Enter a check setup name.  If the F3 key is pressed,
 a table of setups will pop up.  Select one using the
 and 
 or the locator on the top line, then press Enter
 to use it.
 Enter the indicated information to print on the check.
 If the date is left blank, today's date will be used.
 If the Payee is left blank, a lookup table will pop up
 to allow selection of the Payee name.  This is the same
 Table used in the envelope printing selection.  The amount  
 is required.  The Name table can also be popped up by
 pressing F4.
 Press F5 to enter or modify the laser printer control
 sequences.  Press F9 to clear the check data.  The check
 data will be saved for the next time you run the program
 unless cleared with F9.
 When the data is correct, press F2 to print the check.  If  
 the printer controls are correct, the printer will feed a
 check from the manual feed tray and print it.
 These are the HP LaserJet Plus control codes for the various functions
 used by the printing routines.  If you are using a non-HP printer with
 LaserJet Plus emulation, you may want to change the Reset Printer and
 Set Font Attributes control sequences to the native commands used by your
 printer.  The Reset
 sequence should put the
 printer in LaserJet Plus
 emulation mode and the
 Set Font Attributes should
 select the desired font.
 The font must be a land-
 scape font, preferable a
 12 pitch, 10 point font.
 The positioning controls
 should not be changed,
 since the program will
 insert actual positioning
 values (in decipoints) into these sequences.  The Reset Printer and Set
 Font Attributes sequences are 32 characters long, although only 20 charac-
 ters show at a time.
 If your printer commands do not require an Escape, make the first character  
 of the command sequenc a blank.
 Enter an envelope name.  If the F3 key is pressed,  the
 Envelope Setup table will pop up.  Select a setup using the
 and 
 keys or the Locate box.  Press Enter to use the
 envelope setup.
 Enter the indicated information to print on the envelope.
 If the Name is left blank, a lookup table will pop up
 to allow selection of the Payee name and address.  From
 this table, you can enter names and addresses.  Any changes
 made on this screen will be reflected in the permanent name
 and address table as well.  The Name table can also be popped  
 up by pressing F4.
 Press F5 to enter or modify the laser printer control
 sequences.
 When the data is correct, press F2 to print the envelope.  If  
 the printer controls are correct, the printer will feed a
 envelope from the manual feed tray and print it.
 Use the 
 and 
 keys to select a menu option.  You can also select an option
 by pressing the first letter of the menu choice, i.e. 'C' will select Check 
 Print, 'E' will select Envelope Print and 'Q' will select Quit.
 Press enter to execute your choice.
 To exit any screen (exit this menu), press the Esc key in the first field
 on the screen, or Ctl-Esc anywhere on the screen.  The PgUp and PgDn keys
 will scroll the Name table, Ctl-PgUp and Ctl-PgDn will go to the first or
 last page of the Name table.
 Enter the name and address information in this form.  This information will  
 be saved in a permanent file for future use.  The first name line is also
 available in the check printing routine.  You can go backward throught the
 form with the escape or 
 key.  Complete each field with the Enter or 
 key. 
 If you want to completely discard the data for a new name, press Ctl-Escape. 
 The Home and End keys will put the cursor at the first and last characters
 of a field.  The Ins key will toggle the insert/overwrite modes.  The Del
 and Backspace keys work as usual.
 Use the 
 and 
 keys to select a
 name, or enter the first few letters
 of the name in the Locate box at
 the top of the table.  When the
 desired name is highlited, press
 enter to fill in the envelope form. 
 To add a new name, press the Ins
 key and fill in the information.
 To delete a name, press the Del key 
 when the desired name is highlited. 
 To change a name and address, press 
 F9 when the desired name is high-
 lited.  These names are also avail- 
 able to the check print section.
 Enter the positions in inches
 relative to the landscape
 mode.  This is most easily
 done by laying a check over
 a sheet of paper and meas-
 uring with a ruler.  Or
 set all to 0.0 and print a
 test check on plain paper.
 Overlay a check and measure
 from the test print.
 Enter the positions in inches
 relative to the landscape
 mode.  This is most easily
 done by laying an envelope
 over a sheet of paper and
 measuring with a ruler.  Or
 set all to 0.0 and print a
 test envelope on plain paper.
 Overlay a envelope and
 measure from the test print.
 Leave return address name
 blank for no preprinted
 envelopes.
!CHK     
CONTROL 
ENV     
MENU    
NAMEFORM
NAMETBL s
POSCHK  
POSENV