Novell Message Librarian Data File Version 1.00 COPYRIGHT (c) 1985 by Novell, Inc. All Rights Reserved. INSTALL v1.02 NetWare Client Install No help available The Windows path given does not point to a valid Windows directory. Please enter a valid windows directory. AUTOEXEC.BAT AUTOEXEC.BNW AUTOEXEC.NEW @CALL %sSTARTNET PATH %s PATH %%PATH%%;%s Insert the %s diskette into drive %s. CONFIG.SYS CONFIG.NEW CONFIG.BNW Highlight setting and press . Press to cancel. LASTDRIVE=Z Press to mark as many selections as needed for this setting. Press to save selections. Press to cancel. Enter a value between %s and %s, then press . Press to cancel. STARTNET.BAT STARTNET.BNW NET.CFG NET.BNW PROGMAN.INI File %s already exists on the destination, and it has a newer date stamp. The Install Utility will not overwrite this newer file unless instructed to do so. PROGMAN.BNW Group%d=%s%s No more help is available. Replace Newer File With Older File? Warning! %s files were not copied during the installation process. There is not enough memory available to run the install program. Insert the target diskette (the diskette you are installing to) into drive %s. <<< BAD MESSAGE >>> Insert the Driver Disk The function keys on your machine are: Exits help. Lists the function keys on your machine. Press to install. Esc-exit Enter-select -move Alt F10-exit Esc-continue Enter-edit -move Alt F10-exit Press when ready or to cancel. Press to see list OTHER DRIVERS Network Board Driver has been successfully configured for the standard parameters. If your driver has customized parameters you may wish to select the driver again to view the parameter settings. The following keys are available while viewing help: %s is being installed. DOSCLINST-1.0-1:%s could not be installed. %s has detected a driver for your network board already installed on this machine. Driver: %s Board Name: %s The latest version of this driver will be installed with the same options. Press to continue. Moves to the next help screen. The network board driver cannot be found. Complete the installation then do the following: 1. Copy the network board driver to your target directory. 2. Modify the "LINK DRIVER" section of your NET.CFG file to include the correct settings. Insert the DRIVER diskette into drive %s. Network Board Old NetWare Tools for Windows exist in your Windows area. These previous versions of NetWare Tools for Windows will not function with your workstation software. We recommend you remove them in the following manner: 1. Delete the file NWTOOLS.EXE from your windows directory. 2. Delete the following icons from the group windows within your windows program manager: Map, SetPass, Printers, Send, Attachments, Messages, UserList, VolInfo The Install Utility creates a new program group named "NetWare." The "User Tools" icon within the "NetWare" group replaces the previous NetWare Tools. The Install Utility is finished. Before rebooting your workstation do the following: 1. Edit your AUTOEXEC.BAT and CONFIG.SYS files to remove any previous NetWare workstation files. The previous contents of these files have been saved with .BNW extentions. 1. Edit the AUTOEXEC.NEW and CONFIG.NEW files in the client directory to meet your system requirements. Remove any previous NetWare workstation files from them. Then, use them to replace your current AUTOEXEC.BAT and CONFIG.SYS files. 2. Reboot your workstation by pressing . Note: The Install Utility created or modified the NET.CFG and STARTNET.BAT files in the client directory, and the WIN.INI, SYSTEM.INI, and PROGMAN.INI files in the windows directory. The previous contents of these files have been saved with .BNW extentions. The %s drive is not ready. Note: The Install Utility created or modified the NET.CFG and STARTNET.BAT files in the client directory. The previous contents of these files have been saved with .BNW extentions. Press to exit install. Enter-continue Alt F10-exit If you did not change the jumpers or switches on your network interface card, press to accept the current values. If you changed the jumpers or switches on you network interface card, change the values above to match the jumber settings. Highlight the value and press . Press when you are through. Note: If you have a parallel printer (this includes most printers) avoid using IO Base Address 360. If you have a device which uses COM2 (ie: fax, mouse, or modem) avoid using Interrupt Request 3. FILES=40 (none) A driver diskette must have the file DRIVER.DOS or have an INS file for each of the drivers on the disk. The Driver Diskette for the current driver must have the files %s and %s on it. If the driver disk can be found in a different place, type the new path below: VeRsIoN=v1.02 Esc-cancel Enter-select and continue -move Alt F10-exit The DOS path must include a drive letter. An invalid drive was given in path. Esc-cancel F5-select Enter-continue -move Alt F10-exit STEP 3. Do you wish to install support for Windows? (Y/N): SM_DEFAULT_MESSAGE Windows Subdirectory: Returns to the previous help screen. STEP 2. Client installation requires "LASTDRIVE=Z" in the CONFIG.SYS file and "CALL STARTNET.BAT" added to STEP 4. Press to install the driver for your network board. You may then use arrow keys to find the STEP 1. Type client directory name for Client Installation. board name. STEP 5. AUTOEXEC.BAT. Install will make backup copies. (C) Copyright 1992 Novell, Inc. Friday Monday Saturday Sunday Thursday Tuesday Wednesday The description for this error is not available. Press to see list Hardware Interrupt Select the interrupt level that corresponds to the interrupt setting on the board or other device. The interrupt setting must be unique (not one used by another device in the machine). Base I/O Port Value must be between %d and %d inclusive. Allow changes? (Y/N): The installation requires you to select a network board driver. Go to Step 4 and select a network board driver. If you cannot find the correct driver, select "Dedicated (Non-ODI) IPX" which is found on the WSDRV_1 diskette. Select the port value (base I/O address) that corresponds to the port address setting on the board or other device. Make sure the block of I/O addresses does not overlap the addresses of another device in the machine. Memory I/O Address Select the memory address that corresponds to the memory setting on the board or other device. Make sure the block of memory addresses does not overlap the addresses of another device in the machine. Select the DMA channel that corresponds to the DMA setting on the board or other device. Make sure the DMA (Direct Memory Access) channel does not conflict with that of another device in the machine. Select the slot number that corresponds to the expansion slot where the board or other device is installed. NODE ADDRESS Node Address Do not change this address unless you are prepared to administer local addresses according to the IEEE 802.2 specifications. The driver defaults to the node address of the board. FRAME Frame Type Select the frame type(s) used by the protocol(s) that your network requires. Make sure you have both the server and client configured for the same frame type. April August December February January March November October September DOSCLINST-1.0-3:The INSTALL.OVL file could not be found. DOSCLINST-1.0-4:A read error occurred while reading the overlay file INSTALL.OVL. The overlay file "%s$RUN.OVL" is the wrong version for this utility. The Paste Buffer is empty. Press to continue. Please wait. Insert the INSTALL diskette into drive %s. DOSCLINST-1.0-2:This program requires more disk space. Installation could not be completed. Settings for the %s