Novell Help Librarian Data File Version 1.00 COPYRIGHT (c) 1985 by Novell, Inc. All Rights Reserved. No help is available for this option. (Press to continue) Product Installation Help 1 of 1 This installation program performs the following steps: 1. Checks that enough disk space is available to install the product. 2. Makes sure that TCP/IP is configured. 3. Makes sure that the internet hostname for the server is specified. 4. Checks whether any files might be overwritten by this installation. Allows you to specify whether any such files are overwritten. 5. Copies the product files to the system disk. 6. Configures the product (additional manual steps may be required). The product software can be installed from the distribution diskettes, from a DOS drive, or from a NetWare volume. Press the key at any step in the installation process to display help information. (Press to continue) Serial Number Overwrite Help 1 of 1 Overwriting the serial number will cause problems if the product is already installed with the same serial number on another system. (Press to continue) Files to Overwrite or Preserve Help 1 of 1 This list shows the files that are present on the system and can be overwritten during installation. Use this list to indicate whether each file is overwritten or kept unchanged. Mark each file to be overwritten by highlighting the filename and pressing the key. All files that you do not mark using are kept unchanged and are not overwritten. If you do not mark any files, none of the files are overwritten. When you finish marking files, press the key to continue the installation process. (Press to continue) Boot Drive Help 1 of 1 Specify the complete path for the directory from which NetWare is booted. This path is where SERVER.EXE is located. SERVER.EXE might be on a hard disk drive (for example, C:\NETWARE), or on a boot diskette. If you boot NetWare from a diskette, make a note of the diskette label. (Press to continue) TCP/IP Configuration Help 1 of 1 This product can be installed properly only if TCP/IP is configured. If TCP/IP is not configured properly, the installation program lets you switch to the console screen to do the configuration. Refer to the NetWare TCP/IP Transport Supervisor's Guide for instructions. Once TCP/IP is configured, the installation program checks whether an internet name is assigned to your server. If no name corresponds to the IP address you used to configure TCP/IP, the installation program prompts you for the local hostname. The hostname consists of alphanumeric characters only, no dots or spaces. You cannot continue the installation until you configure TCP/IP and specify the local hostname. (Press to continue) File Transfer Help 1 of 1 This step transfers files from the source diskette to the NetWare partition. (Press to continue) Destination Volume Help 1 of 1 Select the NetWare volume on which you want to install the product. Highlight the volume and press the key. The list shows only volumes that are present and mounted. If the volume you want is not listed, press the key to exit installation, mount the volume, and repeat the installation. (Press to continue) Configuration Form Help 1 of 1 This form allows you to enter the following parameters: IP Address Hostname Subnetwork Mask Maximum Packet Size Minimum Receive Buffers LAN Driver The form provides the format for the IP Address, subnetwork mask, and hostname, and provides default values for the remaining parameters. (Press to continue) Caution: Help File is Missing The help file that contains the online help screens is not present is the SYS:SYSTEM directory. The program will attempt to transfer the file to the SYS:SYSTEM directory from the diskette. If the transfer is successful, you should be able to view help screens the next time you next run the program. (Press to continue) Editing Keystrokes Help 1 of 1 Arrow Keys - Move the cursor - Insert a character - Delete a character - Scroll forward one screen - Scroll back one screen - Scroll to the start of the file - Scroll to the end of the file - Cursor to the start of the line - Cursor to the end of the line - Exit the editor (Press to continue) STARTUP.NCF Path Help 1 of 1 Enter the full path of the directory where the STARTUP.NCF file is stored. The installation program will modify the STARTUP.NCF file. (Press to continue) Key Assignments Help 1 of 1 The function key assignments on your machine are: ESCAPE Back up to the previous level EXIT Exit the program INSERT Insert a new item DELETE Delete an item SELECT Accept information entered HELP Provide online help (Press to continue)