MKMSGF
os2ldr.msg
IThe system cannot swap in a segment.
EA program in this session encountered a problem and
cannot continue.
PLoading, please wait. %1.
                 
     
       
                 
     
                   
      
                   
      
     
                   
      
     
                   
      
                 
                 
     
            
            
              IBM Operating System/2                 
            
            Corrective Service Facility              
            
           (C) Copyright IBM Corp. 1981, 1992, 1993.  All rights reserved.
           Remove the diskette from drive A.
           Insert Corrective Service Diskette 2 into drive A.
           Then, press Enter.
IOS/2 could not start because an IFS= statement
is not included in the CONFIG.SYS file.  Add the
IFS= statement (containing the correct file system name)
to the CONFIG.SYS file and restart your system.
EThe parameter "%3" on line %1 of the CONFIG.SYS
file is not acceptable for the %2 command. Line %1 is
ignored.
IOS/2 cannot be started.
The error code is:
EThe device driver "%3" specified in the %2 command
on line %1 of the CONFIG.SYS file was not installed. Line %1
is ignored.
IThe device driver "%1" that is needed to start
the system failed to install.
Install the correct device driver in the root directory in
either the root directory, or the /OS2 subdirectory of the
startup device; then, restart the system.
EAn Input/Output privilege level is required
for the program or device driver %3 specified in the
%2 command on line %1. Line %1 is not used.
EAn Input/Output privilege level is required
for the program or device driver %1.
IThe device driver "%3" specified in the %2
command on line %1 of the CONFIG.SYS file has modified DOS
mode system storage.
Correct the problem in the device driver, or edit the
CONFIG.SYS file to remove the DEVICE command.
Then restart the system.
EThere is not enough storage to load the program
or device driver "%3" specified in the %2 command on
line %1 of the CONFIG.SYS file.  Line %1 is ignored.
***************************************************
*    ------Possible System Failure-------         *
*           The swap file is full.                *
***************************************************
IThe system cannot find the file "%1". This device
driver, program, or data file is not located in the default
path or the path specified for it in the CONFIG.SYS file.
Install this file in the correct directory, or correct the
appropriate CONFIG.SYS file statement.
EThere is not enough storage to load the program
or device driver "%1".
IThe system cannot load the startup file system. The
information for the startup file system is not correct. Reinstall
your system.
IThe system cannot initialize the startup file system.
Reinstall your system.
EThe system cannot find the file "%3" specified
in the %2 command on line %1 of the CONFIG.SYS file.
Line %1 is ignored.
EThe file "%3" specified in the %2 command
on line %1 of the CONFIG.SYS file does not contain a
valid device driver or file system driver.  Line %1 is ignored.
IThe information needed to IPL the system is not
acceptable.
                        Operating System/2 Version 2.1
  (C) Copyright IBM Corp. 1981, 1994.  All rights reserved.
  US Government Users Restricted Rights - Use, duplication or disclosure
             restricted by GSA ADP Schedule Contract with IBM Corp.
IThe system cannot load the dynamic link library %1
which is needed to start the system.
Install the dynamic link library in the root directory of
the startup drive or in the directory specified in the
LIBPATH command in the CONFIG.SYS file.
IThe system cannot find the entry point %2 in
dynamic link library %1 which is needed to start the system.
Install the correct dynamic link library in the root
directory of the startup drive or in the directory
specified in the LIBPATH command in the CONFIG.SYS file.
IThe system cannot open the CON: file, which is
needed to start the system.
IThe handle for the CON: file is not zero.
Press Enter to continue.
EThe country information file "%1" is incorrect.
The system detected a divide by zero error.
IThe system detected an internal processing
error at location %1.
The system is stopped.  Record the location number
of the error and contact your service representative.
EThe file "%3" specified in the %2 command on
line %1 of the CONFIG.SYS file does not contain a valid
program. Line %1 is ignored.
E A program in this session encountered a problem and
cannot continue.
E A program in this session encountered a problem and
cannot continue.
EThe file "%1" does not contain a valid program.
IThe system detected a general protection
fault (trap D) in a system call.
Arguments used in system call (high to low):
EThe system does not have enough storage
to reload a code or data segment.
IThe system detected an interrupt that cannot be masked.
EThe system detected a hardware memory error on the system board.
The hardware memory error occurred at physical location %1.
Make a note of the location and read the message help.
The system stopped.
Run the diagnostics supplied with your system to
determine the cause of the problem.
IThe system detected a hardware memory error
on an option card.
The system stopped.
Run the diagnostics supplied with your system to
determine the cause of the problem.
IThe system detected a timeout on the DMA channel
of the hardware.
The system stopped.
Run the diagnostics supplied with your system to
determine the cause of the problem.
IThe system detected a timeout by the watchdog
timer on the system board.
The system stopped.
Run the diagnostics supplied with your system to
determine the cause of the problem.
IA disk read error occurred.
PInsert a system diskette and restart
the system.
IThe system cannot find the OS2KRNL file.
IThe file OS2KRNL is not acceptable.
IThe system does not have enough storage to
start the operating system.
The system is stopped.
Correct the preceding error and restart the system.
IThe file "%1" does not contain a valid device
driver. Install the correct device driver file; then restart
the system.
EA program in this session encountered a problem and
cannot continue.
EThe system detected a Software generated error.
The system stopped.
EThe system detected a bus timeout error.
The system stopped.
EThe system detected a fail-safe timer error.
The system stopped.
EThe system detected an I/O check error.
The system stopped.
EThe system detected a hardware memory error
on the system board.
The system stopped.
Run the diagnostics supplied with your system to determine the cause of the
problem.
EBad or missing command interpreter.
Press Enter to close the DOS session.
IThe system detected an Intel 8086
or an 80286 CPU that is not supported by
this version of the OS/2 operating system.
An Intel 80386 or compatible CPU is required.
IThe system detected an Intel 80386 CPU
stepping (B0) that is not supported by the
OS/2 operating system.  Contact your hardware
service representative or replace your 80386 CPU.
IThe system detected an Intel 80386 CPU
that does not reliably execute 32-bit multiply
operations and cannot be supported by the OS/2
operating system.  Contact your hardware service
representative or replace your 80386 CPU.
EA program in this session encountered a problem and
 cannot continue.