HL-10 Lifting Body

The HL-10 was one of five lifting body designs flown at NASA's Dryden Flight Research Center, Edwards, CA, from July 1966 to Nov. 1975 to study and validate the concept of safely maneuvering and landing a low lift-over-drag vehicle designed for reentry from space. It is now on permanent public display near the main entrance of Dryden.

The other designs were the M2-F2, M2-F3 (rebuilt M2-F2 following a landing accident), X-24A, and X-24B (rebuilt X-24A with a different aerodynamic shape).

Wingless lifting bodies attained aerodynamic stability and lift from the shape of the vehicle. Lift resulted from more air pressure on the bottom of the body than on the top. They used energy and aerodynamic lift for in-flight maneuvering and a powerless, glider-like landing.

Background

The lifting body concept was originally tested at Dryden with a plywood prototype designated the M2-F1 and built in late 1962. It featured a plywood shell built by Gus Briegleb, a sailplane builder from Mirage Dry Lake, CA, placed over a tubular frame built at Dryden. The M2-F1 was towed aloft, first behind an auto and then a C-47 more than 100 times, to validate basic lifting body stability and control characteristics. This led to establishment of the formal program which resulted in the HL-10 and its sister vehicles.

Northrop Corporation built the HL-10. The contract for construction of the HL-10 and the M2-F2, first of the fleet of lifting bodies flown at Dryden and also built by Northrop, was $1.8 million. "HL" stands for horizontal landing, and "10" refers to the tenth design studied by engineers at NASA's Langley Research Center, Hampton, VA.

The HL-10 was delivered to NASA in Jan. 1966. During the next ten months it was instrumented for the research program and prepared for flight. The HL-10 and the M2-F2 were tested in wind tunnels at Ames Research Center before research flights began.

The first flight of the HL-10 was on Dec. 22, 1966, with research pilot Bruce Peterson in the cockpit. Although an XLR-11 rocket engine was installed in the vehicle, the first 11 drop flights from the B-52 launch aircraft were powerless glide flights to assess handling qualities, stability, and control.

The HL-10 was flown 37 times during the lifting body research program and logged the highest altitude and fastest speed in the program. On Feb. 18, 1970, Air Force test pilot Peter Hoag piloted the HL-10 to Mach 1.86 (1,228 mph). Nine days later, NASA pilot Bill Dana flew the vehicle to 90,030 ft, which became the highest altitude reached in the program.

Typical Flight Profile

Moments after being dropped, the XLR-11 rocket engine (same type engine used in the Bell X-l) was ignited by the pilot and speed and altitude increased until the engine was shut down by choice or fuel exhaustion, depending upon the individual mission profile. The lifting bodies normally carried enough fuel for about 100 sec of powered flight and routinely reached altitudes of 50,000 to 80,000 ft and speeds above Mach 1.

Following engine shutdown, the pilot maneuvered the vehicle through a simulated return-from-space corridor into a pre-planned approach for a landing on one of the lakebed runways on Rogers Dry Lake at Edwards. A circular approach was used to lose altitude during the landing phase. On the final approach leg, the pilot increased his rate of descent to build up energy. At about 100-ft altitude, a "flare out" maneuver dropped air speed to about 200 mph for the landing.

The HL-10 helped develop energy management and landing techniques used presently with the Space Shuttle orbiters.

Specifications

Controls: Elevons between vertical and center fins for pitch and roll control. Split rudder on center fin for yaw and speed control. All surfaces used in three-axis stabilizer-augmenter system.

Power: One XLR-11 four-chamber rocket engine fueled by ethyl alcohol and liquid oxygen, producing maximum of 6,000 lb thrust; built by Chemical Reaction Motors, Inc.

Auxiliary Power: Silver zinc batteries provided electrical power for control system, flight instruments, radios, cockpit heat, and stability augmentation system. To assist in pre-landing flare, four throttleable hydrogen peroxide rockets provided up to 400 lb of thrust.

Landing Gear: Main gear was modified T-38 system retracted manually, and lowered by nitrogen pressure. Nose gear was modified T-39 nose gear, retracted manually and lowered with nitrogen pressure.

Pilot Ejection System: Modified F-106 system.

Modified: February 2, 1994