HP ProLiant ML150 G2 Server Support CD

∩╗┐ HP ProLiant ML150 G2 Server Support CD

┬╗ Contact HP

┬á


	┬á	HP ProLiant ML150 G2 Server Support CD System Support Software

┬╗┬á

CD Home Page

┬á


┬╗┬á System Support Software

┬á	┬╗┬á	Microsoft Windows 2000
┬á	┬╗┬á	Microsoft Windows Server 2003
┬á	┬╗┬á	Novell NetWare 6.5
┬á	┬╗┬á	Red Hat Enterprise Linux 3 (x86)
┬á	┬╗┬á	Red Hat Enterprise Linux 3 (x86_x64)
┬á	┬╗┬á	SCO OpenServer 5
┬á

┬á
┬╗┬á	Documents
┬á

┬á
┬╗┬á	Release Note

┬á

┬á

┬á

HP ProLiant NC150T PCI 4-port Gigabit Combo Switch NIC Driver for SCO OpenServer 5

HP ProLiant NC150T PCI 4-port Gigabit Combo Switch NIC Driver for SCO OpenServer 5
┬áversion 7.5.18 ┬á (18┬áJun┬á2004)


Click the link below to download this software:

vol.000.000

HP ProLiant NC150T PCI 4-port Gigabit Combo Switch NIC Driver for SCO OpenServer 5

software information

┬á┬áInstallation		┬╗ top of page

Creating Floppy =============== 1.Copy the file VOL.000.000 to an SCO system. 2.Create the floppy using dd if=VOL.000.000 of=/dev/rfd0135ds18. Installing Driver ================= 1.Use custom or scoadmin software to install the driver from the media image or from the floppy created above. 2.After the package is installed, use netconfig to add the new network adapter and configure network protocol and address. 3.Once the adapter is added, modify the hardware configuration in Advanced Options to change line speed and flow control if desired. The different settings of these parameters are listed below: -- LineSpeed: AutoNegotiate (default) (all speeds advertised) -- FixedHalfDduplex10 -- AutoHalfDduplex10 (only 10 Mbps half duplex advertised) -- FixedFullDduplex10 -- AutoFullDduplex10 (only 10 Mbps full duplex advertised) -- FixedHalfDduplex100 -- AutoHalfDduplex100 (only 100 Mbps half duplex advertised) -- FixedFullDduplex100 -- AutoFullDduplex100 (only 100 Mbps full duplex advertised) -- AutoHalfDduplex1000 (only 1 Gbps half duplex advertised) -- FixedFullDduplex1000* -- AutoFullDduplex1000 (only 1 Gbps full duplex advertised) -- FlowControl: AutoNegotiate** (Symmetric Pause advertised) (default) -- Off -- RxPause -- TxPause -- RxPause/TxPause Note that 1000 Mbps (1 Gbps) full duplex fixed speed is only valid for fibre connections. For copper twisted pair connections, 1 Gbps can only be set through auto negotiation with a 1 Gbps link partner *Note that auto negotiation of flow control is only valid when the line speed is set to auto negotiation (all speeds advertised or single speed advertised). A kernel rebuild and reboot is required before the new configuration will take effect.

┬á┬áRevision history		┬╗ top of page

Version 7.5.18 Initial revision


Privacy statement	Using this software means you accept its terms	Terms and conditions of sale and service

┬⌐ 2004 Hewlett-Packard Development Company, L.P.