 |
|
|
|
|
Diagnostic Tool
| Software Name |
Discription |
Diagnostic Tool Ver. 6
(For EIDE Hard Disk Drives)
 fjdt_6.exe (196 KB) |
This
diagnostic tool is available for use by customers who feel their
Fujitsu drive may not be functioning as well as it should be. It is
only designed for use on all Fujitsu EIDE hard drives.
There are 2 test modes:
- Quick Test
About 1 minute, does random seek/read tests.
- Comprehensive Test
About 6 minutes, also performs surface scan.
* Runs only under DOS from a bootdisk. |
Diagnostic Tool Ver.1.4
(For SCSI Hard Disk Drives)
sdiag_14.exe (617 KB) |
This
diagnostic tool is available for use by customers who feel their
Fujitsu drive may not be functioning as well as it should be. It is
only designed for use on all Fujitsu SCSI hard drives.
There are 3 test modes:
- Quick Test
1 to 3 minutes, a basic operational test.
- Standard Test
20 to 25 minutes, also performs Read/Write test.
- Extended Test
30 to 70 minutes, also verify and surface test.
*Supports Windows NT/9x/2000 or later
*Requires Adaptec's ASPI32 files. |
|
|
UDMA Utility
| Software Name |
Discription |
UDMA Utility
(For MPD, MPE, and MPF Series Hard Disk Drives)
ata24.zip (8 KB) |
The
UDMA utility is designed to change the status of the Fujitsu's MPD,
MPE, and MPF series hard disk drives to pre-set transfer rates for
compatible operation. Some motherboards can not run the drive properly
at the detected rate of transfer. Users who experience UDMA replies of
intermittently failing upon starting the Operating System should run
either of the UDMA utilities |
UDMA Utility
(For MPG Series Hard Disk Drives)
ata245.zip (8 KB) |
The
UDMA utility is designed to change the status of the Fujitsu's MPG
series hard disk drives to pre-set transfer rates for compatible
operation. Some motherboards can not run the drive properly at the
detected rate of transfer. Users who experience UDMA replies of
intermittently failing upon starting the Operating System should run
either of the UDMA utilities |
|
|
Flash Utility
| Software Name |
Discription |
Fujitsu HDD Flash Utility
(For MPG3xxxAT Models)
gen_upgrade101.exe (1.8 MB) |
A
utility to upgrade model MPG3102AT and MPG3204AT 5400 RPM ATA hard disk
drivers only. This utility checks your system for applicable drives and
will automatically update the firmware with a new version that can
offer improved reliability in some systems. INSTRUCTIONS FOR USE:
Download the "Fujitsu HDD
Flash" utility below to your Hard Disk Drive. When download is
complete, execute and follow the on-screen instructions to create a
floppy disk based firmware upgrade utility (1.44MB Floppy Diskette
Required).
|
|
|
Change Definition Utility
| Software Name |
Discription |
Change Definition Utility
chgdef2.zip (137 KB) |
<The
Change Definition utility is designed to alter certain drive parameters
(including Unit Attention, Bus Parity, and SCSI level) for the Fujitsu
M16xx and M2915 family of drives. This is only for the SCSI interface
of these drives. The files available here are in Pkzip format. The
files should be unZIPed before installation is attempted. |
|
|
Erase Utility
| Software Name |
Discription |
Fujitsu Erase Utility
clean.zip (31 KB) |
Note: This program works only with any FUJITSU IDE hard disk drives
This
procedure performs a pseudo-formatting to the drive. It erases all of
your previous data and reinitializes it to "00" pattern. By performing
this task, you will be able to erase the whole user area including your
Master Boot Record, Partition Table, FAT (File Allocation Table), and
all the files and data it refers to. Use this program if you want to be
sure your drive is clean.
Warning:
All the previous data will be lost when performing the 'Erase' task.
Please backup all your important files and data before running this program. |
|
|
Disk Manager® "Disk Go!"
| Software Name |
Discription |
Ontrack® Disk Manager® "Disk Go!"
Download from Ontrack web site |
Note: You do not need "Disk Go!" if your BIOS recognizes the full drive capacity
Disk Manager®
"Disk Go!" is a dynamic drive overlay that allows you to override the
drive settings from your BIOS setup. "Disk Go!" is made by Ontrack
Computer, Inc. for Fujitsu hard disk drive products. It is available
from their website which will work with Fujitsu hard disk drives only.
Please take the following steps:
- Make sure the controller or BIOS has LBA mode enabled to gain the full capacity of the drive.
- If you do not have either an EIDE controller or LBA mode support, leave it at the detected settings and run "Disk Go!" overlay.
|
|
|
If
you are unable to find the information you want here, please call (800)
626-4686, option 2 for assistance between the hours of 5:00 a.m. - 7:00
p.m. PST Monday through Friday.
All brand names and
product names are trademarks or registered trademarks of their
respective owners. Specifications are subject to change without notice. |
 |
White Paper (6 KB)