#
Nothing
No  function selected. For general information  see
the manual.
#
Script 16/32 pixels
  arrow keys - move by characters
   PgUp/PgDn - move for 256 pixels
 ^Left/Right - move to borders of the current line
 +arrow keys - move by pixels
      Return - normal function
    Home/End - normal function
   ^Home/End - move to the picture borders
   Backspace - for the last 128 characters
    Esc/+Esc - switch script style
 extra chars - 2 levels, click on number to swap
               levels
#
Script DIN 6776 B
   arrow keys - move by characters
    PgUp/PgDn - move by 256 pixels
  ^Left/Right - move to borders of the current line
  +arrow keys - move by pixels
       Return - normal function
     Home/End - normal function
    ^Home/End - move to picture borders
    Backspace - for the last 128 characters
<,>,$,],#,/,^ - extra characters

DIN-script 2,5 mm only uses capitals !
#
Script fonts
   arrow keys - move by characters
    PgUp/PgDn - move by 256 pixels
  ^Left/Right - move to borders of the current line
  +arrow keys - move by pixels
       Return - normal function
     Home/End - normal function
    ^Home/End - move to picture borders
    Backspace - for the last 128 characters
     Esc/+Esc - switch fonts

Character and line distance can be changed at  FONT
PARAMETERS.
#
Erase/invert block
Choose  two corners of the block with left  button,
cancel with right button.
Erase cannot be cancelled !
#
Copy/move block
Choose  two corners of the block with left  button,
cancel with right button.
Move  the block to its new position and press  left
button to insert the block.
Moving a block will erase the source !
The drawing mode is considered.
The block is still in the buffer at the end of  the
operation.
The buffer will be changed !
#
Lasso
First frame the area that shall be moved or  copied
with the lasso. This is done with a polyline of  up
to 512 lines.
Select the points with the left button. ESC removes
the  last line selected (as often as wanted).  When
ready, press the right button. A dialog appears.
Click  on  EXECUTE to select the framed  area.  The
polyline  is  closed automatically. After  a  short
calculation  the  area can be moved like  a  normal
block.
Insert the area by pressing the left button, cancel
with  the  right button. When  moving,  the  source
block is erased. Drawing mode is considered.
The block is still in the buffer at the end of  the
operation, but the frame information is lost.
The buffer will be changed !
#
Block operations
Choose  two corners of the block with left  button,
cancel with right button. Move the changed block to
its  new position and press left button  to  insert
the block.
Drawing mode is considered.
The block is still in the buffer at the end of  the
operation.
The buffer will be changed !
#
Resize block
Choose  two corners of the block with left  button,
cancel with right button.
Resize  the block by moving the mouse and  pressing
left button, then move the resized block to its new
position and press left button to insert the block.
Drawing mode is considered.
The block is still in the buffer at the end of  the
operation.
The buffer will be changed !
#
Rotate block
First choose upper left and then lower right corner
of  the block with left button, cancel  with  right
button.
Turn the block as wanted and press left button. The
angle is shown.
Move  the  rotated block to its  new  position  and
press left button to insert the block.
Drawing mode is considered.
The block is still in the buffer at the end of  the
operation.
The buffer will be changed !
#
Sheer block
Choose  two corners of the block with left  button,
cancel with right button.
Sheer  the block by moving the mouse  and  pressing
left button, then move the sheered block to its new
position and press left button to insert the block.
Drawing mode is considered.
The block is still in the buffer at the end of  the
operation.
The buffer will be changed !
#
Read buffer
Choose  two corners of the block with left  button,
cancel with right button.
The buffer will be changed !
#
Insert buffer
Press  left  button to show the  buffer.  Move  the
buffer to its position and press left button  again
to insert the buffer, right button to cancel.
The buffer can be inserted several times.
Drawing mode is considered.
#
Point
Press left button to draw a point.
Drawing mode and line width are considered.
#
Line/polyline
Choose end points of lines with left button, cancel
with right button.
Length  of line and the angle between the line  and
horizontal are shown.
Drawing mode and line pattern are considered.
#
Triangle
Choose three corners with left button, cancel  with
right button.
Length  of side and the angle between the side  and
horizontal are shown.
Drawing  mode,  filling mode and line  pattern  are
considered.
#
Rectangle
Choose  two corners with left button,  cancel  with
right button.
Horizontal and vertical size are shown.
Drawing  mode,  filling mode and line  pattern  are
considered.
#
Rhomb
Choose  center  and  one point  with  left  button,
cancel with right button.
The angle between one side and horizontal is shown.
Drawing  mode,  filling mode and line  pattern  are
considered.
#
Parallelogram
Choose three corners with left button, cancel  with
right button.
Length  of side and the angle between the side  and
horizontal are shown.
Drawing  mode,  filling mode and line  pattern  are
considered.
#
Polyeder/circle (3)
Choose three points on the circle with left button,
cancel with right button.
While choosing the 3rd point, the radius is shown.
Drawing   mode,  filling  mode  and  line   pattern
(polyeder) are considered.
#
Polyeder/circle (C+1)
Choose the center and one point on the circle  with
left button, cancel with right button.
While choosing the 2nd point, the radius is shown.
Drawing   mode,  filling  mode  and  line   pattern
(polyeder) are considered.
#
Circle arc (3)
First choose both end points, then 3rd point on the
circle with left button, cancel with right button.
While choosing the 3rd point, the radius is shown.
The  arc  is drawn anti-clockwise from 1st  to  2nd
point.
Drawing mode is considered.
#
Circle arc/sector
Choose center, a point on the circle and two angles
with left button, cancel with right button.
While choosing the 2nd point, the radius is  shown,
while choosing 3rd and 4th, the angle is shown. The
arc/sector is drawn anti-clockwise from 1st to  2nd
angle.
Drawing   mode  and  filling  mode   (sector)   are
considered.
#
Circle ring
Choose  common  center and a point on  each  circle
with left button, cancel with right button.
While  choosing  2nd and 3rd point, the  radius  is
shown.
Drawing mode and filling mode are considered.
#
Circle ring sector
Choose  common center, a point on each  circle  and
two  angles  with left button,  cancel  with  right
button.
While  choosing  2nd and 3rd point, the  radius  is
shown,  while  choosing 4th and 5th, the  angle  is
shown.
The sector is drawn anti-clockwise from 1st to  2nd
angle.
Drawing mode and filling mode are considered.
#
Ellipse (C+2)
Choose  center  and two points  with  left  button,
cancel with right button.
While  choosing  2nd  and  3rd  point,  length  and
orientation of the vector from center to point  are
shown.
Drawing mode and filling mode are considered.
#
Ellipse (C+1)
Choose  center  and  a  point  on  the  surrounding
rectangle  with  left  button,  cancel  with  right
button.
While  choosing the 2nd point, the  coefficients  a
and b are shown.
Drawing mode and filling mode are considered.
#
Ellipse arc/sector
Choose center, a point on the surrounding rectangle
and two angles with left button, cancel with  right
button.
While  choosing the 2nd point, the  coefficients  a
and  b are shown, while choosing 3rd and  4th,  the
angle is shown.
The arc/sector is drawn anti-clockwise from 1st  to
2nd angle.
Drawing   mode  and  filling  mode   (sector)   are
considered.
#
Ellipse ring
Choose   common   center  and  a  point   on   each
surrounding rectangle with left button, cancel with
right button.
While choosing 2nd and 3rd point, the  coefficients
a and b are shown.
The two ellipses should not cross !
Drawing mode and filling mode are considered.
#
Ellipse ring sector
Choose  common center, a point on each  surrounding
rectangle  and two angles with left button,  cancel
with right button.
While choosing 2nd and 3rd point, the  coefficients
a  and b are shown, while choosing 4th and  5th,the
angle is shown.
The two ellipses should not cross !
The sector is drawn anti-clockwise from 1st to  2nd
angle.
Drawing mode and filling mode are considered.
#
Print section
Choose  two corners with left button,  cancel  with
right button.
Horizontal and vertical size are shown.
Printing  can  be stopped by pressing a  button  or
ESC.
#
Magnifier
Press  left  button  to  show  outline.  Move  this
outline  to the section to be magnified  and  press
left button again, cancel with right button.
The  section  is displayed enlarged by  8,  in  the
lower  right  corner twice in original  size  (OLD,
CURRENT).
Set  point by pressing left button, erase point  by
pressing right button.
Sliders can be used as normal, but all changes will
be accepted before scrolling.
ACCEPT  exits  magnifier  accepting  all   changes,
CANCEL exits restoring current section.
#
Brush
Press left button to show outline representing  the
brush.
While  pressing  left button, an object  of  chosen
size is inserted, cancel with right button.
Drawing mode and filling pattern are considered.
#
Eraser
Press left button to show outline representing  the
eraser.
While  pressing  left button, a section  of  chosen
size is erased, cancel with right button.
Drawing color is considered.
#
Free style drawing
While pressing left button, a line will follow  the
moves of the mouse.
Drawing mode and line pattern are considered.
#
Airbrush
While pressing left button, the airbrush sprays  to
the picture.
Density  and  size  can be  changed  with  AIRBRUSH
PARAMETERS.
Drawing mode is considered.
#
Fill area
Any  area bordered in drawing color can  be  filled
with the filling pattern.
Choose any point within the area with left button.
Be sure that the border is complete, else the whole
picture might be filled.
#
Lines DIN 15
Choose end points of line with left button,  cancel
with right button.
Length  of line and the angle between the line  and
horizontal are shown.
Drawing mode is considered.
#
Arrows DIN 406, straight
Choose end points of line with left button,  cancel
with right button.
Length  of line and the angle between the line  and
horizontal are shown.
Drawing mode is considered.
#
Arrows DIN 406, curved
Choose center, a point on the circle and two angles
with left button, cancel with right button.
While choosing the 2nd point, the radius is  shown,
while choosing 3rd and 4th, the angle is shown.
The arrow is drawn anti-clockwise from from 1st  to
2nd angle.
Drawing mode is considered.
#
Measure distance DIN 406
Choose  end  points of distance with  left  button,
cancel with right button.
The calculated value is shown as a block and can be
inserted  by pressing the left button, cancel  with
right button.
The value depends on the chosen scale.
The buffer is changed !
#
Measure angle/arc DIN 406
Choose center, a point on the circle and two angles
with left button, cancel with right button.
While choosing the 2nd point, the radius is  shown,
while choosing 3rd and 4th, the angle is shown.
The calculated value is shown as a block and can be
inserted  by pressing the left button, cancel  with
right button.
The buffer is changed !
#
Measure/arrow distance DIN 406
Choose  end  points of distance with  left  button,
cancel with right button.
The  arrow is drawn (drawing mode  is  considered),
the calculated value is shown as a block and can be
inserted  by pressing the left button, cancel  with
right button.
The value depends on the chosen scale.
#
Measure/arrow angle/arc DIN 406
Choose center, a point on the circle and two angles
with left button, cancel with right button.
While choosing the 2nd point, the radius is  shown,
while choosing 3rd and 4th, the angle is shown.
The  arrow is drawn (drawing mode  is  considered),
the calculated value is shown as a block and can be
inserted  by pressing the left button, cancel  with
right button.
The buffer is changed !
#
Mark
Choose  end  points  of reference  line  with  left
button, cancel with right button.
While  choosing 2nd point, length of line  and  the
angle between the line and horizontal are shown.
Choose  point  to be marked.  While  choosing  this
point,  length  of line 1st point - 3rd  point  and
angle  between  this line and  reference  line  are
shown.
After  choosing 3rd point with left button,  it  is
inverted. Cancel with right button.
#
Drop perpendicular
Choose  end  points  of reference  line  with  left
button, cancel with right button.
While  choosing 2nd point, length of line  and  the
angle between the line and horizontal are shown.
Choose end point of perpendicular with left button,
cancel with right button.
While  choosing 3rd point, length of  perpendicular
(distance point - reference line) is shown.
Drawing mode and line pattern are considered.
#
Draw angle
Choose  end  points  of reference  line  with  left
button, cancel with right button.
While  choosing 2nd point, length of line  and  the
angle between the line and horizontal are shown.
Choose  end  point of second line.  While  choosing
this  point, length of line 1st point -  3rd  point
and angle between this line and reference line  are
shown.
Drawing mode and line pattern are considered.
#
Append circle arc
Choose  two  points  of reference  line  with  left
button, cancel with right button.
2nd point is starting point of the arc !
While  choosing 2nd point, length of line  and  the
angle between the line and horizontal are shown.
Choose end point of arc to be appended.
While choosing this point, the calculated radius is
shown.
Drawing mode is considered.
#
Parallel
Choose  two  points  of reference  line  with  left
button,  cancel  with right button.  1st  point  is
starting point of the parallel.
While  choosing 2nd point, length of line  and  the
angle between the line and horizontal are shown.
Choose  end point of the parallel.  While  choosing
this  point,  the length of the  parallel  and  the
distance to the reference line are shown.
Drawing mode and line pattern are considered.
#
Bézier curve
Choose  four points (starting point -  two  control
points  - end point) with left button, cancel  with
right button.
While choosing 2nd to 4th point, length of line and
the  angle between line and horizontal  are  shown,
while  choosing 4th point, the resulting  curve  is
shown.
After  all  points are chosen,  a  window  appears.
Click  on or type 1 to 4 to move a point, click  on
EXECUTE to accept the curve.
Drawing mode is considered.
#
Text editor
Choose two corners of section to be used by  editor
with left button, cancel with right button.
Horizontal and vertical size are shown.

  arrow keys - move by character
    Home/End - move to borders
   PgUp/PgDn - move 4 lines up/down
   (num) +/- - line   buffer
      Insert - buffer  text
     +Insert - insert line
     +Delete - delete line
^Y/Backspace - clear line
   ^Return/J - end of paragraph on/off

Leave editor by pressing right button, choose  text
format by clicking it on. The buffer is changed !
#
Read character
Choose  two  corners  of  the  section  to  be  the
character  with  left  button,  cancel  with  right
button.
Horizontal and vertical size are shown.
Choose the key, which the character is supposed  to
be, by clicking it on or pressing the key.
A character may have 400 x 480 pixels.
#
Read symbol
Choose two corners of the section to be the  symbol
with left button, cancel with right button.
Horizontal and vertical size are shown.
A library may contain up to 128 symbols.
#
Insert symbol
Press  left  button to show symbol  select  window.
Choose  the symbol. It is copied to the buffer  and
can be inserted with left button, cancel with right
button.
Drawing mode is considered.
The buffer is changed !
#
