DOS Client Message File: IPXODI.COM 0, Tran 0
Message file %s is invalid.
Program load aborted.
CoPyRiGhT=(C) Copyright 1990-1995 Novell, Inc.  All Rights Reserved.
IPX protocol has been successfully removed.
Bound to logical board %u (%s) : Protocol ID %s
Available command line options:
/?     Display this help screen.
/D     Eliminate Diagnostic Responder - Reduces size by 3K.
/A     Eliminate Diagnostic Responder and SPX - Reduces size by 9K.
/M     Use NetWare Mobile IPX support. Do not use this option unless a
       Home Router is installed on your network. Using /M without a Home
       Router disables network connectivity. This option overrides the /D
       and /A options.
/C=[path\]filename.ext
       Specify a configuration file to use (Default is NET.CFG).
/U     Unload resident IPXODI from memory.
/F     Forcibly unload resident IPXODI from memory, regardless of programs 
       loaded above it.  Using this option can cause a machine to crash if
       applications are still using IPX/SPX.
The IPX protocol has already been loaded.
The LSL is not loaded.  Please load the LSL then IPXODI.
The loaded LSL is too old.  LSL.COM must be 1.20 or later.
Cannot find an IPX protocol to unload.
Cannot unload IPXODI because another program has been loaded
above it.  Unload the other program or programs and try again.
IPXODI cannot be unloaded because the installed IPXODI is a 
different version than this IPXODI module.
IPXODI cannot be unloaded because interrupt 0x%X is owned by 
another program.  Unload the other program then unload IPXODI.
A network adapter driver must be loaded before IPXODI.COM can
be loaded.
IPX could not find a board to bind to.  Please specify a board
in the NET.CFG file by adding a "BIND" entry to the "PROTOCOL IPX" section
and specify the protocol ID IPX should use for that board by adding a
"PROTOCOL IPX id frametype" entry to the board's "LINK DRIVER" section.
IPX cannot bind to board "%u" because a IPX protocol ID for 
the "%s" frame type has not been registered with the LSL.
Please register an ID by adding a "PROTOCOL IPX id %s" entry
to the "LINK DRIVER %s" NET.CFG section, replacing "id" with the
appropriate protocol ID for IPX to use on this frame type.  For the new ID to
be recognized the %s LAN Driver must be reloaded.
Maximum number of stacks already loaded.  Either unload an
existing stack or increase the maximum by adding a "MAX STACKS" entry to
the "LINK SUPPORT" section in the NET.CFG file.
Attempt to register an IPX Protocol ID failed.  Increase the
maximum number of stacks in the LSL.COM by adding a "MAX STACKS" entry
to the "LINK SUPPORT" section in the NET.CFG file.
An IPX protocol stack is already registered with the LSL.
Invalid command line option was specified: "%s".
Missing or invalid value for "%s"
parameter was specified on line %u of the configuration file.
Entry was ignored.
Missing or invalid ON/OFF value for "%s"
parameter was specified on line %u of the configuration file.
Entry was ignored.
Missing or invalid IPATCH values were specified on line %u of
the configuration file.  Entry was ignored.
Specified board in "BIND" statement on line %u of the
configuration file does not exist.  Entry was ignored.
Invalid "BIND" statement on line %u of the configuration file.
Requires a board number (Example, BIND 2).  Entry was ignored.
Duplicate "BIND" statement on line %u of the configuration 
file.  IPXODI cannot be bound to more than one board.  Entry was ignored.
An invalid entry was found on line %u of the configuration
file.  Entry "%s" ignored.
Failed to locate configuration file "%s".
NET.CFG will be used.
NESL.COM must be loaded before Mobile IPX support 
may be enabled.
Mobile IPX successfully registered with NESL.
The alternate board specified in the configuration file is not
        loaded. Mobile IPX will only use the primary board for communication.
Unable to register with NESL.COM to receive necessary events.