home *** CD-ROM | disk | FTP | other *** search
/ IBM Thinkpad Drivers FTP / 760LDSAS.TXT < prev    next >
Text File  |  1997-01-01  |  7KB  |  170 lines

  1.          Thinkpad 760LD Original Files for DOS/WIN and OS/2 Warp Preload
  2. ===============================================================================
  3.  
  4. CONTENTS
  5. ---------
  6.  
  7. 1.   Description of this diskette
  8. 2.   Restoring the original CONFIG.SYS and AUTOEXEC.BAT for DOS and OS/2
  9. 3.   Restoring the original OS/2 Warp desktop
  10. 4.   Other configuration files included
  11.  
  12.  
  13. 1.   Description of this diskette
  14. ---------------------------------
  15.  
  16.      This diskette is to be used with the above specified model IBM ThinkPads
  17. ONLY.  It CANNOT be used on ANY other model of ThinkPad.  It contains certain
  18. original files from the pre-loaded operating system and can be used to replace
  19. your current ones to resolve configuration problems. The original OS/2 desktop
  20. can also be restored using this diskette.
  21.  
  22.      This diskette and its contents may not fix all problems, it is simply a
  23. back up of those original files. Contact an IBM technical support
  24. representative at 1-800-772-2227 if assistance is needed.
  25.  
  26.  
  27.  
  28.  
  29. 2.   Restoring the original CONFIG.SYS and AUTOEXEC.BAT for DOS and OS/2
  30. ------------------------------------------------------------------------
  31.  
  32.      The original CONFIG.SYS and AUTOEXEC.BAT for DOS and OS/2 are in the
  33. A:\OS2\SYSTEM directory with the extentions .DOS and .OS2.  Before replacing
  34. your current files, it is advisable to back them up,copy them to a floppy, or
  35. rename them.
  36.  
  37. To replace the OS/2 CONFIG.SYS, first ensure that WARP was the operating system
  38. that the unit was last booted in and use the following command:
  39.  
  40. COPY A:\OS2\SYSTEM\CONFIG.OS2 C:\CONFIG.SYS   followed by the <enter> key.
  41.  
  42.  
  43. To replace the OS/2 AUTOEXEC.BAT, first ensure that WARP was the operating
  44. system that the unit was last booted in and use the following command:
  45.  
  46. COPY A:\OS2\SYSTEM\AUTOEXEC.OS2 C:\AUTOEXEC.BAT   followed by the <enter> key.
  47.  
  48.  
  49. To replace the DOS CONFIG.SYS, first ensure that DOS/WINDOWS was the operating
  50. system that the unit was last booted in and use the following command:
  51.  
  52. COPY A:\OS2\SYSTEM\CONFIG.DOS C:\CONFIG.SYS   followed by the <enter> key.
  53.  
  54.  
  55. To replace the DOS AUTOEXEC.BAT, first ensure that DOS\WINDOWS was the
  56. operating system that the unit was last booted in and use the following
  57. command:
  58.  
  59. COPY A:\OS2\SYSTEM\AUTOEXEC.DOS C:\AUTOEXEC.BAT   followed by the <enter> key.
  60.  
  61.  
  62.  
  63.  
  64.  
  65. 3.   Restoring the original OS/2 Warp desktop
  66. ---------------------------------------------
  67.  
  68.      The following procedure will restore the original OS/2 desktop for the
  69. intended models listed above and should be used for those models ONLY.
  70. It will not replace any of the pre-installed software that may have
  71. been deleted.  If, prior to the OS/2 desktop restore, there were programs and
  72. files that had been removed from the hard drive, any OS/2 objects on the
  73. restored desktop that correspond to those programs will not function, and such
  74. desktop objects should be deleted.
  75.  
  76.  
  77. IMPORTANT NOTE:
  78.  
  79.      Before performing the following procedure, you will need either the
  80. OS/2 Utility diskettes or the first three OS/2 Installation diskettes.
  81. You must run a CHKDSK before restoring the desktop.
  82.  
  83.  
  84.      To perform a CHKDSK, boot the computer from either the OS/2 Installation
  85. diskette or Utility diskette #1 and continue with the next diskette when
  86. prompted.  The Utility diskettes will boot to an A:\> prompt; if you are using
  87. the Installation diskettes, when the blue welcome screen appears, use F3 to get
  88. to a command prompt.  Insert either OS/2 diskette #2 or Utility diskette #3 and
  89. at the A:\> prompt, use the following command:
  90.  
  91. CHKDSK C: /F    followed by the <enter> key
  92.  
  93.      DO NOT change to drive C: before using this command.  This will cause OS/2
  94. to lock the drive and fixes cannot be made.  If errors are found, run the
  95. command again until no errors are found.
  96.  
  97.  
  98.      The restore can only be done while either booted from floppies or booted
  99. to a command prompt by hitting the ALT-F1 key combination when the white
  100. rectangle with the "OS/2" label appears on boot, and choosing "C" from the
  101. recovery menu.
  102.  
  103.  
  104. Restore the Desktop by using the following commands from the A:\ prompt:
  105.  
  106.  
  107. C:    followed by the <enter> key
  108. CD\OS2    followed by the <enter> key
  109. RESTORE A: C:\*.* /S    followed by the <enter> key
  110.  
  111.  
  112. Next copy the OS/2 INI files to the C:\OS2 directory with the following
  113. commands:
  114.  
  115. COPY A:\OS2\OS2*.INI C:\OS2    followed by the <enter> key.
  116.  
  117.  
  118. It may or may not be necessary to replace the OS/2 CONFIG.SYS when using this
  119. procedure.
  120.  
  121.      If the machine boots to a black screen, use Ctrl-Alt-Del to reboot the
  122. system.  When the white rectangle with the "OS/2" label appears on use the
  123. Alt-F1 key combination to get to the recovery screen.  Choose "V" to set the
  124. system back to VGA.  If the machine still does not boot, and you created an
  125. archive, try restoring it.  If problems persist, contact an IBM support
  126. representative.
  127.  
  128.  
  129.  
  130.  
  131. 4.   Other configuration files.
  132. -------------------------------
  133.  
  134.      For configuration problems, this diskette contains other original files
  135. from the system in the same directories on the diskette that they would be
  136. found on your hard drive.  These include windows group files with the .GRP
  137. extension and all of the .INI files, such as the WIN.INI or SYSTEM.INI.  These
  138. can be used to resolve many configuration problems.  You may want to back up or
  139. rename any current configuration files before replacing them with the
  140. originals.
  141.  
  142.  
  143.      For example, to replace the current windows SYSTEM.INI with the original,
  144. use the following command:
  145.  
  146. COPY A:\WINDOWS\SYSTEM.INI C:\WINDOWS    followed by the <enter> key.
  147.  
  148.  
  149.  
  150.  
  151.  
  152.  
  153. *-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
  154. NOTE:
  155. ** NO WARRANTY **  ANY USE BY YOU OF THE SOFTWARE IS AT YOUR OWN RISK.
  156. THE SOFTWARE IS PROVIDED FOR USE "AS IS" WITHOUT WARRANTY OF ANY KIND.
  157. TO THE MAXIMUM EXTENT PERMITTED BY LAW, IBM AND ITS SUPPLIERS DISCLAIM
  158. ALL WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
  159. LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
  160. PARTICULAR PURPOSE. IBM IS NOT OBLIGATED TO PROVIDE ANY UPDATES TO THE
  161. SOFTWARE.
  162.  
  163. NO LIABILITY FOR CONSEQUENTIAL DAMAGES.  In no event shall IBM or its
  164. suppliers be liable for any damages whatsoever (including, without limitation,
  165. incidental, direct, indirect special and consequential damages, damages for
  166. loss of business profits, business interruption, loss of business information,
  167. or other pecuniary loss) arising out of the use or inability to use this
  168. product, even if IBM has been advised of the possibility of such damages.
  169. *-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
  170.