Microsoft Windows 95 on IBM ThinkPad Systems ============================================ Version 2.12 February 27th, 1996 This document contains information which assist you in using Microsoft** Windows** 95 operating system on IBM* ThinkPad systems. * Trademark of IBM Corporation ** Trademark of Microsoft Corporation IBM Personal Computer Company ----------------------------------------------------------------------- Table of Contents ================= 1. Before installing Windows 95 1.1. How to get the updated software from IBM 1.2. System program update 1.3. Backing up your software and data 1.4. Removing preinstalled software 1.5. Windows 95 setup disk for ThinkPad 1.6. Before installing Windows 95 2. ThinkPad 755C/Cs and systems 2.1. Install and setup Windows 95 on ThinkPad 2.2. Known limitations with Windows 95 3. ThinkPad 360/355 Family and 370C systems 3.1. Install and setup Windows 95 on ThinkPad 3.2. Known limitations with Windows 95 4. ThinkPad 340CSE systems 4.1. Install and setup Windows 95 on ThinkPad 4.2. Known limitations with Windows 95 5. ThinkPad 345C/CS systems 5.1. Install and setup Windows 95 on ThinkPad 5.2. Known limitations with Windows 95 6. ThinkPad 755CE/CSE/CX/CD/CV/CDV systems 7. ThinkPad 760C/CD systems 8. ThinkPad 701C/CS system 8.1. Install and setup Windows 95 on ThinkPad 8.2. Known limitations with Windows 95 9. ThinkPad 365 systems 9.1. Install and setup Windows 95 on ThinkPad 9.2. Known limitations with Windows 95 10. ThinkPad 530Cs systems 10.1. Install and setup Windows 95 on ThinkPad 10.2. Known limitations with Windows 95 11. System independent information 11.1. Suspend command on Start menu 11.2. PCMCIA function limitations 11.3. PCMCIA network adapter card compatibility in Dock II 11.4. PCMCIA support software setup 11.5. ThinkPad Docking control utility 11.6. ThinkPad Dock II docking station 12. Other ThinkPad systems 12.1. ThinkPad 750 systems 12.2. ThinkPad 340 system 12.3. ThinkPad 230Cs system 12.4. Other ThinkPad systems ----------------------------------------------------------------------- 1. Before installing Windows 95 ------------------------------- 1.1. How to get the updated software from IBM --------------------------------------------- Before you install Windows 95 on your ThinkPad, you may need to get some updated software from IBM or Microsoft. IBM PC Company is providing the updated software through several channels as follows. It is suggested to get the latest software from those channels so that you can set up Windows 95 on your ThinkPad systems with the information described in this document. The home page for IBM PC Company file library index is; http://www.pc.ibm.com/files.html Select "IBM Portables, Notebooks, Laptops Files" to find the necessary software. The IBM PC Company FTP server address for mobile product software fixes and patches is; ftp.pcco.ibm.com/pub/mobiles Join CompuServe ThinkPad Forum (GO THINKPAD) and download the necessary software from the library. Use a terminal emulation software and modem to connect the IBM PC Company BBS in the US. The phone number is; 919-517-0001. Go to Nifty-Serve FIBMJ Forum (GO FIBMJ or library #20) and get the necessary software (Japanese software only). Go to WIN95.CC Forum (Library #5)and get the necessary software (Japanese software only). If you cannot get the updated software from either one, please contact your IBM representative, or contact IBM HelpCenter (1-800- 772-2227 in the US) for more information. 1.2. System program update (Flash BIOS update) ---------------------------------------------- Before you install Windows 95, you are strongly recommended to get the following version of ThinkPad System Program Service Diskette and to update your flash BIOS. Otherwise, Windows 95 may not run as explained in this document. You need to follow the instructions provided by the system program service diskette very carefully to update your flash BIOS program. Your system could be damaged by incorrect operations during this system program update. --------------------------------------------------------- 1. You need to update the flash BIOS prior to install Windows 95 on your ThinkPad. In case you have already installed Windows 95 and update the flash BIOS later, you may need to run "Add hardware Wizard" of Windows 95 once again. If some problem still persists, it is recommended to reinstall Windows 95 after the flash BIOS update. 2. The preview program version of Windows 95 beta and earlier have a problem with IBM ThinkPad System Program Service Diskettes. You MUST turn on the write-protect switch of your ThinkPad System Service Diskette right after you create the diskette from its source file. If you don't, Windows 95 could damage the diskette when you write some data on it, or use "DIR" command against it. In this case, the diskette no longer works as a system service diskette and you need to recreate a diskette from the source diskette image. The commercial release of Windows 95 doesn't have this defect. --------------------------------------------------------------------- ThinkPad 750 Family - ThinkPad 355/360/750/755C/755Cs Family System Program Service Diskette version 1.41 or later ThinkPad 755C/Cs - ThinkPad 355/360/750/755C/755Cs Family System and 360/355 Family Program Service Diskette version 1.40 or later. ThinkPad 755CE/CSE - ThinkPad 755 Family System Program Service 755CD/CV Diskette version 1.40 or later. 755CX/CDV ThinkPad 760C/CD - ThinkPad 760 Family System Program Service Diskette version 1.00 or later. ThinkPad 701C/CS - ThinkPad 701 System Disk version 3M or later. ThinkPad 340CSE/ - ThinkPad 340CSE/370C/345 Family System Program 345C/CS and 370C Service Diskette version 1.40 or later. Note 1: IBM is testing the following ThinkPad systems with Windows 95 and APM (Advanced Power Management) BIOS 1.1 and PnP (Plug and Play) BIOS 1.0a are supported on these systems. - ThinkPad 755C/Cs - ThinkPad 360/355 Family (*1) - ThinkPad 755CE/CSE/CD/CX/CV/CDV - ThinkPad 760C/CD - Thinkpad 365 - ThinkPad 340CSE (*1) - ThinkPad 345C/CS (*1) - ThinkPad 370C - ThinkPad 701C/CS (*1) - ThinkPad 530CS (*1) Models already passed the Windows 95 logo testing at Microsoft and are eligible to get the logo. IBM is working on other models above for the logo. 2. IBM is testing the following ThinkPad systems with Windows 95 but only APM BIOS 1.0 is supported. No PnP BIOS support is available on these systems. - ThinkPad 750 Family - ThinkPad 340 (Monochrome display system) - ThinkPad 230Cs 3: IBM is not testing any other ThinkPad systems with Windows 95. Windows 95 may run on those ThinkPad systems but IBM does not plan to test Windows 95 on those systems. 1.3. Backing up your software and data -------------------------------------- IBM recommends that you use a diskette backup program on your system to create recovery diskettes of the preinstalled operating systems, device drivers and applications. In addition, IBM recommends that you back up all data files to disk before installing Windows 95. 1.4. Removing preinstalled software ----------------------------------- If you purchase a SelectaSystem model and are using OS/2 Warp version 3, Windows 95 cannot be installed with OS/2 Warp dual boot configuration in the SelectaSystem. Therefore, if you wish to install Windows 95, OS/2 Warp should be removed from your system along with all the preinstalled OS/2 applications. "Uninstall OS/2" icon is available for you in "OS/2 Warp" program group folder on your Windows desktop screen of SelectaSystem configuration. If you wish to continue using OS/2 Warp with Windows 95, you need to use OS/2 Warp Boot Manager. For more information, refer to Windows 95 SETUP.TXT file. It can be found on the Windows 95 disk 1 or the Windows 95 CD-ROM. If you plan to install, or have already installed Windows 95 over the following ThinkPad systems with factory preinstalled software, you may encounter "Windows 95 Explorer Fault". - ThinkPad 755C/Cs - ThinkPad 360/355 Family - ThinkPad 755CE/CSE/CD - ThinkPad 340CSE - ThinkPad 370C - ThinkPad 701C/CS If you have this problem, or to avoid this problem, please take the following steps. 1. Edit your WIN.INI file located under C:\WINDOWS subdirectory. For example, type "E C:\WINDOWS\WIN.INI" and press ENTER from DOS command prompt. 2. In [windows] section, find the "load=" statement. Remove STRTSCR.EXE from the "load=" statement as follows. Your original WIN.INI --------------------- [windows] : load=C:\SCREENS\STRTSCR.EXE C:\THINKPAD\FUELWIN.EXE : Remove STRTSCR.EXE ------------------ [windows] : load=C:\THINKPAD\FUELWIN.EXE : 3. After you remove STRTSCR.EXE, you will no longer see the ThinkPad Welcome screen. If you have already removed this screen, nothing will be changed by removing STRTSCR.EXE. 1.5. Windows 95 setup disk for ThinkPad --------------------------------------- To assist the Windows 95 installation, "Windows 95 setup disk" is available through the support network mentioned in "Section 1.1 - How to get the updated software from IBM". The Windows 95 setup disk supports the following ThinkPad systems. Before using the setup disk, you should review README first. - ThinkPad 755C/Cs - ThinkPad 701C/CS - ThinkPad 360/355 Family and 370C - ThinkPad 340CSE 1.6. Before installing Windows 95 --------------------------------- Before you install Windows 95 operating system, it is recommended to review the information which is particular to your ThinkPad model. This would minimize your effort to set up Windows 95 on your ThinkPad system. ----------------------------------------------------------------------- 2. ThinkPad 755C/Cs systems --------------------------- 2.1. Install and setup Windows 95 on ThinkPad --------------------------------------------- 2.1.0. Before you proceed ------------------------- Again, you are strongly recommended to get the latest system program service diskette and update your system BIOS before installing Windows 95 on your system. You need to get the following updated software before installing Windows 95 on your ThinkPad. Necessary: - ThinkPad 750/360/755 Family System Program Service Diskette version 1.41 or later - ThinkPad Audio Feature Diskette version 1.40 or later Recommended: - ThinkPad Utility Diskette No.1 version 3.10 or later - ThinkPad Video Feature Diskette version 1.33 or later 2.1.1. During Windows 95 installation ------------------------------------- You may encounter "Unknown Hardware Found" message when you install Windows 95. In this case, select "Do not install a driver (Windows will not prompt you again)". By doing this, you will see "Unknown Device" under "Other devices" in Windows 95 Device Manager. This "Unknown Device" is ThinkPad Audio device. If you want to see this device name in Device Manager, refer to "Unknown Hardware" problem in Section 2.2. 2.1.2. Video device drivers --------------------------- The video device driver for ThinkPad 755C/Cs systems is included in Windows 95 and it is automatically installed by Windows 95 Setup program. You don't need ThinkPad Windows video device driver any longer but still need to install ThinkPad VESA video driver. The following procedure enables Windows 95 video device driver functions. --------------------------------------------------------- The following procedure is NOT applicable on ThinkPad 755CE/CSE/CD/ CX/CV/CDV, 345C/CS and 760C/CD systems. --------------------------------------------------------------------- 1. Check your CONFIG.SYS file and look for the following statement. : DEVICE=C:\IBMVESA\VESA.EXE : (Note: The directory "C:\IBMVESA" could be different if you have installed ThinkPad DOS video device driver into a different subdirectory.) If you find the statement, your system is already set up for Windows 95 video device driver for ThinkPad. If not, go to the next step. 2. Obtain ThinkPad Video feature diskette. (The latest version as of 6/1/95 is 1.33) and insert it into the diskette drive. 3. Go to the DOS command prompt. Then, type A:VINSTALL and press Enter. The supported display list appears. 4. Using the Arrow keys, highlight the display type which you use with your ThinkPad, and press Enter. 5. Follow the instructions on the screen to save your display selection; then press F3 to exit the menu. 6. Remove the diskette from the diskette drive; then restart the system. The ThinkPad is now ready to work with Windows 95 video device driver. 1. After installing or set up Windows 95 on your ThinkPad; click "My Computer". 2. Click "Control Panel"; Click "Display"; Click on "Setting" tab. 3. Click "Change Display Type..." button. 4. Make sure that Adapter Type is "Western Digital". 5. Close "Change Display Type" windows; verify that "256 Color" can be selected in "Color palette". 2.1.3. ThinkPad Features Program -------------------------------- The ThinkPad Features Program for Windows works on Windows 95. If you install Windows 95 over a DOS/Windows 3.x system on which you have already installed ThinkPad Features Program, it is migrated into "Start Menu" automatically. Click "Start"; click "Programs"; click "ThinkPad"; then click "ThinkPad Features" to start the program. If you install Windows 95 on a blank hard disk or you haven't installed ThinkPad Features Program, follow the instructions of "ThinkPad Features Program - Installing for Windows" in the ThinkPad User's Guide. 2.1.4. PCMCIA Device driver --------------------------- Windows 95 comes with the integrated PCMCIA support. To use the Windows 95 PCMCIA support functions, refer to the Windows 95 documentation or on-line help. If you want to use ThinkPad PC Card Director (or EasyPlaying), you still can use ThinkPad DOS PCMCIA device drivers. To install ThinkPad PCMCIA device drivers, follow the instructions of "Installing the PCMCIA drivers - Installing for DOS" in the ThinkPad User's Guide. --------------------------------------------------------- The Windows 95 installation program doesn't enable its own 32bit PCMCIA support automatically. If you already have a ThinkPad system with ThinkPad DOS/Windows PCMCIA software and install Windows 95 on the system, the Windows 95 installation program keeps the ThinkPad PCMCIA support software and you can keep using it. However, the Windows 95 plug and play functions of its own PCMCIA support cannot be used with ThinkPad PCMCIA support software. For more detail about PCMCIA support software setup, refer to "Section 11.4. PCMCIA support software setup. --------------------------------------------------------------------- 2.1.5. Audio Support Software ----------------------------- The ThinkPad Audio Support Software for Windows works on Windows 95. If you install Windows 95 over a DOS/Windows 3.x system on which you have already installed ThinkPad Audio Support Software, it is migrated into "Start Menu" automatically. Click "Start"; click "Programs"; then click "Audio" to select the ThinkPad audio program which you use. If you install Windows 95 on a blank hard disk or you haven't installed ThinkPad Features Program, follow the instructions of "ThinkPad Features Program - Installing for Windows" in the ThinkPad User's Guide. You also need to review the following information. --------------------------------------------------------- Before installing ThinkPad Audio support software, you have to verify that your ThinkPad has CONFIG.SYS file in the root directory of boot drive. Also you might need to install Audio support software twice to get it work correctly. ThinkPad Audio Support Software setup makes several program icons to use ThinkPad audio functions. The "Sound Recorder" icon, which works fine under Windows 3.1, is not set up correctly under Windows 95 because the program name of Windows sound record utility is changed. To setup "Sound Recorder" icon; 1. Verify that you have successfully installed or migrated ThinkPad Audio Support Software onto Windows. - Click "Start"; click "Programs"; then click "Audio" - "Audio Control", "Media Player", "Sound Recorder" and "Read Me" programs should be visible. If not, you need to reinstall ThinkPad Audio Support Software. 2. Click "Start"; click "Settings"; then click "Taskbar..." 3. Click on "Start Menu Programs" tab. 4. Click "Advanced..." button. 5. Click "+" mark of "Programs" in the hierarchy window located left- hand side; then click "Audio". 6. Highlight "Sound Recorder" in the content window located right- hand side; click "File" menu; then click "Properties". 7. Click on "Shortcut" tab; and change "Target" program name from "SOUNDREC.EXE" to "C:\WINDOWS\SNDREC32.EXE". (C:\WINDOWS could be different depending on the subdirectory in which you installed Windows 95.) 8. Click "OK"; now you can use "Sound Recorder" under Windows 95. Note: This limitation will be fixed in the next release of ThinkPad Audio feature program. --------------------------------------------------------------------- 2.2. Known limitations with Windows 95 -------------------------------------- o Token-Ring Credit Card Adapter problem When you use IBM Token-Ring 16/4 Credit Card Adapter II (Part Number 0933931) with Windows 95 PCMCIA support software, the card may not be enabled correctly. Most 755C/Cs products don't have this problem. IBM Token-Ring 16/4 Credit Card Adapter and IBM Token-Ring Auto 16/4 Credit Adapter III (Part Number 04H6922) don't have this problem. The updated driver will be provided from Microsoft drivers library. o Horizontal stripe appears with mouse pointer on external CRT When you attach a high resolution external CRT monitor and switch between a MS-DOS full screen session and Windows 95 desktop, you may observe a horizontal stripe with the mouse pointer. If this happens, take the following steps. 1. Click "My Computer" 2. Click "Control Panel" 3. Click "System" 4. Click on "Performance" tab 5. Click "Graphics..." button 6. Move the slider of "Hardware acceleration" left one notch 7. You will be prompted to restart the system Upon next system boot, the horizontal stripe should disappear. o "Unknown Hardware" problem If you want to fix this problem, you first need to modify a Win95 information file in a hidden directory. If you are not familiar with Windows 95 or you are a non-experienced PC / Windows user, it's not recommended to do the following. Unexpected results may occur if you cannot follow the instructions correctly. 1. Go to MS-DOS Prompt 2. Type "CD INF" and press Enter to go to the subdirectory C:\WINDOWS\INF. (Note that C:\WINDOWS\INF is a hidden directory) 3. Back up NODRIVER.INF. Type "COPY NODRIVER.INF NODRIVER.BAK". These *.INF files are very important for Windows 95 Device Manager and you need to save the original one. 4. Edit NODRIVER.INF. Type "EDIT NODRIVER.INF" and press Enter. 5. Search [Manufacturer] section; Find the following statement. %IBMMfg%=IBM If you can find it, go to the next step. Otherwise, add this statement in [Manufacturer] section. 6. Search [IBM] section; if you don't find it, add [IBM] section somewhere between [Manufacturer] and [NODRIVER] section; find the following statement. %*IBM0040.DeviceDesc%=NODRIVER,*IBM0040 If you cannot find it, simply add this statement in [IBM] section. Otherwise, go to the next step. 7. Search [String] section; find 'IBMMfg="IBM"' statement; after this line, find the following statement. *IBM0040.DeviceDesc="xxxxxx" (xxxxxx is some device name) If you find it, change it to as follows. *IBM0040.DeviceDesc="ThinkPad Audio Device" 8. Save the modified NODRIVER.INF file. And exit MS-DOS prompt. Next, you need to remove "Unknown Device" (or "Mwave DSP") from Device Manager. Then need to refresh the hardware structure. 9. Click "My Computer" 10. Click "Control Panel" 11. Click "System" 12. Click on "Device Manager" tab 13. Click "+" mark of "Other devices"; you see "Unknown Device" (or "Mwave DSP processor"). 14. Click on "Unknown Device" (or "Mwave DSP") and click "Remove" button; click "OK" to confirm. 15. Click "Refresh" button; Windows 95 will restructure the device tree in "Device Manager" and you now should see "ThinkPad Audio Device" under "Other detected devices". --------------------------------------------------------- If you encounter any unexpected results by doing the above, you might have failed to modify your NODRIVER.INF file correctly. You should recover your original NODRIVER.INF from NODRIVER.BAK which you've saved. Rename NODRIVER.BAK to NODRIVER.INF and do the above steps again, if desired. --------------------------------------------------------------------- ----------------------------------------------------------------------- 3. ThinkPad 360/355 Family and 370C systems ------------------------------------------- 3.1. Install and setup Windows 95 on ThinkPad --------------------------------------------- 3.1.0. Before you proceed ------------------------- Again, you are strongly recommended to get the latest system program service diskette and update your system BIOS before installing Windows 95 on your system. You need to get the following updated software before installing Windows 95 on your ThinkPad. Necessary: o ThinkPad 360/355 Family - ThinkPad 355/360/750/755 Family System Program Service Diskette version 1.41 or later o ThinkPad 370C - ThinkPad 340CSE/370/345 System Program Service Diskette version 1.40 or later Recommended: - ThinkPad Utility Diskette No.1 version 3.10 or later - ThinkPad Video Feature Diskette version 1.33 or later - ThinkPad Audio Feature Diskette version 1.40 or later (Only if your system has an optional audio device. Refer to Section 2.1.5 for audio support software setup information.) 3.1.1. Video device drivers --------------------------- The video device driver for ThinkPad 360/355/370 systems is included in Windows 95 and it is automatically installed by Windows 95 Setup program. You don't need ThinkPad Windows video device driver any longer but still need to install ThinkPad VESA video driver. The following procedure enables Windows 95 video device driver functions. 1. Check your CONFIG.SYS file and look for the following statement. : DEVICE=C:\IBMVESA\VESA.EXE : (Note: The directory "C:\IBMVESA" could be different if you have installed ThinkPad DOS video device driver into a different subdirectory.) If you find the statement, your system is already set up for Windows 95 video device driver for ThinkPad. If not, go to the next step. 2. Have ThinkPad Video feature diskette. (The latest version as of 6/1/95 is 1.33) and insert it into the diskette drive. 3. Go to the DOS command prompt. Then, type A:VINSTALL and press Enter. The supported display list appears. 4. Using the Arrow keys, highlight the display type which you use with your ThinkPad, and press Enter. 5. Follow the instructions on the screen to save your display selection; then press F3 to exit the menu. 6. Remove the diskette from the diskette drive; then restart the system. The ThinkPad is now ready to work with Windows 95 video device driver. 1. After installing or set up Windows 95 on your ThinkPad; click "My Computer". 2. Click "Control Panel"; Click "Display"; Click on "Setting" tab. 3. Click "Change Display Type..." button. 4. Make sure that Adapter Type is "Western Digital". 5. Close "Change Display Type" windows; verify that "256 Color" can be selected in "Color palette". 3.1.2. ThinkPad Features Program -------------------------------- The ThinkPad Features Program for Windows works on Windows 95. If you install Windows 95 over a DOS/Windows 3.x system on which you have already installed ThinkPad Features Program, it is migrated into "Start Menu" automatically. Click "Start"; click "Programs"; click "ThinkPad"; then click "ThinkPad Features" to start the program. If you install Windows 95 on a blank hard disk or you haven't installed ThinkPad Features Program, follow the instructions of "ThinkPad Features Program - Installing for Windows" in the ThinkPad User's Guide. 3.1.3. PCMCIA Device driver --------------------------- Windows 95 comes with the integrated PCMCIA support. To use the Windows 95 PCMCIA support functions, refer to the Windows 95 documentation or on-line help. If you want to use ThinkPad PC Card Director (or EasyPlaying), you still can use ThinkPad DOS PCMCIA device drivers. To install ThinkPad PCMCIA device drivers, follow the instructions of "Installing the PCMCIA drivers - Installing for DOS" in the ThinkPad User's Guide. --------------------------------------------------------- The Windows 95 installation program doesn't enable its own 32bit PCMCIA support automatically. If you already have a ThinkPad system with ThinkPad DOS/Windows PCMCIA software and install Windows 95 on the system, the Windows 95 installation program keeps the ThinkPad PCMCIA support software and you can keep using it. However, the Windows 95 plug and play functions of its own PCMCIA support cannot be used with ThinkPad PCMCIA support software. For more detail about PCMCIA support software setup, refer to "Section 11.4. PCMCIA support software setup. --------------------------------------------------------------------- 3.2. Known limitations with Windows 95 -------------------------------------- o Horizontal stripe appears with mouse pointer on external CRT When you attach a high resolution external CRT monitor and switch between a MS-DOS full screen session and Windows 95 desktop, you may observe a horizontal stripe with the mouse pointer. If this happens, take the following steps. 1. Click "My Computer" 2. Click "Control Panel" 3. Click "System" 4. Click on "Performance" tab 5. Click "Graphics..." button 6. Move the slider of "Hardware acceleration" left one notch 7. You will be prompted to restart the system Upon next system boot, the horizontal stripe should disappear. o Token-Ring Credit Card Adapter problem When you use IBM Token-Ring 16/4 Credit Card Adapter II (Part Number 0933931) with Windows 95 PCMCIA support software, the card may not be enabled correctly. Most ThinkPad 355/360 products don't have this problem. ThinkPad 370C system doesn't have this problem. IBM Token-Ring 16/4 Credit Card Adapter and IBM Token-Ring Auto 16/4 Credit Adapter III (Part Number 04H6922) don't have this problem. The updated driver will be provided from Microsoft drivers library. ----------------------------------------------------------------------- 4. ThinkPad 340CSE systems -------------------------- 4.1. Install and setup Windows 95 on ThinkPad --------------------------------------------- 4.1.0. Before you proceed ------------------------- Again, you are strongly recommended to get the latest system program service diskette and update your system BIOS before installing Windows 95 on your system. You need to get the following updated software before installing Windows 95 on your ThinkPad. Necessary: - ThinkPad 340CSE/370/345 System Program Service Diskette version 1.40 or later Recommended: - ThinkPad Utility Diskette No.1 version 3.10 or later --------------------------------------------------------- If you plan to install Windows 95 on a blank hard disk or your system has only DOS without the DOS mouse driver, please do one of the following. 1. Install DOS mouse driver before installing Windows 95. You can create IBM PC-DOS diskettes using the diskette backup program that is preinstalled on your computer. - or - 2. Follow the instructions below. a. Start Easy-Setup - Turn off the computer; then remove any diskette from the diskette drive. - Press and hold F1; then turn on the computer. Hold F1 until the Easy-Setup menu appears. b. Disable "TrackPoint" temporarily. - Select "Config"; then select "Keyboard" - Select "Disable" for "Track Point" - End Easy-Setup c. Use an external mouse, if available. Restart the computer. d. Install Windows 95 without the TrackPoint pointing device. e. After the installation is completed. Enable TrackPoint device again by Easy-Setup. - Turn off the computer; then remove any diskette from the diskette drive. - Press and hold F1; then turn on the computer. Hold F1 until the Easy-Setup menu appears. - Select "Config"; then select "Keyboard" - Select "Enable" for "Track Point" Then TrackPoint pointing device is now enabled, and you can use it with Windows 95. --------------------------------------------------------------------- 4.1.1. Video device drivers --------------------------- The video device driver for ThinkPad 340CSE systems is included in Windows 95 and it is automatically installed by Windows 95 Setup program. You don't need ThinkPad Windows video device driver any longer. 1. After installing or set up Windows 95 on your ThinkPad; click "My Computer". 2. Click "Control Panel"; Click "Display"; Click on "Setting" tab. 3. Click "Change Display Type..." button. 4. Make sure that Adapter Type is "Cirrus Logic". 4.1.2. ThinkPad Features Program -------------------------------- The ThinkPad Features Program for Windows works on Windows 95. If you install Windows 95 over a DOS/Windows 3.x system on which you have already installed ThinkPad Features Program, it is migrated into "Start Menu" automatically. Click "Start"; click "Programs"; click "ThinkPad"; then click "ThinkPad Features" to start the program. If you install Windows 95 on a blank hard disk or you haven't installed ThinkPad Features Program, follow the instructions of "ThinkPad Features Program - Installing for Windows" in the ThinkPad User's Guide. 4.1.3. PCMCIA Device driver --------------------------- Windows 95 comes with the integrated PCMCIA support. To use the Windows 95 PCMCIA support functions, refer to the Windows 95 documentation or on-line help. If you want to use ThinkPad PC Card Director (or EasyPlaying), you still can use ThinkPad DOS PCMCIA device drivers. To install ThinkPad PCMCIA device drivers, follow the instructions of "Installing the PCMCIA drivers - Installing for DOS" in the ThinkPad User's Guide. --------------------------------------------------------- The Windows 95 installation program doesn't enable its own 32bit PCMCIA support automatically. If you already have a ThinkPad system with ThinkPad DOS/Windows PCMCIA software and install Windows 95 on the system, the Windows 95 installation program keeps the ThinkPad PCMCIA support software and you can keep using it. However, the Windows 95 plug and play functions of its own PCMCIA support cannot be used with ThinkPad PCMCIA support software. For more detail about PCMCIA support software setup, refer to "Section 11.4. PCMCIA support software setup. --------------------------------------------------------------------- 4.2. Known limitations with Windows 95 -------------------------------------- o Windows 95 logo screen becomes brown Upon Windows 95 boot, its logo screen background becomes brown. This is normal and everything works fine after Windows 95 desktop screen appears. o Using TrackPoint during disk compression When you compress a drive from "Compression" tab in "Drive" property sheet of Windows 95, or Windows 95 compression utility, do not use the ThinkPad TrackPoint pointing device. If you touch the TrackPoint, the compression program stops and the system hangs up. If this happens, disable the TrackPoint by ThinkPad Features program, and retry the compression. ----------------------------------------------------------------------- 5. ThinkPad 345C/CS systems --------------------------- 5.1. Install and setup Windows 95 on ThinkPad --------------------------------------------- 5.1.0. Before you proceed ------------------------- Again, you are strongly recommended to get the latest system program service diskette and update your system BIOS before installing Windows 95 on your system. You need to get the following updated software before installing Windows 95 on your ThinkPad. Necessary: - None Recommended: - ThinkPad 340CSE/370/345 System Program Service Diskette version 1.40 or later - ThinkPad Utility Diskette No.1 version 3.10 or later --------------------------------------------------------- If you plan to install Windows 95 on a blank hard disk or your system has only DOS without the DOS mouse driver, please do one of the following. 1. Install DOS mouse driver before installing Windows 95. You can create IBM PC-DOS diskettes using the diskette backup program that is preinstalled on your computer. - or - 2. Follow the instructions below. a. Start the computer from a bootable diskette. You can create a DOS bootable diskette using a diskette backup program that is preinstalled on your computer. The diskette name is "DOS diskette #1". b. Insert the ThinkPad utility diskette #1 into the diskette drive. You can create the ThinkPad Utility diskette #1 using a diskette backup program that is preinstalled on your computer. c. Type A:PS2 TPO D; then press Enter. The TrackPoint pointing device will be temporarily disabled. Use an external mouse, if available. d. Remove the diskette; then restart the computer. e. Install Windows 95 without the TrackPoint pointing device. f. After the installation is completed, restart Windows 95; then go to the DOS command prompt. g. Insert the ThinkPad Utility diskette into the diskette drive. h. Type A:PS2 TPO E; then press Enter. i. Remove the diskette; then restart the computer. Then TrackPoint pointing device is now enabled, and you can use it with Windows 95. --------------------------------------------------------------------- 5.1.1. Video device drivers --------------------------- The video device driver for ThinkPad 345 systems is included in Windows 95 and it is automatically installed by Windows 95 Setup program. You don't need ThinkPad Windows video device driver any longer. 1. After installing or set up Windows 95 on your ThinkPad; click "My Computer". 2. Click "Control Panel"; Click "Display"; Click on "Setting" tab. 3. Click "Change Display Type..." button. 4. Make sure that Adapter Type is "Western Digital". 5. Close "Change Display Type" windows; verify that "256 Color" can be selected in "Color palette". 5.1.2. ThinkPad Features Program -------------------------------- The ThinkPad Features Program for Windows works on Windows 95. If you install Windows 95 over a DOS/Windows 3.x system on which you have already installed ThinkPad Features Program, it is migrated into "Start Menu" automatically. Click "Start"; click "Programs"; click "ThinkPad"; then click "ThinkPad Features" to start the program. If you install Windows 95 on a blank hard disk or you haven't installed ThinkPad Features Program, follow the instructions of "ThinkPad Features Program - Installing for Windows" in the ThinkPad User's Guide. 5.1.3. PCMCIA Device driver --------------------------- Windows 95 comes with the integrated PCMCIA support. To use the Windows 95 PCMCIA support functions, refer to the Windows 95 documentation or on-line help. If you want to use ThinkPad PC Card Director (or EasyPlaying), you still can use ThinkPad DOS PCMCIA device drivers. To install ThinkPad PCMCIA device drivers, follow the instructions of "Installing the PCMCIA drivers - Installing for DOS" in the ThinkPad User's Guide. --------------------------------------------------------- The Windows 95 installation program doesn't enable its own 32bit PCMCIA support automatically. If you already have a ThinkPad system with ThinkPad DOS/Windows PCMCIA software and install Windows 95 on the system, the Windows 95 installation program keeps the ThinkPad PCMCIA support software and you can keep using it. However, the Windows 95 plug and play functions of its own PCMCIA support cannot be used with ThinkPad PCMCIA support software. For more detail about PCMCIA support software setup, refer to "Section 11.4. PCMCIA support software setup. --------------------------------------------------------------------- 5.2. Known limitations with Windows 95 -------------------------------------- o Horizontal stripe appears with mouse pointer on external CRT When you attach a high resolution external CRT monitor and switch between a MS-DOS full screen session and Windows 95 desktop, you may observe a horizontal stripe with the mouse pointer. If this happens, take the following steps. 1. Click "My Computer" 2. Click "Control Panel" 3. Click "System" 4. Click on "Performance" tab 5. Click "Graphics..." button 6. Move the slider of "Hardware acceleration" left one notch 7. You will be prompted to restart the system Upon next system boot, the horizontal stripe should disappear. o Using TrackPoint during disk compression When you compress a drive from "Compression" tab in "Drive" property sheet of Windows 95, or Windows 95 compression utility do not use the ThinkPad TrackPoint pointing device. If you touch the TrackPoint, the compression program stops and the system hangs up. If this happens, disable the TrackPoint by ThinkPad Features program, and retry the compression. ----------------------------------------------------------------------- 6. ThinkPad 755CE/CSE/CD/CX/CV/CDV systems ------------------------------------------ Please see separate 755EW95.TXT for installation instructions. ------------------------------------------------------------------------ 7. ThinkPad 760C/CD systems --------------------------- Please see separate 760W95.TXT for installation instructions. ----------------------------------------------------------------------- 8. ThinkPad 701C/CS systems -------------------------- 8.1. Install and setup Windows 95 on ThinkPad --------------------------------------------- 8.1.0. Before you proceed ------------------------- Again, you are strongly recommended to get the latest system program service diskette and update your system BIOS before installing Windows 95 on your system. You need to get the following updated software before installing Windows 95 on your ThinkPad. Necessary: - ThinkPad 701 System Disk version 3M or later Recommended: - None The Windows 95 device drivers for ThinkPad 701C are included in Windows 95. When you install Windows 95 operating system on ThinkPad 701C, the device drivers are installed automatically. 8.1.1. PCMCIA Device driver --------------------------- Windows 95 comes with the integrated PCMCIA support. To use the Windows 95 PCMCIA support functions, refer to the Windows 95 documentation or on-line help. If you want to use ThinkPad PC Card Director (or EasyPlaying), you still can use ThinkPad DOS PCMCIA device drivers. To install ThinkPad PCMCIA device drivers, follow the instructions of "Installing the PCMCIA drivers - Installing for DOS" in the ThinkPad User's Guide. --------------------------------------------------------- The Windows 95 installation program doesn't enable its own 32bit PCMCIA support automatically. If you already have a ThinkPad system with ThinkPad DOS/Windows PCMCIA software and install Windows 95 on the system, the Windows 95 installation program keeps the ThinkPad PCMCIA support software and you can keep using it. However, the Windows 95 plug and play functions of its own PCMCIA support cannot be used with ThinkPad PCMCIA support software. For more detail about PCMCIA support software setup, refer to "Section 11.4. PCMCIA support software setup. --------------------------------------------------------------------- 8.2. Known limitations with Windows 95 -------------------------------------- o Auto suspend not working when docked If you dock the ThinkPad 701, the auto suspend timer doesn't work due to a Adapter SCSI driver problem in Windows 95. o PCMCIA power management limitations Windows 95 doesn't turn off PC cards before suspend. This would cause shorter suspend time due to power drain. To turn off PC cards during suspend, do one of the following. - With ThinkPad 701C System Disk version 3M: Press Fn+F11 followed immediately by Fn+Enter to set a flag forcing BIOS to suspend the PCMCIA even if there is a powered card in the slot (with PCMCIA power setting = Auto in Configuration Utility). This should work for modem cards. - Use IBM PC Card Director PCMCIA software ----------------------------------------------------------------------- 9. ThinkPad 365 systems ----------------------- 9.1. Install and setup Windows 95 on ThinkPad --------------------------------------------- 9.1.0. Before you proceed ------------------------- You don't need to get any updated software for ThinkPad 365 systems before installing Windows 95. However, you should create device driver and utility diskettes that are unique to ThinkPad 365 using "Diskette Factory" program so that you can reinstall the drivers and utilities if needed. For instructions on how to make back up copies, see ThinkPad 365 User's Guide. The device drivers are listed under the following names in the "Diskette Factory" program. - "ThinkPad Utility Diskette" This consists of EPP3NS.EXE, SUPASS.EXE, PHDISK.EXE and README.DOC. - "ThinkPad Infrared Features" This consists of the Infrared driver. - "ThinkPad CD-ROM" This consists of the CD-ROM driver. If your ThinkPad 365 system is a Windows 95 preinstalled model, these drivers are already installed on your system. 9.1.1. PCMCIA Device driver --------------------------- Windows 95 comes with the integrated PCMCIA support. To use the Windows 95 PCMCIA support functions, refer to the Windows 95 documentation or on-line help. If you want to use ThinkPad PC Card Director (or EasyPlaying), you still can use ThinkPad DOS PCMCIA device drivers. To install ThinkPad PCMCIA device drivers, follow the instructions in ThinkPad 365 User's Guide. --------------------------------------------------------- The Windows 95 installation program doesn't enable its own 32bit PCMCIA support automatically. If you already have a ThinkPad system with ThinkPad DOS/Windows PCMCIA software and install Windows 95 on the system, the Windows 95 installation program keeps the ThinkPad PCMCIA support software and you can keep using it. However, the Windows 95 plug and play functions of its own PCMCIA support cannot be used with ThinkPad PCMCIA support software. For more detail about PCMCIA support software setup, refer to "Section 11.4. PCMCIA support software setup. --------------------------------------------------------------------- 9.1.2. Video Device driver --------------------------- If your system is a Windows 95 preinstalled model, it comes with the Chips & Technology Accelerator display adapter. If you need to install Windows 95 on your system, use the Chips & Technology Accelerator display adapter. To verify that the display driver is correctly installed: 1. Start Windows 95. 2. Open "My Computer". 3. Open "Control Panel" and open "Display"; then click on the setting tab. 4. Click on the "Change Display Type..." button. 5. Make sure that "Chips & Technology Accelerator" is shown as the selection; then click OK. 6. Select your screen parameters from the Color Palette and Desktop area; then click OK. 7. Follow the instructions on the screen. Windows 95 may prompt you to restart the computer to make the video driver change effective. 9.1.3. Audio Device driver --------------------------- If your system is a Windows 95 preinstalled model, it comes with the ESS ES1688 Plug and Play AudioDrive driver pre-configured with the option of "Use single mode DMA", already selected. If you need to install Windows 95 on the ThinkPad 365, you need to configure the ESS ES1688 AudioDrive driver with the option of "Use single mode DMA" selected, using the following procedure: 1. Go to "Control Panel". 2. Double click "Multimedia", then click "Advanced" in the "Multimedia properties" window. 3. Go to "Audio Devices" in the list of "Multimedia devices", then double click "Audio for ESS ES1688 Plug and Play AudioDrive". 4. Select "Settings". 5. Select "Use single mode DMA". 6. Restart Windows 95. The ESS ES1688 Audio device can be disabled and enabled either through the Device Manager in Windows 95, or the Setup screen in MS-DOS. To access the Setup screen, see "Using Setup". Disabling the ESS ES1688 Audio using the Setup screen releases the computer resources allocated for using the ESS ES1688 Audio. Disabling the ESS ES1688 Audio using the Device Manager in Windows 95 may not release the computer resources allocated for using the ESS ES1688 Audio. 9.1.4. Using Setup ------------------ To access the Setup screen in Windows 95, start the computer in MS- DOS mode. Press Ctrl and Alt keys together an while holding them down, press F11 key at the MS-DOS prompt. 9.1.5. ThinkPad Utility ----------------------- To install the "ThinkPad Utility for DOS": 1. Insert the "ThinkPad Utility diskette" into drive A:. 2. Go to DOS prompt. Type "A:\INSTALL". Press Enter. 3. Follow the instructions on the screen. The three utility files: EPP3NS.EXE, SUPASS.EXE, PHDISK.EXE and the system README.DOC files are copied into C:\THINKPAD sub-directory. 9.1.6. Infrared Device Driver ----------------------------- To install the "Infrared Device driver": 1. Insert the "ThinkPad Infrared Features" diskette into drive A:. 2. Go to DOS prompt. Type "A:\UINSTALL". Press Enter. 3. Follow the instructions on the screen and use the default "Target path" of C:\WINDOWS\, for installing the driver. 9.1.7. CD-ROM Device Driver --------------------------- To install the "ThinkPad CD-ROM Device driver": 1. Insert the "ThinkPad CD-ROM" diskette into drive A:. 2. Click "Start" on the Windows 95 desktop, then click "Run". 3. Type "A:\SETUP.EXE". Press Enter. 4. Select "Primary" I/O port address in the "I/O port select" screen. 5. Follow the instructions on the screen. 9.2. Known limitations with Windows 95 -------------------------------------- o Fax applications IBM recommends that you use the "FaxWorks" application program, preinstalled on your system, to send and receive fax messages. the "Microsoft Fax" program, located in the Accessories in Windows 95 may not work properly. ----------------------------------------------------------------------- 10. ThinkPad 530CS system (Available only in Japan) --------------------------------------------------- 10.1. Install and setup Windows 95 on ThinkPad ---------------------------------------------- 10.1.1. During Windows 95 installation -------------------------------------- You may encounter "Unknown Hardware Found" messages when you install Windows 95. In these cases, select "Do not install a driver (Windows will not prompt you again)". By doing this, you will see "Unknown Device"s under "Other devices" in Windows 95 Device Manager. After you complete all the device driver installation, "Unknown Device"s should disappear. --------------------------------------------------------- During the Windows 95 installation, you are asked if you want to make a startup diskette for emergency use. It is strongly recommended to attach the external floppy disk drive to ThinkPad 530CS when you install Windows 95. Without the floppy drive, you might experience an inactive period for about two minutes during Windows 95 installation. This is not a system hang. However, you need to attach the external floppy drive to avoid this symptom. --------------------------------------------------------------------- 10.1.2. Video device drivers ---------------------------- The video device driver for ThinkPad 530CS systems is included in Windows 95 and it is automatically installed by Windows 95 Setup program. You don't need ThinkPad Windows video device driver any longer. 1. After installing or set up Windows 95 on your ThinkPad; click "My Computer". 2. Click "Control Panel"; Click "Display"; Click on "Setting" tab. 3. Click "Change Display Type..." button. 4. Make sure that Adapter Type is "Cirrus Logic". 10.1.3. ThinkPad Features Program --------------------------------- The ThinkPad Features Program for Windows works on Windows 95. If you install Windows 95 over a DOS/Windows 3.x system on which you have already installed ThinkPad Features Program, it is migrated into "Start Menu" automatically. Click "Start"; click "Programs"; click "ThinkPad"; then click "ThinkPad Features" to start the program. If you install Windows 95 on a blank hard disk or you haven't installed ThinkPad Features Program, follow the instructions of "ThinkPad Features Program - Installing for Windows" in the ThinkPad User's Guide. 10.1.4. PCMCIA Device driver ---------------------------- Windows 95 comes with the integrated PCMCIA support. To use the Windows 95 PCMCIA support functions, refer to the Windows 95 documentation or on-line help. If you want to use ThinkPad PC Card Director (or EasyPlaying), you still can use ThinkPad DOS PCMCIA device drivers. To install ThinkPad PCMCIA device drivers, follow the instructions of "Installing the PCMCIA drivers - Installing for DOS" in the ThinkPad User's Guide. --------------------------------------------------------- The Windows 95 installation program doesn't enable its own 32bit PCMCIA support automatically. If you already have a ThinkPad system with ThinkPad DOS/Windows PCMCIA software and install Windows 95 on the system, the Windows 95 installation program keeps the ThinkPad PCMCIA support software and you can keep using it. However, the Windows 95 plug and play functions of its own PCMCIA support cannot be used with ThinkPad PCMCIA support software. For more detail about PCMCIA support software setup, refer to "Section 11.4. PCMCIA support software setup. --------------------------------------------------------------------- 10.1.5. Mwave support software ------------------------------ You need to have Mwave support software for "Windows 95" version 2.10 or later. Although Mwave support software for Windows version 2.00 also works under Windows 95, it is recommended to get the Windows 95 version from one of the network services so that you can operate full Mwave functions in the Windows 95 environment and to take advantage of the 32bit and Plug and Play operating system. It is required to use the ThinkPad Plug and Play BIOS for Mwave in order to run Mwave drivers for Windows 95 with full Windows 95 Plug and Play functions. The following defines the installation procedures for installing the Mwave for Windows 95 drivers. There are separate sections depending on whether or not Windows 95 has already been installed. Section A Existing Windows 3.1 systems - Mwave software for Windows is at version 1.0, 1.1 or 2.0 or New Windows 95 installation - No Mwave software installed Section B Systems that have Windows 95 installed - Mwave software for Windows is at version 1.0, 1.1 or 2.0 Section C Installing MIDI samples Section D. Troubleshooting Conflicts after Mwave for Windows 95 installation is complete ===================================================================== Section A. STARTING WITH WINDOWS 3.1 AND MWAVE FOR WINDOWS 1.0, 1.1 OR 2.0 --------------------------------------------------------------------- For installing Mwave for Windows 95 drivers on a ThinkPad, the following steps are required. This works for systems that have previous versions of Mwave running under Windows 3.1 and systems that do not have Mwave software installed. Step 1. The user must upgrade to the correct Windows 95 BIOS for their specific ThinkPad machine. Step 2. The user installs Windows 95. Step 3. The user boots Windows 95 and installs the Mwave DOS and Windows 95 drivers. 1. Install the ThinkPad Plug & Play BIOS for Mwave. Boot the ThinkPad with the System Program Service Diskette in the floppy disk drive and follow the instructions on the diskette for installing BIOS. Power off the ThinkPad after installation of the BIOS. Initialize the ThinkPad BIOS. After the installation of the ThinkPad BIOS, you must run the ThinkPad CMOS setup program to initialize the ThinkPad BIOS. Power up the ThinkPad while pressing F1 until you get the Easy- Setup Screen. Select Config and then select Initialization. Exit this screen and then select Restart. 2. Install the Windows 95 Operating System. Follow the Windows 95 setup instructions to install Windows 95 on your system. If OS/2 is installed on your system, it is suggested that you download the "Just Add Warp" utility from one of the following locations first; IBM PC Co. BBS - OS/2 Text Files area America Online - OS/2 Forum Canadian IBM BBS Compuserve - GO DRK95 Prodigy - OS/2 Club TalkLink - OS/2 file area This utility will help you install Windows 95 with OS/2 Warp on the system. If you want to get rid of OS/2, you can follow the directions in your Windows 95 installation guide and your OS/2 system guides with respect to removing OS/2. It is recommended to save the old system files when prompted during the Windows 95 installation process. After the Windows 95 install, and before you install the Mwave for Windows 95 Disks, do not change any configuration settings. Some settings may appear to be in conflict or incorrect, but do not attempt to modify them at this time. 3. Install the Mwave for DOS version 2.0 Disks. (MWAVE DOS MUST BE INSTALLED BEFORE MWAVE WINDOWS 95) If not already on a Windows 95 desktop, start Windows 95. Once started, follow this sequence: - Select Start - Select Shutdown - Select Restart the Computer in MS-DOS Mode - Insert the Mwave for DOS Diskette 1 of 2 into the floppy drive - At the DOS command prompt, type "a:install" - Follow the instructions presented Install the Mwave for Windows 95 Disks. If not already on a Windows 95 desktop, start Windows 95. Once started, follow this sequence: - Select Start - Select Run - Insert the Mwave for Windows 95 Diskette 1 of 2 into the floppy drive - At the prompt, type "a:setup" - Follow the instructions presented Verify Mwave Function. If any Mwave function is not working properly, verify that there are no conflicts on the system with the DSP, Comm ports, modem, Sound Blaster support, and MIDI. Identify and resolve any conflicts with Mwave resources. See "Section D" for additional assistance concerning this. Section B. STARTING WITH WINDOWS 95 AND MWAVE FOR WINDOWS 1.0, 1.1 OR 2.0 --------------------------------------------------------------------- Before attempting this process, ensure that there are no Windows 95 system conflicts by selecting Start/Settings/Control Panel, click System, then click Device Manager. Identify and resolve any conflicts. Consult the Windows 95 Users guide (Introducing Windows 95) for assistance. Step 1. The user must upgrade to the correct Windows 95 BIOS for their specific ThinkPad machine. Step 2. The user boots Windows 95 and installs the Mwave for Windows 95 software. 1. Install the ThinkPad Plug & Play BIOS for Mwave. Boot the ThinkPad with the System Program Service Diskette in the floppy disk drive and follow the instructions on the diskette for installing BIOS. Power off the ThinkPad after installation of the BIOS. Initialize the ThinkPad BIOS. After the installation of the ThinkPad BIOS, you must run the ThinkPad CMOS setup program to initialize the ThinkPad BIOS. Power up the ThinkPad while pressing F1 until you get the Easy- Setup Screen. Select Config and then select Initialization. Exit this screen and then select Restart. 2. Install the Mwave for DOS version 2.0 Disks. (MWAVE DOS MUST BE INSTALLED BEFORE MWAVE WINDOWS 95 ) If not already on a Windows 95 desktop, start Windows 95. Once started, follow this sequence: - Select Start - Select Shutdown - Select Restart the Computer in MS-DOS Mode - Insert the Mwave for DOS Diskette 1 of 2 into the floppy drive - At the DOS command prompt, type "a:install" - Follow the instructions presented Install the Mwave for Windows 95 Disks. If not already on a Windows 95 desktop, start Windows 95. Once started, follow this sequence: - Select Start - Select Run - Insert the Mwave for Windows 95 Diskette 1 of 2 into the floppy drive - At the prompt, type "a:setup" - Follow the instructions presented Verify Mwave Function. If any Mwave function is not working properly, verify that there are no conflicts on the system with the DSP, Comm ports, modem, Sound Blaster support, and MIDI. Identify and resolve any conflicts with Mwave resources. If there are conflicts then see the troubleshooting "Section D". Section C. Installing MIDI samples ---------------------------------- The MIDI samples do not need to be re-installed unless the samples have never been installed and you wish to do so at this time or if they have been erased. If you install the samples, please check the Readme file on these disks before installing. To install the MIDI samples; - Select Start - Select Run - Insert the MIDI Samples Diskette 1 for Windows into the floppy drive - At the prompt, type "a:setup" - Follow the instructions presented Section D. Troubleshooting Conflicts ------------------------------------ 1. Comm Port problems Most conflicts will be related to Comm ports and modems. The following steps usually resolve any conflicts in this area. Go to Start, Settings, Control Panel, System, Device Manager. This screen shows the Comm ports and Modem selections for the system and identifies any conflicts. Selecting PORTS will expand to show the details of the Comm Port system resources. A yellow "!" identifies a conflict and a red "X" shows a device that is disabled for various reasons. If there are any red or yellow identifiers, then you should remove these devices by selecting each one and then selecting REMOVE at the bottom of the screen. Before restarting your system, select MODEMS on the same screen and if there are any yellow or red indicators, then remove these also by selecting the appropriate modem and selecting REMOVE at the bottom of the screen. Restart Windows 95 and these system resources will be automatically identified by Windows 95 during the Power up sequence. Check these resources after powering up to verify that there are no yellow or red indicators at this time in the same manner as above. If there are no indicators then Mwave and Windows 95 are installed correctly. Note: If the Comm Port of the Mwave Modem has been changed then your communications applications may have to be manually changed so that the Comm Port of the modem and the application match. 2. Audio problems If you experience problems with playing audio wave files such as System hangs or other Mwave related failures after the installation of the Mwave driver for Windows 95, you may need to also install Mwave audio patch for Windows 95. You may encounter the problem with only files that have been recorded at a sampling rate 11.000 or 22.000 kHz. Most wave files are recorded at 11.025, 22.050, and 44.100 kHz and are not a problem. You may experience problems with the MindPath Presentation F/X Pro, America Online and other applications that have wave files with 11.000 or 22.000 kHz format. If you experience this, then download the Mwave audio patch for Windows 95 and follow the installation instructions. The patch is in Package MW95WAV.EXE. 10.1.6. Infrared Device Driver ------------------------------ You can use ThinkPad Infrared device driver on Windows 95. If you have ThinkPad Infrared Device driver working on Windows and plan to migrate to Windows 95, the Infrared device driver will be migrated to Windows 95 environment automatically. If you don't have ThinkPad Infrared device driver on your Windows system or you are going to install Windows 95 on a blank hard disk, you can install ThinkPad Infrared device driver after you install Windows 95 on your system by the following procedure. 1. Turn on the computer; then go to the MS-DOS command prompt. 2. Insert the Infrared Features Diskette into the diskette drive. 3. Type "A:UINSTALL" and press Enter. 4. At the "Installation Options" screen, press Enter to accept the default source drive. 5. Follow the instructions on the screen. 6. Select Install Windows ThinkPad Infrared Driver when you are asked. Make sure you specify the directory where you have installed Windows 95 when asked. You have completed the installation of the infrared device driver. --------------------------------------------------------- If you don't have ThinkPad Infrared device driver version 2.01, you may encounter some problems. Get the version 2.01 driver to use Infrared functions under Windows 95 correctly. --------------------------------------------------------------------- 10.2. Known limitations with Windows 95 -------------------------------------- o Windows 95 logo screen becomes brown Upon Windows 95 boot, its logo screen background becomes brown. This is normal and everything works fine after Windows 95 desktop screen appears. o FaxWorks Voice problems FaxWorks Voice, which is one of the preinstalled applications, has the following problems under Windows 95. - Telephone Icon is not displayed properly The FaxWorks telephone icon is not displayed properly as it is in Windows 3.x. When you start one of FaxWorks Voice functions such as Call Center, the telephone icon is displayed over the program name of title bar. Once you minimize Call Center, the telephone icon disappears from the title bar but some garbage might remain on the Windows 95 desktop screen. This cosmetic problem doesn't affect the actual functions of FaxWorks Voice. - When you close the windows of FaxWorks Voice fax viewing, the system may encounter a problem and you might have to reboot the system. - If you have any problem related to sending/receiving fax by FaxWorks Voice, check the following. 1. Click "My Computer"; click "Printers"; double click "FaxWorks Printer Driver (FX-WORKS)". 2. Click on "Details" tab; verify that MWV is selected in "Print to the following port". Windows 95 might show "MWV (Unknown local port)" but it is normal. --------------------------------------------------------------- Above limitations are expected to be fixed in the next version of FaxWorks Voice program (revision 3.00g or later). The Package name of FaxWorks Voice Version 3.00.g.058 is FWVMW058.EXE. --------------------------------------------------------------------- ----------------------------------------------------------------------- 11. System independent information ---------------------------------- 11.1. Suspend command on Start menu ----------------------------------- The "Suspend" command should be visible in the "Start" menu above "Shut Down" command. If Windows 95 that you have doesn't enable this "Suspend" command, please take the following steps to correct the problem. 1. Click "My Computer" 2. Click "Control Panel" 3. Click "System" 4. Click on "Device Manager" tab 5. Select "System Devices", "Advanced Power Management", "Settings" 6. Verify that "Enable Power management support" is selected 7. Click "OK" 1. Click "My Computer" 2. Click "Control Panel" 3. Click "Power" 4. Select either "Always" or "Only when undocked" (depending on a type of ThinkPad you have) in "Show Suspend command on Start menu" box. 11.2. PCMCIA function limitations -------------------------------- When you inserted a PC card into PCMCIA slots of ThinkPad, the suspend function has the following limitations by design. - When the system is power by AC, ThinkPad doesn't enter full suspend and enters standby mode. - When the system is power by battery, ThinkPad always enter suspend mode regardless of the PC card status. You may lose the connection if your PC card is a network card or modem. The PCMCIA support software in Windows 95 has the following limitations. - It does not support the ring indicator of PCMCIA modem cards. Therefore, you cannot use ring indications by PCMCIA modems even if it's support by cards. - It does not support PCMCIA harddisks power down, even if it's supported by harddisks. - It does not support the system boot from PCMCIA harddisks. 11.3. PCMCIA network adapter card compatibility in Dock II ---------------------------------------------------------- You may not be able to enable or get your PCMCIA network adapter correctly when the card is inserted into the PCMCIA slot of IBM Dock II docking station. If your card is working fine in the ThinkPad internal PCMCIA slots, you need to contact IBM PC Company HelpCenter and request the patch file, YPTF012.EXE. 11.4. PCMCIA support software setup ---------------------------------- The Windows 95 installation program doesn't enable its own 32bit PCMCIA support software. If you have a ThinkPad on which the ThinkPad DOS/Windows PCMCIA support software is already installed and want to use it after you install Windows 95 on the ThinkPad, you don't have to perform any specific setup. The Windows 95 installation program automatically migrates the installed ThinkPad PCMCIA support software over to Windows 95 environment. If you have a ThinkPad on which the ThinkPad DOS/Windows PCMCIA support software is already installed but want to use Windows 95 PCMCIA support software after you install Windows 95 on the ThinkPad, follow the next steps. 1. Click "My Computer" 2. Click "Control Panel" 3. Click "PC Card" 4. Select "No" for the question "Are you using a PC card to install Windows?"; then click "Next" 5. Select "Yes" for the question "Would you like to review the change to your system files before Windows disable these drivers?"; then click "Next" 6. Verify that the following statements are highlighted to be removed from your CONFIG.SYS. DEVICE=C:\THINKPAD\IBMDSS01.SYS DEVICE=C:\THINKPAD\IBMDOSCS.SYS DEVICE=C:\THINKPAD\DICRMU01.SYS DEVICE=C:\THINKPAD\$ICPMDOS.SYS DEVICE=C:\THINKPAD\AUTODRV.SYS C:\THINKPAD\AUTODRV.INI DEVICE=C:\THINKPAD\SRAMDRV2.SYS Click "Next"; Windows 95 also lets you review AUTOEXEC.BAT and SYSTEM.INI. There are no ThinkPad PCMCIA support software setup included in AUTOEXEC.BAT and SYSTEM.INI. 7. After you review all the system files, click "Finish" to complete the Windows 95 PCMCIA support setup. If you want to use the ThinkPad PCMCIA support software after you enabled the Windows 95 PCMCIA support software, you MUST disable Windows 95 PCMCIA support again. Windows 95 disables its own PCMCIA support as default. To make sure this; 1. Click "My Computer" 2. Click "Control Panel" 3. Click "System" 4. Click on "Device Manager" tab 5. Click "+" mark on "PCMCIA socket" 6. Verify that "PCIC or compatible PCMCIA controller" is disabled. (Red "X" sign should be visible on the PCIC icon, and "Device Status" is "This device is disabled" when you double click the PCIC icon.) If the PCMCIA controller is already enabled ("Device Status" is "This device is working properly".), highlight "PCIC or compatible PCMCIA controller" by clicking the PCIC icon; click "Remove" button; then follow the instructions to disable Windows 95 PCMCIA support. 11.5. ThinkPad Docking control utility ------------------------------------- If you have installed Windows 95 over a ThinkPad on which the Docking control utility program for Windows is already installed, don't use the utility. The Docking control utility provides several docking functions under Windows but is not necessary under Windows 95 any longer. All the docking capability by this utility is now provided by ThinkPad Plug-and-Play BIOS and Windows 95 Plug-and- Play support. You don't have to install or use any specific programs to enable ThinkPad docking functions under Windows 95. It is recommended to remove the following statements from Windows INI files. o WIN.INI file [windows] : load=C:\THINKPAD\DOCKWIN.EXE <-remove this statement : o SYSTEM.INI file : [386Enh] : device=IBMPNP.386 <-remove this statement : 11.6. ThinkPad Dock II docking station ------------------------------------- ThinkPad Dock II docking station supports docking and undocking operations without system power off. You can dock and undock the system when it is suspended (warm docking), or you can dock and undock the system when it is powered on (hot docking). This feature is available for 755, 701, 360 and 370 systems. When you use hot / warm docking, you must disable the host adapter SCSI BIOS of Dock II docking station. You can disable the host adapter SCSI BIOS by the Dock II SCSISelect utility. Press Ctrl+A when prompted at boot time. Then select "Configure/View Host Adapter Settings" and disable the Host Adapter BIOS. You can also disable the host adapter BIOS by dip switches. For further information, refer to "Chapter 5. Using the SCSI Controller" of Dock II User's Guide. ----------------------------------------------------------------------- 12. Other ThinkPad Systems -------------------------- 12.1. ThinkPad 750 systems -------------------------- 12.1.1 Install and setup Windows 95 on ThinkPad ----------------------------------------------- IBM is testing the ThinkPad 750 systems with Windows 95 but only APM BIOS 1.0 is supported. No PnP BIOS support is available on those systems. 12.1.0.0. Before you proceed ---------------------------- Again, you are strongly recommended to get the latest system program service diskette (version 1.41 or later) and update your system BIOS. 12.1.1.1. Video device drivers ------------------------------ To set up or install the video device driver on ThinkPad 750 systems, refer to "Section 2.1.2. Video device driver - ThinkPad 755C/Cs". 12.1.1.2. ThinkPad Features --------------------------- To set up or install the ThinkPad Features on ThinkPad 750 systems, refer to "Section 2.1.3. ThinkPad Features - ThinkPad 755C/Cs". 12.1.1.3. PCMCIA device drivers ------------------------------ To set up or install the PCMCIA device driver on ThinkPad 750 systems, refer to "Section 2.1.4. PCMCIA device driver - ThinkPad 755C/Cs". 12.1.1.4. Audio support software -------------------------------- To set up or install the audio support software on ThinkPad 750 systems, refer to "Section 2.1.5. Audio Support software - ThinkPad 755C/Cs". 12.1.2. Known limitations with Windows 95 ----------------------------------------- For limitations and problems with ThinkPad 750 systems on Windows 95, refer to "Section 2.2 - ThinkPad 755C/Cs". 12.2. ThinkPad 340 system ------------------------- 12.2.1 Install and setup Windows 95 on ThinkPad ----------------------------------------------- IBM is testing the ThinkPad 340 system with Windows 95 but only APM BIOS 1.0 is supported. No PnP BIOS support is available on those systems. 12.2.1.1. Video device drivers ------------------------------ There's no special video device driver is available for ThinkPad 340. You can use the standard VGA display driver available in Windows 95. 12.2.1.2. ThinkPad Features Program ----------------------------------- To set up or install the ThinkPad Features on ThinkPad 340 systems, refer to "Section 4.1.2. ThinkPad Features - ThinkPad 340CSE". 12.2.1.3. PCMCIA Device driver ------------------------------ To set up or install the PCMCIA device driver on ThinkPad 340 systems, refer to "Section 4.1.3. PCMCIA device driver - ThinkPad 340". 12.2.2. Known limitations with Windows 95 ----------------------------------------- For limitations and problems with ThinkPad 340 system on Windows 95, refer to "Section 4.2 - ThinkPad 340CSE". Note that the video display related problems are not applicable. 12.3. ThinkPad 230Cs system (Available only in Japan) ----------------------------------------------------- 12.3.1. Install and setup Windows 95 on ThinkPad ------------------------------------------------ IBM is testing the ThinkPad 230Cs system with Windows 95 but only APM BIOS 1.0 is supported. No PnP BIOS support is available on those systems. 12.3.1.1. Video device drivers ------------------------------ The video device driver for ThinkPad 230Cs systems is included in Windows 95 and it is automatically installed by Windows 95 Setup program. You don't need ThinkPad Windows video device driver any longer. 1. After installing or set up Windows 95 on your ThinkPad; click "My Computer". 2. Click "Control Panel"; Click "Display"; Click on "Setting" tab. 3. Click "Change Display Type..." button. 4. Make sure that Adapter Type is "Cirrus Logic". 12.3.1.2. ThinkPad Features --------------------------- To set up or install the ThinkPad Features on ThinkPad 230Cs system, refer to "Section 2.1.3. ThinkPad Features - ThinkPad 755C/Cs". 12.3.1.3. PCMCIA device drivers ------------------------------ To set up or install the PCMCIA device driver on ThinkPad 230Cs systems, refer to "Section 2.1.4. PCMCIA device driver - ThinkPad 755C/Cs". 12.3.2. Known limitations with Windows 95 ----------------------------------------- o Audio support software causes system hang The audio support software of ThinkPad 230Cs needs to be updated to work with Windows 95 correctly. Get the updated audio driver from Nifty-Serve or PEOPLE BBS in Japan. 12.4. Other ThinkPad systems ---------------------------- IBM is not testing any other ThinkPad systems with Windows 95. Windows 95 may run on those ThinkPad systems but IBM does not plan to test Windows 95 on those systems. ------------------------------------------------------