------------------------------------- 03F8-03FF ---- serial port (8250,8251,16450,16550), same as 02E8,02F8 and 03E8 03F8 w serial port, transmitter holding register, which contains the character to be sent. Bit 0 is sent first. bit 7-0 data bits when DLAB=0 (Divisor Latch Access Bit) r receiver buffer register, which contains the received character Bit 0 is received first bit 7-0 data bits when DLAB=0 (Divisor Latch Access Bit) r/w divisor latch low byte when DLAB=1 03F9 r/w divisor latch high byte when DLAB=1 r/w interrupt enable register when DLAB=0 bits 7-4 reserved bit 3 = 1 modem-status interrupt enable bit 2 = 1 receiver-line-status interrupt enable bit 1 = 1 transmitter-holding-register empty interrupt enable bit 0 = 1 received-data-avail.int. enable (and 16550 timeout) - 16550 will interrupt if data exists in the FIFO and isn't read within the time it takes to receive four bytes or if no data is received within the time it takes to receive four bytes 03FA r interrupt identification register. Information about a pending interrupt is stored here. When the ID register is addressed, the highest priority interrupt is held, and no other interrupts are acknowledged until the CPU services that interrupt. bit 7-6 = 00 reserved on 8250, 8251, 16450 = 11 if FIFO queues are enabled (16550 only) bit 5-4 = 0 reserved bit 3 = 0 reserved 8250, 16450 = 1 16550 timeout int. pending bit 2-1 identify pending interrupt with the highest priority = 11 receiver line status interrupt. priority=highest = 10 received data available register interrupt. pr.=second = 01 transmitter holding register empty interrupt. pr.=third = 00 modem status interrupt. priority=fourth bit 0 = 0 interrupt pending. contents of register can be used as a pointer to the appropriate int.service routine 1 no interrupt pending - interrupt pending flag uses reverse logic, 0=pending, 1=none - interrupt will occur if any of the line status bits are set - THRE bit is set when THRE register is emptied into the TSR 03FA w 16650 FCR (FIFO Control Register) bit 7-6 = 00 1 byte = 01 4 bytes = 10 8 bytes = 11 14 bytes bit 5-4 = 00 reserved bit 3 = 1 change RXRDY TXRDY pins from mode 0 to mode 1 bit 2 = 1 clear XMIT FIFO bit 1 = 1 clear RCVR FIFO bit 0 = 1 enable clear XMIT and RCVR FIFO queues - bit 0 must be set in order to write to other FCR bits - bit 1 when set the RCVR FIFO is cleared and this bit is reset the receiver shift register is not cleared - bit 2 when set the XMIT FIFO is cleared and this bit is reset the transmit shift register is not cleared 03FB r/w line control register bit 7 = 1 divisor latch access bit (DLAB) 0 receiver buffer, transmitter holding, or interrupt enable register access bit 6 = 1 set break enable. serial ouput is forced to spacing state and remains there. bit 5 = stick parity bit 4 = 1 even parity select bit 3 = parity enable 1 even number of ones are sent and checked in the data word bits and parity bit 0 odd number of ones are sent and checked bit 2 = 0 one stop bit 1 zero stop bit bit 1-0 00 word length is 5 bits 01 word length is 6 bits 10 word length is 7 bits 11 word length is 8 bits 03FC r/w modem control register bit 7-5 = 0 reserved bit 4 = 1 loopback mode for diagnostic testing of serial port output of transmitter shift register is looped back to receiver shift register input. In this mode transmitted data is received immediately so that the CPU can verify the transmit data/receive data serial port paths. bit 3 = 1 auxiliary user-designated output 2 bit 2 = 1 auxiliary user-designated output 1 bit 1 = 1 force request-to-send active bit 0 = 1 force data-terminal-ready active 03FD r line status register bit 7 = 0 reserved bit 6 = 1 transmitter shift and holding registers empty bit 5 = 1 transmitter holding register empty. Controller is ready toaccept a new character to send. bit 4 = 1 break interrupt. the received data input is held in in the zero bit state longer than the time of start bit + data bits + parity bit + stop bits. bit 3 = 1 framing error. the stop bit that follows the last parity or data bit is a zero bit. bit 2 = 1 parity error. Character has wrong parity bit 1 = 1 overrun error. a character was sent to the receiver buffer before the previous character in the buffer could be read. This destroys the previous character. bit 0 = 1 data ready. a complete incoming character has been received and sent to the receiver buffer register. 03FE r modem status register bit 7 = 1 data carrier detect bit 6 = 1 ring indicator bit 5 = 1 data set ready bit 4 = 1 clear to send bit 3 = 1 delta data carrier detect bit 2 = 1 trailing edge ring indicator bit 1 = 1 delta data set ready bit 0 = 1 delta clear to send - bits 0-3 are reset when the CPU reads the MSR - bit 4 is the Modem Control Register RTS during loopback test - bit 5 is the Modem Control Register DTR during loopback test - bit 6 is the Modem Control Register OUT1 during loopback test - bit 7 is the Modem Control Register OUT2 during loopback test 03FF r/w scratch register ------------------------------------------------------------------------------- Adresses above 03FF apply to EISA machines only ! 1000-1FFF slot 1 EISA 2000-2FFF slot 2 EISA 3000-3FFF slot 3 EISA 4000-4FFF slot 4 EISA 5000-5FFF slot 5 EISA 6000-6FFF slot 6 EISA 7000-7FFF slot 7 EISA ------------------------------------------------------------------------------- 0401-04D6 ---- used by EISA systems only 0401 r/w DMA channel 0 word count byte 2 (high) 0403 r/w DMA channel 1 word count byte 2 (high) 0405 r/w DMA channel 2 word count byte 2 (high) 0407 r/w DMA channel 3 word count byte 2 (high) 040A w extended DMA chaining mode register, channels 0-3 bit 7-5 reserved bit 4 = 0 generates IRQ13 = 1 generates terminal count bit 3 = 0 do not start chaining = 1 programming complete bit 2 = 0 disable buffer chaining mode (default) = 1 enable buffer chaining mode bit 1-0 DMA channel select 040A r channel interrupt (IRQ13) status register bit 7-5 interrupt on channels 7-5 bit 4 reserved bit 3-0 interrupt on channels 3-0 040B w DMA extended mode register for channels 3-0. bit settings same as 04D6 bit 7 = 0 enable stop register bit 6 = 0 terminal count is an output for this channel (default) bit 5-4 DMA cycle timing = 00 ISA-compatible (default) = 01 type A timing mode = 10 type B timing mode = 11 burst DMA mode bit 3-2 Address mode = 00 8-bit I/O, count by bytes (default) = 01 16-bit I/O, count by words, address shifted = 10 32-bit I/O, count by bytes = 11 16-bit I/O, count by bytes bit 1-0 DMA channel select ------------------------------------------------------------------------------- 0461 r/w Extended NMI status/control register bit 7 = 1 NMI pending from fail-safe timer (read only) bit 6 = 1 NMI pending from bus timeout NMI status (read only) bit 5 = 1 NMI pending (read only) bit 4 reserved bit 3 = 1 bus timeout NMI enable (read/write) bit 2 = 1 fail-safe NMI enable (read/write) bit 1 = 1 NMI I/O port enable (read/write) bit 0 RSTDRV. bus reset (read/write) = 0 normal bus reset operation = 1 reset bus asserted 0462 w Software NMI register. writing to this register causes an NMI if NMI's are enabled bit 7 = 1 generates an NMI 0464 r bus master status latch register (slots 1-8). identifies the last bus master that had control of the bus bit 7 = 0 slot 8 had control last bit 6 = 0 slot 7 had control last bit 5 = 0 slot 6 had control last bit 4 = 0 slot 5 had control last bit 3 = 0 slot 4 had control last bit 2 = 0 slot 3 had control last bit 1 = 0 slot 2 had control last bit 0 = 0 slot 1 had control last 0465 r bus master status latch register (slots 9-16) bit 7 = 0 slot 16 had control last bit 6 = 0 slot 15 had control last bit 5 = 0 slot 14 had control last bit 4 = 0 slot 13 had control last bit 3 = 0 slot 12 had control last bit 2 = 0 slot 11 had control last bit 1 = 0 slot 10 had control last bit 0 = 0 slot 9 had control last ------------------------------------------------------------------------------- 0481-048B ---- EISA DMA page registers 0481 r/w DMA channel 2 address byte 3 (high) 0482 r/w DMA channel 3 address byte 3 (high) 0483 r/w DMA channel 1 address byte 3 (high) 0487 r/w DMA channel 0 address byte 3 (high) 0489 r/w DMA channel 6 address byte 3 (high) 048A r/w DMA channel 7 address byte 3 (high) 048B r/w DMA channel 5 address byte 3 (high) ------------------------------------------------------------------------------- 04C6-04CF ---- EISA DMA count registers 04C6 r/w DMA channel 5 word count byte 2 (high) 04CA r/w DMA channel 6 word count byte 2 (high) 04CE r/w DMA channel 7 word count byte 2 (high) ------------------------------------------------------------------------------- 04D0-04D1 ---- EISA IRQ control 04D0 w IRQ 0-7 interrupt edge/level registers bit 7 = 1 IRQ 7 is level sensitive bit 6 = 1 IRQ 6 is level sensitive bit 5 = 1 IRQ 5 is level sensitive bit 4 = 1 IRQ 4 is level sensitive bit 3 = 1 IRQ 3 is level sensitive bit 2-0 reserved 04D1 w IRQ 8-15 interrupt edge/level registers bit 7 = 1 IRQ 15 is level sensitive bit 6 = 1 IRQ 14 is level sensitive bit 5 = 1 reserved bit 4 = 1 IRQ 12 is level sensitive bit 3 = 1 IRQ 11 is level sensitive bit 2 = 1 IRQ 10 is level sensitive bit 1 = 1 IRQ 9 is level sensitive bit 0 reserved ------------------------------------------------------------------------------- 04D4-04D6 ---- EISA DMA control 04D4 r DMA chaining status 04D4 w extended DMA chaining mode register, channels 4-7 bit 7-5 = 0 reserved bit 4 = 0 generates IRQ 13 = 1 generates terminal count bit 3 = 0 do not start chaining = 1 programming complete bit 2 = 0 disable buffer chaining mode (default) = 1 enable buffer chaining mode bit 1-0 DMA channel select 04D6 w DMA extended mode register for channels 4-7 bit settings same as 04B bit 7 = 0 enable stop register bit 6 = 0 terminal count is an output for this channel (default) bit 5-4 DMA cycle timing = 00 ISA-compatible (default) = 01 type A timing mode = 10 type B timing mode = 11 burst DMA mode bit 3-2 Address mode = 00 8-bit I/O, count by bytes (default) = 01 16-bit I/O, count by words, address shifted = 10 32-bit I/O, count by bytes = 11 16-bit I/O, count by bytes bit 1-0 DMA channel select ------------------------------------------------------------------------------- 04E0-04FF ---- EISA DMA stop registers 04E0-04E2 r/w channel 0 04E4-04E6 r/w channel 1 04E8-04EA r/w channel 2 04EC-04EE r/w channel 3 04F4-04F6 r/w channel 5 04F8-04FA r/w channel 6 04FC-04FE r/w channel 7 ------------------------------------------------------------------------------- 0601 w System control. Laptop chipset: Headland HL21 & Acer M5105 bit 7 = 1 power led on bit 6 = 1 LCD backlight off bit 5 bit 4 bit 3 bit 2 = 1 video chips disabled, screen blanked. bit 1 bit 0 = 1 will lock up your machine! r bit 7 = 0 if screen enabled always these values bit 6 = 0 bit 5 = 0 bit 4 = 0 bit 3 = 0 bit 2 = 1 bit 1 = 0 bit 0 = 0 ------------------------------------------------------------------------------- 0620-0627 ---- PC network (adapter 1) 0628-062F ---- PC network (adapter 2) ------------------------------------------------------------------------------- 0680 ---- Microchannel POST Diagnostic (write only) ------------------------------------------------------------------------------- 06E2-06E3 ---- data aquisition (adapter 1) ------------------------------------------------------------------------------- 0790-0793 ---- cluster (adapter 1) ------------------------------------------------------------------------------- 0800-08FF ---- I/O port access registers for extended CMOS RAM or SRAM (256 bytes at a time) Sometimes plain text can be seen here. ------------------------------------------------------------------------------- 0800-08FF ---- reserved for EISA system motherboard ------------------------------------------------------------------------------- 0A20-0A23 ---- Token Ring (adapter 1) 0A24-0A27 ---- Token Ring (adapter 2) ------------------------------------------------------------------------------- 0AE2-0AE3 ---- cluster (adapter 2) 0B90-0B93 ---- cluster (adapter 2) ------------------------------------------------------------------------------- 0C00 r/w page register to write to SRAM or I/O ------------------------------------------------------------------------------- 0C00-0CFF ---- reserved for EISA system motherboard ------------------------------------------------------------------------------- 0C7C bit 7-4 (Compaq) ------------------------------------------------------------------------------- 0C80-0C83 ---- EISA system board ID registers ------------------------------------------------------------------------------- 1000-10FF ---- available for EISA slot 1 ------------------------------------------------------------------------------- 1390-1393 ---- cluster (adapter 3) ------------------------------------------------------------------------------- 1400-14FF ---- available for EISA slot 1 ------------------------------------------------------------------------------- 1800-18FF ---- available for EISA slot 1 ------------------------------------------------------------------------------- 1C00-1CFF ---- available for EISA slot 1 ------------------------------------------------------------------------------- 1C80-1C8F ---- VESA XGA Video in EISA slot 1 1C80-1C83 r/w EISA Video ID 1C84 r/w EISA Video expansion board control 1C85 r/w EISA Setup control 1C88 r/w EISA Video Programmable Option Select 0 1C89-1C8F r/w EISA Video Programmable Option Select 1-7 ------------------------------------------------------------------------------- 2000-20FF ---- available for EISA slot 2 ------------------------------------------------------------------------------- 2100-210F ---- IBM XGA (eXtended Graphics Adapter 8514/A) (first installed) 2110-211F ---- IBM XGA (eXtended Graphics Adapter 8514/A) (second installed) 2120-212F ---- IBM XGA (eXtended Graphics Adapter 8514/A) (third installed) 2130-213F ---- IBM XGA (eXtended Graphics Adapter 8514/A) (fourth installed) 2140-214F ---- IBM XGA (eXtended Graphics Adapter 8514/A) (fifth installed) 2150-215F ---- IBM XGA (eXtended Graphics Adapter 8514/A) (sixth installed) 2160-216F ---- IBM XGA (eXtended Graphics Adapter 8514/A) (seventh installed) 2170-217F ---- IBM XGA (eXtended Graphics Adapter 8514/A) (eighth installed) ------------------------------------------------------------------------------- 2100 ---- XGA Video Operating Mode Register Note: this port is for the first XGA in the system; 2110-2170 are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2101 ---- XGA VIdeo Aperture Control Note: this port is for the first XGA in the system; 2111-2171 are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2102-2103 ---- XGA ??? Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2104 ---- XGA Video Interrupt Enable Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2105 ---- XGA Video Interrupt Status Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2106 ---- XGA Video Virtual Memory Control Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2107 ---- XGA Video Virtual Memory Interrupt Status Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2108 ---- XGA Video Aperture Index Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2109 ---- XGA Video Memory Access Mode Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 210A ---- XGA Video Index for Data Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 210B ---- XGA Video Data (byte) Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 210C-210F ---- XGA Video Data (word/dword) Note: this port is for the first XGA in the system; 211x-217x are used for the second through eighth XGAs ------------------------------------------------------------------------------- 2110-217F ---- secondary XGA adapters (see individual entries above) ------------------------------------------------------------------------------- 2390-2393 ---- cluster (adapter 4) ------------------------------------------------------------------------------- 2400-24FF ---- available for EISA slot 2 ------------------------------------------------------------------------------- 27C6 r/w LCD timeout in minutes (Compaq LTE Lite) ------------------------------------------------------------------------------- 2800-28FF ---- available for EISA slot 2 ------------------------------------------------------------------------------- 2C80-2C8F ---- VESA XGA Video in EISA slot 2 (see 1C80-1C8F) ------------------------------------------------------------------------------- 3000-30FF ---- available for EISA slot 3 ------------------------------------------------------------------------------- 3220-3227 ---- serial port 3, description same as 03F8 (MCA) 3228-322F ---- serial port 4, description same as 03F8 (MCA) ------------------------------------------------------------------------------- 3400-34FF ---- available for EISA slot 3 ------------------------------------------------------------------------------- 3540-354F ---- IBM SCSI (Small Computer System Interface) adapter 3550-355F ---- IBM SCSI (Small Computer System Interface) adapter 3560-356F ---- IBM SCSI (Small Computer System Interface) adapter 3570-357F ---- IBM SCSI (Small Computer System Interface) adapter ------------------------------------------------------------------------------- 3800-38FF ---- available for EISA slot 3 ------------------------------------------------------------------------------- 3C00-3CFF ---- available for EISA slot 3 ------------------------------------------------------------------------------- 3C80-3C8F ---- VESA XGA Video in EISA slot 3 3C80-3C83 r/w EISA Video ID 3C84 r/w EISA Video expansion board control 3C85 r/w EISA Setup control 3C88 r/w EISA Video Programmable Option Select 0 3C89-3C8F r/w EISA Video Programmable Option Select 1-7 SeeAlso: 1C80-1C8F,2C80-2C8F,7C80-7C8F ------------------------------------------------------------------------------- 4000-40FF ---- available for EISA slot 4 ------------------------------------------------------------------------------- 4220-4227 ---- serial port, description same as 03F8 4228-422F ---- serial port, description same as 03F8 ------------------------------------------------------------------------------- 42E0-42EF ---- GPIB (General Purpose Interface Bus, IEEE 488 interface) 42E1 r/w GPIB (adapter 2) ------------------------------------------------------------------------------- 4400-44FF ---- available for EISA slot 4 ------------------------------------------------------------------------------- 46E8 ---- VGA video adapter enable 46E8 r/w enable flags bits 7-5 unused or vendor-specific bit 4: setup for POS registers (MCA) bit 3: enable video I/O ports and video buffer bits 2-0 unused or vendor-specific Note: IBM uses this port for adapter-card VGAs only, and port 03C3 for motherboard VGA only SeeAlso: 03C3 ------------------------------------------------------------------------------- 4800-48FF ---- available for EISA slot 4 ------------------------------------------------------------------------------- 4C00-4CFF ---- available for EISA slot 4 ------------------------------------------------------------------------------- 4C80-4C8F ---- VESA XGA Video in EISA slot 4 (see 3C80-3C8F) SeeAlso: 1C80-1C8F,6C80-6C8F ------------------------------------------------------------------------------- 5000-50FF ---- available for EISA slot 5 ------------------------------------------------------------------------------- 5220-5227 ---- serial port, description same as 03F8 5228-522F ---- serial port, description same as 03F8 ------------------------------------------------------------------------------- 5400-54FF ---- available for EISA slot 5 ------------------------------------------------------------------------------- 5800-58FF ---- available for EISA slot 5 ------------------------------------------------------------------------------- 5C00-5CFF ---- available for EISA slot 5 ------------------------------------------------------------------------------- 5C80-5C8F ---- VESA XGA Video in EISA slot 5 5C80-5C83 r/w EISA Video ID 5C84 r/w EISA Video expansion board control 5C85 r/w EISA Setup control 5C88 r/w EISA Video Programmable Option Select 0 5C89-5C8F r/w EISA Video Programmable Option Select 1-7 SeeAlso: 2C80-2C8F,4C80-4C8F,6C80-6C8F ------------------------------------------------------------------------------- 6000-60FF ---- available for EISA slot 6 ------------------------------------------------------------------------------- 62E0-62EF ---- GPIB (General Purpose Interface Bus, IEEE 488 interface) 62E1 r/w GPIB (adapter 3) ------------------------------------------------------------------------------- 6400-64FF ---- available for EISA slot 6 ------------------------------------------------------------------------------- 6800-68FF ---- available for EISA slot 6 ------------------------------------------------------------------------------- 6C00-6CFF ---- available for EISA slot 6 ------------------------------------------------------------------------------- 6C80-6C8F ---- VESA XGA Video in EISA slot 1 6C80-6C83 r/w EISA Video ID 6C84 r/w EISA Video expansion board control 6C85 r/w EISA Setup control 6C88 r/w EISA Video Programmable Option Select 0 6C89-1C8F r/w EISA Video Programmable Option Select 1-7 SeeAlso: 1C80-1C8F,2C80-2C8F,5C80-5C8F ------------------------------------------------------------------------------- 7000-70FF ---- available for EISA slot 7 ------------------------------------------------------------------------------- 7400-74FF ---- available for EISA slot 7 ------------------------------------------------------------------------------- 7800-78FF ---- available for EISA slot 7 ------------------------------------------------------------------------------- 7C00-7CFF ---- available for EISA slot 7 ------------------------------------------------------------------------------- 7C80-7C8F ---- VESA XGA Video in EISA slot 7 7C80-7C83 r/w EISA Video ID 7C84 r/w EISA Video expansion board control 7C85 r/w EISA Setup control 7C88 r/w EISA Video Programmable Option Select 0 7C89-7C8F r/w EISA Video Programmable Option Select 1-7 SeeAlso: 1C80-1C8F, 6C80-6C8F ------------------------------------------------------------------------------- 8000-80FF ---- available for EISA slot 8 ------------------------------------------------------------------------------- 82E0-82EF ---- GPIB (General Purpose Interface Bus, IEEE 488 interface) 82E1 r/w GPIB (adapter 4) ------------------------------------------------------------------------------- 82F8-82FF ---- serial port, description same as 03F8 83F8-83FF ---- serial port, description same as 03F8 ------------------------------------------------------------------------------- 8400-84FF ---- available for EISA slot 8 ------------------------------------------------------------------------------- 8800-88FF ---- available for EISA slot 8 ------------------------------------------------------------------------------- 8C00-8CFF ---- available for EISA slot 8 ------------------------------------------------------------------------------- 9000-90FF ---- available for EISA slot 9 ------------------------------------------------------------------------------- 9400-94FF ---- available for EISA slot 9 ------------------------------------------------------------------------------- 9800-98FF ---- available for EISA slot 9 ------------------------------------------------------------------------------- 9C00-9CFF ---- available for EISA slot 9 ------------------------------------------------------------------------------- A220 ???? soundblaster support in AMI Hi-Flex BIOS ???? ------------------------------------------------------------------------------- A2E0-A2EF ---- GPIB (General Purpose Interface Bus, IEEE 488 interface) A2E1 r/w GPIB (adapter 5) ------------------------------------------------------------------------------- AFFF r/w plane 0-3 system latch (video register) ------------------------------------------------------------------------------- B220-B227 ---- serial port, description same as 03F8 B228-B22F ---- serial port, description same as 03F8 ------------------------------------------------------------------------------- C220-C227 ---- serial port, description same as 03F8 C228-C22F ---- serial port, description same as 03F8 ------------------------------------------------------------------------------- D220-D227 ---- serial port, description same as 03F8 D228-D22F ---- serial port, description same as 03F8 ------------------------------------------------------------------------------- C2E0-C2EF ---- GPIB (General Purpose Interface Bus, IEEE 488 interface) C2E1 r/w GPIB (adapter 6) ------------------------------------------------------------------------------- E2E0-E2EF ---- GPIB (General Purpose Interface Bus, IEEE 488 interface) E2E1 r/w GPIB (adapter 7) ------------------------------------------------------------------------------- MEMORY-MAPPED ADDRESSES ------------------------------------------------------------------------------- 80C00000 Compaq Deskpro 386 system memory board register 80C00000 w RAM relocation register bit 7-2 Reserved, always write 1's. bit 1 = 0 Write-protect 128-Kbyte RAM at FE0000. = 1 Do not write-protect RAM at FE0000. bit 0 = 0 Relocate 128-Kbyte block at FE0000 to address 0E0000 = 1 128-Kbyte RAM is addressed only at FE0000. 80C00000 r Diagnostics register bit 7 = 0 memory expansion board is installed bit 6 = 0 second 1 MB of system memory board is installed bit 5-4 = 00 base memory set to 640 KB 01 invalid 10 base memory set to 512 KB 11 base memory set to 256 KB bit 3 = 0 parity error in byte 3 bit 2 = 0 parity error in byte 2 bit 1 = 0 parity error in byte 1 bit 0 = 0 parity error in byte 0 (in 32-bit double word) ------------------------------------------------------------------------------- C0000000-C000FFFF Weitek "Abacus" math coprocessor ------------------------------------------------------------------------------- -------------CREDITS------------------------- Chuck Proctor <71534.2302@CompuServe.COM> [Some of the information in this list was extracted from Frank van Gilluwe's _The_Undocumented_PC_, a must-have book for anyone programming down to the "bare metal" of a PC.] [Some of the information in this list from the shareware version of Dave Williams' DOSREF, v3.0]