                                SETUP


   NOTE: The first two selections are available only on an AT type
   computer with CMOS memory.
   
   DATE / TIME
   From this selection, you may set the date and time used by the CMOS
   Clock/Calendar.  Press F2 to select Time, F3 to select Date.  The
   Right and Left Arrow keys are used to select the field (hour,
   minute, second for time; month, day, year for date).  Type in the
   correct values and press the Enter key to change the values.  If you
   wish to leave the values unchanged, type Esc instead of Enter when
   in one of the fields.  After you have changed the date and time to
   correct values, press Esc to return to the menu.
   
   CMOS EDIT
   CMOS Edit permits you to change the information stored that is used
   to  determine your hardware configuration when the computer is
   booted.  A  menu of selections is presented.
   
   DATE/TIME
   This selection is the same as Date/Time from the Setup menu.
   
   HARD DISK (C or D):
   These two selections allow you to specify what type of disk(s) are
   attached to your computer.  Each refers to a physical hard disk.  If
   you only have one actual disk drive that is partitioned into more
   than one logical drive, use the setup only for hard drive C.  See
   Appendix D of the user's guide to help determine what type your disk
   is.  If you are using a hard disk driver, such as SpeedStor or
   DMDrvr,  the actual disk configuration may be determined from the
   driver at boot time rather than from the table.  In that event, see
   the documentation from the hard disk manufacturer to determine which
   drive type you should use.
   
   FLOPPY DISK (A or B):
   This permits you to specify which floppy disk drives are attached to
   your computer.  The choices are 5-1/4" floppy disk drives, 360K or
   1.2M, and 3-1/2" floppy disk drives, 720K or 1.44M.

   BASE MEMORY
   After selecting this item, type in the amount of base memory (up to
   640K) your computer has.  If your computer is an 80286 or 80386 and
   you have more than 640K, specify the remainder as Extended memory.
   E.g. if you have 1 megabyte of memory (1024K), specify 640K as base
   memory and 384K as extended memory.

   EXTENDED MEMORY
   If your computer is an 80286 or 80386, specify the amount of memory
   in excess of 640K your computer has.  See base memory above for an
   example.

   VIDEO SELECTION
   This will determine the default display characteristics when your
   computer is booted.  As appropriate, select Monochrome (MDA or MGA
   adapter), Color 80 or Color 40 (CGA), or EGA/VGA.

   ERROR HALT
   This determines the action taken by your computer when it discovers
   an error during booting.  The normal selection is Halt on All
   Errors, which will cause a message to be displayed and request an
   action from you (normally press F1 to continue) during the boot
   process if any error is detected.
   
   DONE, EXIT & REBOOT
   After you have completed editing the CMOS setup, select this menu
   item and you will be presented with a choice of Quit or Update.  If
   you do not wish to put your new changes in effect, choose Quit.  If
   you do wish to update the CMOS setup, press Update.  Your computer
   will then reboot to place the CMOS changes into effect.

   SOUND CHANGE
   Select Sound On (beeps on error) or Sound Off.

   COLOR CHANGE
   Select Color On or Color Off (Monochrome).

   MONITOR CHANGE
   If you have more than one monitor attached, you may select either
   one from this menu.  If you have only one monitor,  you will receive
   a message to that effect as no selection is possible.

   FILES EDITOR
   This feature enables you to edit the CONFIG.SYS or AUTOEXEC.BAT file
   on either Drive A: or Drive C: (the common DOS boot disks.) The editor
   starts in Overwrite mode. The following Function key features are
   available:

	F2 - Search Mode
	F3 - Find Next (in Search Mode)
	F4 - Mark Start of Text Block (for edit/move/copy/delete)
	F5 - Mark End of Text Block
	F6 - Tag Block: Tag Text Block that cursor is in for a Move,
		Copy or Delete of Block. Move cursor to new location 
		for Block Move, press again to move block.
	F7 - Copy Text Block tagged by F6 to new location of cursor.
	F8 - Delete Text Block tagged by F6.
	F10 - Save changes to file and Exit to QAPlus menu.

                               *** END ***
