Summary of information on the SR&D MCR-175-1R-0803 mag stripe card
reader. Due to the large volume of summary requests I received, I am
posting this summary instead of mailing it. It's somewhat long, so hit
'n' now if you're not interested in this stuff.
[Editor's Note: The following is a concatenation of the replies I received
to a net.request about my mag stripe card reader. After the replies I have
included some software that I threw together to play with the card reader.
This file contains all the information I have on this subject.
Additions are most welcome. Note also that there was another summary
post in recent days with information on how the data on the cards is
encoded. See article for this info.
You'll notice I didn't get any farther than simply reading the raw signal
from the card; of the two card readers I ordered, one was completely DOA,
and the other had a faulty clock output (at least I assume that it was a
clock output; I was never able to read any sort of signal from that line).
Someone with a fully functional reader can easily extend what I wrote to get
it to decode the actual data content of the card. If you do decide to make
modifications and/or extensions, I'd appreciate a copy of whatever
changes you make (email to tmkk@uiuc.edu). Enjoy!]
---
Subject: Re: Mag Card Swipe Reader: Need Help!
I am truly amazed that someone else is trying to use this device! I got
mine about 2 years ago and spent some time trying to find the manufacturer.
I found a listing for SR&D in the Noth America technical directory at
the public library. I found the listing for the American sales office
in Los Angeles. I tried calling but the company had gone out of
business. There was no listing in the local phone directory either.
I then tried calling the head office in Japan, but they also had
gone out of business. I haven't seen the company listed in any recent
electronics directories, so I think they really are gone.
I have spent about an hour looking at the signals on the outputs
of the device. One signal line is a /STATUS line which indicates
when a card is been moved through the unit. The other 2 lines
pulse in response to a magnetic card. I believe the IC performs
Manchester decoding and clock recovery for the read channel, so one
output line is DATA and the other is CLOCK.
That is as far as I got 2 years ago and I had forgot about it until
now. If you receive any other info, please send a copy to me!
---
>Finally, there are 5 wires coming from the assembly and terminating in a
>small connector similar to power supply connectors for 3.5" floppy drives.
>The wires are red, yellow, green, blue, and black.
If its anything like the units I worked with, I think you will find
that the five wires are:
+5v
Gnd
Clock
Data
Card detected
But I don't know active levels, or which wire is what.
---
I picked few week ago a magnetic credit card reader from a
another surplus outfit. It cost about the sam es yours.
My card reader was made by MAGTEK and was diffrent from
your reder in many ways. The reader I have has 4 ICs and
some of them are standard TTL chip, so I could easily
quess the power requiments (5V) and power connectors.
My card reader had 6 pin connector.
I put the power to the reader and started to examine
the signals with multimeter and a little crystal
earphine (my favourite electronics hacking tool).
I found that output signals were something like
that: data out, data clock out, data readable and
and card ath the end of the reader.
Then I connected the reader to the joystick port
of my 386SX and made a little Turbo Pascal program
for reading the card.
Spare printer port is the interface I use very often to connect
diffrent hardware circuit to my computer. This time I decided
to use game port beacuse it can also provide the power to the
reader.
My program simply prints out the bits from the card. I have not
found the way to decode the bits to corresponding numbers. The
program so prints all 237 bits form the card to screen.
If you have any information about data coding, I an interrested
in hearing that.
Here is the meanings of the bytes in port $201:
D7: 0 -> card pushed to the end of the reader
D6: the read data from card
D5: 0 -> data stream readable
D4: the data clock
Program CardReader;
Uses Crt,Binary;
Const
gameport=$201;
Procedure Wait_start;
Begin
Repeat Until (Port[gameport] and 32)=0;
End;
Function data_readable:boolean;
Begin
data_readable:=((Port[gameport] and 32)=0);
End;
Procedure Wait_clock;
Begin
Repeat Until (Port[gameport] and 16)=0;
End;
Procedure Wait_clock_end;
Begin
Repeat Until (Port[gameport] and 16)=16;
End;
Function data_input:byte;
Begin
If (Port[gameport] and 64)=0 Then data_input:=0
Else data_input:=1;
End;
Function card_at_end:boolean;
Begin
card_at_end:=((Port[gameport] and 128)=0);
End;
Procedure test;
Begin
Wait_start;
Repeat
Writeln(ByteBin(Port[$201]));
Until keypressed;
End;
Begin
ClrScr;
Wait_start;
While data_readable Do Begin
Wait_clock;
Write(data_input);
Wait_clock_end;
End;
Repeat Until KeyPressed;
End.
---
Wiring color code for the SR&D MCR-175-1R-0803 mag stripe card reader:
Red: +5V
Black: Gnd
Yellow: /Card Detect
Green: Clock (?? - non-functional on the unit I have)
Blue: /Data
The leading '/' indicates an active low TTL signal.
---
Quick 'n Dirty guide to the enclosed reader software
----------------------------------------------------
Hooking the SR&D MCR-175-1R-0803 card reader to your PC:
The included software is written specifically for the following
configuration; if your wiring is different, you'll need to make
corresponding changes to the software. Note also that the port
address is hard-coded to look for LPT2's status port (at address
0x279). If you're using a different port address, be sure to change the
port address value.
SR&D Wire Printer Port Pin Port Bit Signal
--------- ---------------- -------- ------
Yellow 11 7 /CARD DETECT
Blue 10 6 /DATA
Black 18 N/A (Ground)
Power to the reader was provided by a separate power supply, basically
one of those black plastic DC power packs fed through a 7805 regulator
chip.
Compiling the software:
Compile SWIPE.C (using SMALL memory model), assemble SWIPEISR.ASM, and
link the two together.
Using the software:
To use SWIPE.EXE, simply hook the reader up to your LPT2: port, power it
up, then run SWIPE. When you're ready, press the ENTER key, and swipe a
card through the reader. The program will read the data from the card and
store it in a buffer (but will not decode the data; that is left as an
excercise ;-). After the card has been read, press ENTER again and the
contents of the buffer will be dumped to stdout. To save the card data to
a file, simply redirect SWIPE's output on the command line, e.g.
SWIPE > citibank.out
Please let me know of any changes, bug fixes, or improvements you make to
this code. Send email to tmkk@uiuc.edu.
Thanks, and have fun!
--- CUT HERE ---
/*
* S W I P E . C
*
* Written:
* 1/11/92
*
* Description: Quick 'n Dirty reader program for SR&D mag stripe card reader.
* Reads data from the input port as long as a card is detected in the
* card slot. After sampling, the data is dumped to stdout, and may
* be redirected to a file if desired.
*
* Note: Written for Borland C++ 3.0 - may require changes to compile under
* MSC or others. Compile in SMALL model.
*
*/
#include
#include
#include
#include
#include
#include
#include
#include
/* timer chip programming register port addresses */
#define COMMAND_REG 0x43
#define CHANNEL0 0x40
/* size of sample buffer */
#define MAXSAMPLE 4096
typedef unsigned char byte;
/* global variables */
byte *databuf; /* buffer for the sampled data */
/* interprocess communication data */
byte *bufp; /* data buffer pointer */
unsigned nsamp; /* number of samples to be made */
unsigned port; /* input port address */
int enab=0; /* flag to enable/disable sampling */
int start=0; /* flag indicating that sampling has begun */
/* ISR prototype */
extern void interrupt shand(void);
void program_timer(int channel, unsigned count)
/*
* P R O G R A M _ T I M E R
*
* Description: Programs the given count value into the specified channel of
* the IBM 825x timer chip. Channel 0 is the time-of-day-clock interrupt;
* channel 2 is the speaker pulser.
*
* Parameter:
* channel (in) - Channel to be programmed.
* count (in) - Count value with which to program timer chip.
*
*/
{
outportb(COMMAND_REG, 0x36); /* set up for reprogramming */
outportb(CHANNEL0 + channel, count & 0xff); /* lo byte first */
outportb(CHANNEL0 + channel, count >> 8); /* then hi byte */
}
void sample_data(int count)
/*
* S A M P L E _ D A T A
*
* Description: Sets up for data collection from the printer port using
* the SHAND interrupt service routine (see SWIPEISR.ASM). This routine
* reprograms the timer chip for the desired sampling rate, sets up
* the interprocess communication area, and starts the sampling process.
* The actual sampling is done in the SHAND procedure. This routine
* waits until sampling has been completed before returning.
*
*/
{
void interrupt (*oldhand)(void); /* pointer to old interrupt vector */
/* save old interrupt vector */
oldhand = getvect(0x1c);
/* clear enable flag */
enab = 0;
start = 0;
/* install new vector */
setvect(0x1c, shand);
/* set up interprocess communications area */
nsamp = 0;
bufp = databuf;
port = 0x279; /* address of printer status register */
cprintf("Sampling at %fHz (= %fms)....",
1193180.0 / (float)count, (float)count / 1193.18);
/* reprogram timer chip */
program_timer(0, count);
/* enable sampling */
enab = 1;
/* wait until sampling is completed */
while (enab) ;
/* restore standard timing value */
program_timer(0, 0);
/* reinstall old handler vector */
setvect(0x1c, oldhand);
cprintf(" completed.\r\n");
}
void main()
{
unsigned i;
/* allocate memory */
databuf = calloc(MAXSAMPLE, sizeof(byte));
assert (databuf != NULL);
cprintf("Press when ready to swipe card:");
getchar();
sample_data(12); /* This works out to about a 100kHz sampling rate */
cprintf("Sampling completed, %u samples total.\r\n", nsamp);
cprintf("Press to dump data.\r\n\r\n");
getchar();
/* dump data to stdout */
for (i=0; i