1 mill. 2 colors 3 Ko.Hlp 4 \n\nDo you want more help? 5 Off 6 Max Screen 7 Move Dialogs 8 Max.Scrn. + Mov.Dlg. 9 Adaption of the graphics board to the monitor and adjusting the video parameters. 10 Display: ELSA Settings 11 %Y-%m-%d 51 &Database 100 Hardware Limits 101 If you have stored a graphics mode earlier, you may switch back to it. 102 Your monitor must be entered. Please click on 'Change...' and check the entered values.\nMost important is the maximal horizontal scan frequency (in kHz) of your monitor. 103 Select your wanted color depth.\nUsually 256 colors are good enough, for videos or 3-D applications 32678 or 65536 colors offer better performance and for sphisticated image processing 16.7 million colors may make sense. 104 Select your wanted refresh rate, e.g. 75 Hz.\nIf you are not sure about the capabilities of your monitor, select 75 Hz. Usually 85 Hz are very good.\nA more acurate adjustment you may do after clicking on the 'Details...' button. 105 This slider adjusts the visible screen resolution. The resolution indicates the number of pixels that can be displayed horizontally and vertically. It should fit to the screen size. It should be 1024 x 768 for 17'' monitors (43 cm CRT diagonal) , less for smaller monitors and more for larger monitors. 106 This slider adjusts the virtual screen resolution (Panning). 258 Ȳ0timingX 8p@ ܴ 8 ̬X|iȲ.ĬX ȲL? 261 The graphics mode is stored and will become active at the next start of Windows.\n\nPlease close all DOS boxes and DOS applications.\nMay Windows be restarted right now? 267 TtX l0| piȲ.l0| pXՔ p X t p Ttt \|ij ǵȲ.windows ,t И JD 15| 0䲬t Ƙ $t )Ȳ. 268 The monitor order will be changed from '%1' to '%2'.\nAt the same time no other parameters are modified.\n\nThe monitor order will be changed now? 269 An old version of the ELSA WINman is on your computer in the directory '%1'.\nDelete this version? 270 For small screen resolutions the font size must be switched to 'Small Fonts'.\nChange to the dialog page 'Display Properties'/'Settings'.\n\nDo you want store the new settings without modifying the font size? 271 You have selected a color depth of 65536 colors (16 bpp). In this mode some programms (especially 3-D programms) will work with restrictions or with less performance. No Direct3D hardware acceleration would be available.\nUsually the prefered color depth is 32768 colors (15 bpp).\n\nDo you want select 32768 colors (recommended)? 272 The property page "ELSA Settings (WINman)" is not active.\nThere may be a conflict, when the standard "Settings" page was active.\nDo you want to retain the Settings of the "ELSA Settings (WINman)" page and ignore the standard "Settings" page? 273 To switch from multi-screen mode to single-screen mode, you should install the ELSA driver for single-screen mode\n(under Control Panel/Display/Settings/Change Configuration...).\nYou can use the multi-screen driver, but there you will experience a loss in performance. \n\nDo you wish to switch to single-screen? 278 Ȳ0X pŴ@ƨxD X”. 279 Please first select a timing. 280 VDIF file successfully stored. 281 Your monitor has changed.\nPlease confirm the shown data or enter new data. 288  tǬ t ٳ<\ ƘX $D XƵȲ. 289 (D %d ͬ XŵȲ.) 291 You have running another application, which uses DirectDraw.\nIt would be better to terminate this application.\nOtherwise you may get screen disturbances as long as the computer is not restarted. 300 Your monitor is compatible with VESA DDC. But the data found may be not the optimum.\nPlease correct especially the monitor name and the maximum kHz and Hz values. 301 tXՔ ]  t ̸Ȳ. tX | \ͳT X0 X Ȳ0X l0@ Hij l(D Uֈ %X”. 515 This graphics board has only fix predefined graphics modes! 522 Error: The monitor database cannot be opened! 526 Error: There is already a file with this name. Enter a new name for the VDIF file! 527 Error: The VDIF file cannot be stored! 528 Error: The selected file cannot be opened or is no valid VESA VDIF monitor description file! 529 Error: The first value of the range must be lower than the second value! 533 Error: Windows cannot be restarted!\n\nAbort = back to previous settings\nRetry = another try\nIgnore = no restart of Windows, changed settings will be realized at next Windows restart 535 This setting can be done only after you have entered the maximal allowed horizontal scan rate (in kHz) of all of your monitors (otherwise your monitor may be damaged).\nPlease use the 'Change...' button under 'Monitor'. 536 Error: Cannot switch graphics mode!\nPlease open the Properties of Display and switch to ELSA Settings. 537 Error: ELSA Settings cannot switch to this graphics mode!\n 538 Error: ELSA Settings cannot switch to this graphics mode, because it is not possible to write to the registry!\nMay be your user account has too less rights for this area in the registry. Your administrator can give you these rights. The procedere is described either in the README.TXT of the ELSA Windows driver or in the help to ELSA Settings.\nDo you want see the help? 539 The maximal allowed horizontal scan rate (in kHz) of the monitor number %1 is not entered.\nDo you want take the data of the first monitor also for this monitor? 540 Do you want this settings also for all other monitors?