ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º README for º º º º UM8673/UM8886A PCI BUS IDE DEVICE DRIVERS º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ (1). UM8673/UM8886A PCI BUS IDE DEVICE DRIVERS are saved in this diskette. These drivers are not only designed for UM8673/UM8886A to improve IDE I/O data transfer rate between IDE hard disk(s) and your system, but also support up to 4 hard drives. The following files are included : 1. README 2. INSTALL4.EXE ( V2.1, auto install utility ) 3. UM8673.SYS ( V2.1, DOS device driver ) 4. UM8673.386 ( V2.1, Windows device driver for V3.1x ) 5. INT13.386 ( V2.1, Windows device driver for V3.1x ) 6. UMC1S506.ADD ( V2.1, OS/2 device driver for V2.x, 3.0 ) 7. UMC310.DSK ( V2.1, NetWare device driver for V3.10 ) 8. UMC311.DSK ( V2.1, NetWare device driver for V3.11, 3.12 ) 9. UMC401.DSK ( V2.1, NetWare device driver for V4.0x ) 10. ATDISK.SYS ( V2.0, Windows NT device driver for V3.x ) 11. INSTALL.EXE ( Install Utility for Windows NT ) 12. RESTORE.EXE ( Restore Utility for Windows NT ) 13. UNIX.UMC ( V2.0, SCO UNIX device drive for 3.2V4.1 ) 14. RELEASE.TXT ( Release Note for Diskette V2.1 ) (2). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install Utility for UM8673/UM8886A PCI-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The INSTALL4.EXE utility can detect the speeds of the hard disks which are attached on the controller automatically and it also can install drivers for you. Please follow the steps below to excute this program first. I. Insert this diskette in a floppy disk drive, and close the drive door. II. At the command prompt, type the drive letter of the drive you are using, followed by a colon(:), and then press ENTER. III. Type INSTALL4, and then press ENTER. IV. Follow the instructions on the screen to detect hard disk(s) speed and install driver(s). This program may get an incorrect speed in some few cases. At that time, please install the drivers manually to reduce the drive speed step by step until the system boots or becomes stable. Please remember the current speed and minus 2 if the FIFO is enabled, or minus 4 if FIFO is disabled. At this way, it will work out the optimized performance of your system. If it is possible, please burn-in your system with IDE operations to make sure the stability of your system. (3). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install DOS Device Driver for PCI-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The INSTALL4.EXE utility can install DOS device driver automatically. If you want to install DOS device driver manually or change the drive speed, please follow the steps below. I. Copy the DOS\UM8673.SYS into the appropriate path. II. Add following statement to your CONFIG.SYS file to auto load the driver during bootup. Device=[drive:][\path\]UM8673.SYS[/D][/F][/NF][/Cyl][/Hd][/Sec][/SIRQ:] where D Drive n speed m(0-17) ( 0 the lowest ) Cyl Drive n(2-3) cylinder number m Hd Drive n(2-3) head number m Sec Drive n(2-3) sector number m F Enable FIFO for drive n NF Disable FIFO for drive n SIRQ: Secondary channel IRQ (10 or 12 or 15) For instance, the user wants to load UM8673.SYS with drive 0 speed = 6 and FIFO enabled. The DOS driver resides in the root directory of the drive C:. Add the following statement to your CONFIG.SYS file. DEVICE = C:\UM8673.SYS /D0:6 /F0 You don't need to specify drive speed parameters usually, because the device driver is reconfigured for the optimal speed setting. III. Reboot your system. (4). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install Windows Device Driver V3.x for PCI-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The INSTALL4.EXE utility can install Windows device driver automatically. If you want to install Windows device driver for your system manually or change the drive speed, please follow the steps below. I. Copy the Windows\UM8673.386 and Windows\INT13.386 into the appropriate path. II. Check if the following lines exist in the [386Enh] section of your SYSTEM.INI file. [386Enh] 32BitDiskAccess=ON device=*int13 device=*wdctrl If any statement does not exist, please add it to the [386Enh] section. Please add a preceding semi-colon in front of "device=*wdctrl" and "device=*int13" command lines. If "32BitDiskAccess" option is set to be "OFF", Please change it to be "ON". III. Add these following statements to the [386Enh] section in your \WINDOWS\SYSTEM.INI file. Device = [drive:][\path\] UM8673.386 device = [drive:][\path\] INT13.386 DriveSpeed = [/D][/F][/NF] where D Drive n speed m(0-17) ( 0 the lowest ) F Enable FIFO for drive n NF Disable FIFO for drive n For instance, the user wants to load Windows drivers with drive 1 speed = 11 and FIFO disabled. The Windows drivers reside in the WINDOWS\SYSTEM directory of the drive C:. Add the following statements to your SYSTEM.INI file. [386Enh] 32BitDiskAccess=ON ;device=*int13 ;device=*wdctrl DriveSpeed = /D1:11 /NF1 device = c:\windows\system\UM8673.386 device = c:\windows\system\INT13.386 You don't need to specify drive speed parameters usually, because the device driver is reconfigured for the optimal speed setting. IV. Reenter your Windows. (5). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install OS/2 Device Driver V2.x/V3.0 for PCI-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ If you want to install OS/2 device driver for your system, please follow the steps below. I. Copy the OS2\UMC1S506.ADD into the OS2 directory of your system for OS/2 V2.x or copy the OS2\UMC1S506.ADD into the OS2\BOOT sub- directory of your system for OS/2 V3.0. II. Check if the following line exists in the CONFIG.SYS file. BaseDev = IBM1S506.ADD If the statement exists, please delete it or add "REM" in front of it. III. Add this following statement to your CONFIG.SYS file. BaseDev = UMC1S506.ADD [/A:<0 or 1> /IRQ: /U:<0 or 1> /S: /F /NF] where speed : drive speed setting from 0 to 17 ( 0 the lowest ) F : enable FIFO for drive NF : disable FIFO for drive irq : 10 or 12 or 15 Note : The user MUST NOT specify either drive or path name. For instance, the user wants to load UMC1S506.ADD with drive (Unit) 0 speed 6 (FIFO disabled) and drive (Unit) 1 speed 11 (FIFO enabled) which are attached on Adapter 0. Add the following statement to your CONFIG.SYS file. BaseDev = UMC1S506.ADD /A:0 /U:0 /S:6 /NF /U:1 /S:11 /F You don't need to specify drive speed parameters usually, because the device driver is reconfigured for the optimal speed setting. IV. Reboot your system. (6). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install NetWare Device Driver for PCI-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ If you want to install NetWare device driver for your system, please follow the steps below. I. Copy the NetWare\UMCxxx.DSK into the appropriate path. II. Bring up the NetWare server of your system. III. Type the following statement after the ":" prompt :load UMCxxx PORT= INT= [/D] [/F] [/NF] where x 1F0 or 170 y E or F D Drive n speed m(0-11) ( 0 the lowest ) F Enable FIFO for drive n NF Disable FIFO for drive n Note : You MUST NOT load the ISADISK.DSK when you are installing UMCxxx.DSK Netware driver. For instance, the user wants to load UMC310.DSK with drive 0 speed 6 and drive 1 speed 11 which are attached on the primary controller. Add the following statement after the ":" prompt. :LOAD UMC310 /D0:6 /D1:11 PORT=1F0 INT=E You don't need to specify drive speed and Cylinder, Head, Sector parameters usually, because the device driver is reconfigured for the optimal speed setting and detect the Cylinder, Head, Sector automatically. (7). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install Windows NT Device Driver for PCI-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ I. Insert this diskette in a floppy disk drive, and close the drive door. II. At the DOS command prompt, type the drive letter of the floppy disk drive you are using, followed by a colon(:), type INSTALL, and then press ENTER. For example, C:\WINNT>a:\winnt\install III. The Installation Utility will install the Windows NT Device Driver automatically. ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Restore Windows NT Device Driver for VL-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ I. At the DOS command prompt, type the drive letter of the floppy disk drive you are using, followed by a colon(:), type RESTORE, and then press ENTER. For example, C:\WINNT>a:\winnt\restore II. The Restore Utility will restore the Windows NT Device Driver automatically. (8). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install SCO UNIX Device Driver for PCI-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ If you want to install SCO UNIX device driver for your system, please follow the steps below. Type the following statements under UNIX system. I. Mkdir /UM8673.bin II. Cd /UM8673.bin III. Doscp a:unix.umc . IV. Tar xf - < unix.umc V. Cd /UM8673.bin VI. ./istl.UM8673 If you want to remove SCO UNIX device driver from your system, please follow the steps below. Type the following statements under UNIX system. I. Cd /UM8673.bin II. ./rm.um8673 (9). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Trademark Acknowledgments ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ MS-DOS and Windows are registered trademarks of Microsoft Corporation. OS/2 is a registered trademark of IBM Corporation. NetWare is a registered trademark of Novell Corporation. Other brand names or trademarks are registered trade marks of their respective holders.