Die deutsche Version der Readme finden Sie im Anschluá an die englische Version der Readme ! ******************************************************************* * * * Drivers and Applications * * * * for * * * * SPEA MEDIA XTC * * * * Drivers for WINDOWS 3.1x 1095.1 * * Drivers for WINDOWS 95 0995.1 * * Super JAM! Jr. 1.0 * * * * SPEA Software AG Rel.: 1095.1 * ******************************************************************* This README file contains the following information: A) Notes and known problems B) Corrections to the manual C) Windows 95 D) Information about Super Jam! Jr. A) Notes and knows problems Please also read the notes in Appendix B - Troubleshooting in the Hardware User manual. Installation of the Windows 3.1x driver Important! Different to the manual the Intel ICU Plug & Play Utility is NOT delivered with the SPEA MEDIA XTC. The configuration and installation of the soundboard can now be executed under DOS / Windows 3.1x also without Plug & Play functionality (without ICU Utility and without Plug & Play BIOS in the system). In this case, the configuration of the I/O addresses, Interrupts and DMA channels can be done by the SSINIT utility, which you can find in the installation directory (in general C:\SPEA\MEDIAXTC). Start SSINIT under DOS without any parameter. Select the Option `Advanced'. In the following you can change the settings of the board in the menu option `Hardware'. If you have installed a mouse driver under DOS, you can comfortably make the selections with the mouse. If you don't want to make the hardware settings on your own, you should install the Intel ICU Plug & Play Utility on your system before you install the board. The program can be obtained by your local dealer. The configuration of the SPEA MEDIA XTC then will be executed automatically by this program. Please note, that without an installed Plug & Play fuctionality the SPEA MEDIA XTC will be set to the default values I/O=330, DMA=1, IRQ=9 and IRQ=5. Perhaps conflicts with other system components may occur with these settings. Q: After the SPEA MEDIA XTC Windows 3.1x driver installation the system reboots. During the booting process the system crashes while executing the program SSINIT. A: You have installed your SPEA MEDIA XTC without having installed a Plug & Play Utility on your system and with the default I/O addresses, DMA channel or Interrputs conflicts occur between the SPEA MEDIA XTC and other system components. Boot your system without starting SSINIT (e.g. with a DOS boot disk or by pressing the F8 key while booting and confirming each executable command separately). Change to the installation directory (in general C:\SPEA\MEDIAXTC). Start SSINIT without any parameter and select the option `Advanced'. Now you can configure the settings of the soundboard in the `Hardware' menu. May be that you have to enter the following commands before you start SSINIT: SET BLASTER=A220 1xx Dx T1 SET SNDSCAPE=C:\SPEA\MEDIAXTC Alternatively you can edit the file SNDSCAPE.INI directly: Open the file SNDSCAPE.INI -which you will find in the installation directory - with an editor (e.g. the DOS-Editor EDIT) and change the parameter values of IRQ, SBIRQ and DMA corresponding to your requirements. For possible values for Interrupts and DMA channels please refer to the SPEA MEDIA XTC hardware manual in Appendix C - Technical Data. Q: Different to the manual the installation doesn't offer the option for a volume level control to be installed in the AutoStart group. The Level Control Utility will not be installed. A: Different to the description in the manual in Part 2 - Installing the SPEA MEDIA XTC, the Level Control Utility is not supplied and installed with the soundboard, as there are compatibility problems with Windows 95. Q: The diagnostic Utility S2KSTAT - described in the manual in Part 3 - Configuration of the SPEA MEDIA XTC is not executable. It terminates with an error message. A: To get use of the diagnostic Utility S2KSTAT you have to add the following line to the file SNDSCAPE.INI. CodeFile=SNDSCAPE.C03 Now you can use the program. Q: The SPEA MEDIA XTC can not be installed under Windows 95 as described. Either the board cannot be detected by the system or the driver tells (in the Windows 95 device manager) that actually there are no conflicts but that the board is not ready for use or that the driver installation is incomplete. A: In such a case the Plug & Play functionality under Windows 95 is seriously disrupted. This most likely occurs with an elder or a defective System BIOS. Contact your local dealer or the motherboard manufacturer and ask for a System BIOS update. Q: Windows 95 or the SPEA MEDIA XTC Windows 95 driver reports a conflict between the SPEA MEDIA XTC and another installed device. A: Eventually Windows 95 has not recognized the Ensoniq Soundscape chip set of the SPEA MEDIA XTC due to an error with the Plug & Play functionality and therefore installs the Soundboard as an unknown device. Remove the unnknown devices and the SPEA MEDIA XTC entries with the device manager of Windows 95. Restart Windows 95 and follow the instructions of Windows 95, in case that it requires driver disks. Q: After a -as it seems- successful installation of the SPEA MEDIA XTC Windows 95 driver the network card, the mouse or another device does not work propely any more. A: These problems can have several reasons: - An elder Plug & Play BIOS or one that is incompatible to Windows 95 can cause the described effect. After you update the BIOS, the problem should be solved. - If your BIOS offers the possibility to mark IRQs as reserved, it may be necessary that you mark the IRQs as reserved that are reserved by ISA boards without Plug & Play functionality. - May be that conflicts between different devices already occured before the Installation of the SPEA MEDIA XTC. The devices could have worked properly without any errors before, though the error has already been existing. In the device manager check, if there are conflicts between other devices and change the configuration of these devices. Q: After a - as it seems - successful installation of the SPEA MEDIA XTC Windows 95 driver the SPEA MEDIA XTC doen not work. A: These problems can have several reasons: - An elder Plug & Play BIOS or one that is incompatible to Windows 95 can cause the described effect. After you update the BIOS, the problem should be solved. - If your BIOS offers the possibility to mark IRQs as reserved, it may be necessary that you mark the IRQs that are reserved by ISA boards without Plug & Play functionality as reserved. - May be that conflicts between different devices already occured before the Installation of the SPEA MEDIA XTC. The devices could have worked properly without any errors before, though the error has already been existing. In the device manager check, if there are conflicts between other devices and change the configuration of these devices. - In some cases it can be necessary to reconfigure the SPEA MEDIA XTC, to select another Interrupt or DMA channel, though obvioulsy no problem occurs. It may be that other components or their drivers cause errors on Interrupts or DMA channels they actually don't reserve. It may also be that a motherboard has problems with some certain interrupts or DMA channels if a board is installed in an expansion slot. B) Corrections to the manual P. 9 Installation via a Plug & Play System or Utility (ICU): If you don't have a Plug & Play Utility (e.g. Intel's ICU) or Plug & Play BIOS in your system, then you can also configure your SPEA MEDIA XTC with the SSINIT Utility (without Plug & Play functionality). Though it is adviced to purchase a Plug & Play Utility at your local dealer or motherboard manufacturer. P. 11 Internal Audio Connectors / Mitsumi CD (J5): Different to the description and the illustration on page 10 the Audio Connector J5 for a Mitsumi CD is not available on the SPEA MEDIA XTC. P. 13 Installation of the Software for DOS / Windows 3.1: For compatibility reasons (with Windows 95) the Level Control Utility described under item 6 is no longer part of the delivery scope. This means also that there is no possibility for setting up the Volume Level control in the Autostart group of Windows. P. 14 Standard Modifications AUTOEXEC.BAT The 2nd line which will be added to the AUTOEXEC.BAT now is: SET SNDSCAPE= The 3rd line is: \SSINIT /I P. 18 Description of the Options for the Hardware Settings: The options of the Hardware Settings are only available for SSINIT, if the SPEA MEDIA XTC is configured without Plug & Play functionality, that means that Intel's ICU is not installed. C) Windows 95 The SPEA MEDIA XTC is supplied with drivers for Windows 3.1x as well as drivers for Windows 95. Please use the drivers that fit to your operating system. The drivers are available on the supplied disk or on the Media Gallery CD Edition Nr. 12/95 upwards. The supplied applications Super JAM! Jr. and Recording Session Plus can be used under Windows 3.1x and under Windows 95. D) Notes to Super JAM! JR. from the Blue Ribbon Soundworks The Program SuperJAM! Jr. from The Blue Ribbon Soundworks is a powerful program which makes it very easy to compose. When you have successfully installed your Software you can get aware of the program very easy with the available online help. Installation of the Software: 1. Insert the Super JAM! Jr. Installation disk in the corresponding disk drive. 2. Start Windows (if not already done) 3. Start the Software installation from the Program Manager with the following call: `File' `Run' A:\SETUP.EXE 4. Follow the instructions on the screen. The program is copied onto your hard disk. ******************************************************************* * * * Treiber und Applikationen * * * * fr * * * * SPEA MEDIA XTC * * * * Treiber fr WINDOWS 3.1x 1095.1 * * Treiber fr WINDOWS 95 0995.1 * * Super JAM! Jr. 1.0 * * * * SPEA Software AG Rel.: 1095.1 * ******************************************************************* Diese Readme Datei enth„lt folgende Informationen: A) Hinweise und bekannte Probleme B) Žnderungen zum Handbuch C) Windows 95 D) Hinweise zu Super JAM! Jr. A) Hinweise und bekannte Probleme Beachten Sie bitte auch die Hinweise im Anhang B - Probleml”sungen des Handbuches. Installation der Treiber fr Windows 3.1x Achtung: Anders als im Handbuch beschrieben, wird die MEDIA XTC nicht mehr mit dem Intel ICU Plug & Play Utility ausgeliefert. Die Konfiguration und Installation der SPEA MEDIA XTC kann jetzt unter DOS / Windows 3.1x auch ohne Plug & Play-Funktionalit„t (ohne ICU Utility und ohne Plug & Play BIOS im Rechner) ausgefhrt werden. Die Konfiguration der I/O Adressen, der Interrups und DMA-Kan„le erfolgt in diesem Fall mit dem Utility SSINIT, das Sie im Installationsverzeichnis (in der Regel ist dies C:\SPEA\MEDIAXTC) finden. Starten Sie hierzu SSINIT unter DOS ohne Parameter. W„hlen Sie die Option 'Advanced' aus, anschlieáend k”nnen Sie im Men 'Hardware' die Einstellungen der Karte „ndern. SSINIT k”nnen Sie bequem mit der Maus bedienen, wenn unter DOS ein Treiber fr Ihre Maus installiert ist. M”chten Sie die Hardwareeinstellungen (I/O-Adresse, Interrupt und DMA- Kanal) nicht selber vornehmen mssen, sollten Sie das Intel Plug and Play Utility ICU vor der Installation der SPEA MEDIA XTC auf Ihrem PC installieren. Sie erhalten dies von Ihrem PC Fachh„ndler. Die Konfiguration der SPEA MEDIA XTC erfolgt dann automatisch durch das ICU Utility. Beachten Sie bitte, daá bei einer Installation ohne installierte Plug & Play Funktionalit„t die SPEA MEDIA XTC auf die Standardwerte I/O=330, DMA=1 und IRQ=9 sowie IRQ=5 voreingestellt wird. Eventuell kann es mit anderen Systemkomponenten zu Konflikten kommen. F: Nach der Installation der Windows-Treiber der SPEA MEDIA XTC fhrt das System einen Neustart durch. W„hrend des Bootens strzt das System beim Ausfhren von SSINIT ab. A: Sie haben die SPEA MEDIA XTC installiert, ohne Plug & Play auf Ihrem System installiert zu haben und mit der Standard I/O-Adressen, dem Standard DMA-Kanal oder einer der Standard Interrupts kommt es zu einem Konflik zwischen SPEA MEDIA XTC und einer anderen Komponente Ihres Systems. Booten Sie Ihr System, ohne daá SSINIT ausgefhrt wird (z.B. mit einer DOS Boot-Diskette oder indem Sie beim Booten die Taste F8 gedrckt halten und die auszufhrenden Befehle einzeln best„tigen). Wechseln Sie in das Installationsverzeichnis (in der Regel ist dies C:\SPEA\MEDIAXTC). Starten Sie SSINIT ohne Angabe von Parametern und w„hlen Sie die Option 'Advanced' aus. Anschlieáend k”nnen Sie im Men 'Hardware' die Konfiguration der SPEA MEDIA XTC entsprechen Ihres Systems „ndern. Gegebenenfalls mssen Sie vor dem Aufruf von SSINIT die zwei folgenden Zeilen eigeben: SET BLASTER=A220 Ixx Dx T1 SET SNDSCAPE=C:\SPEA\MEDIAXTC Alternativ k”nnen Sie auch die Datei SNDSCAPE.INI direkt editieren: ™ffnen Sie die Datei SNDSCAPE.INI, die Sie im Installationsverzeichnis finden, mit einem Editor (z.B. EDIT von MS-DOS) und ver„ndern Sie die Werte hinter den Parametern IRQ, SBIRQ und DMA entsprechend Ihren Erfordernissen. M”gliche Werte fr Interrupt und DMA-Kan„le entnehmen Sie bitte dem Handbuch Anhang C - Technische Daten. F: Anders als im Handbuch beschrieben, bietet die Installation der Treiber fr Windows 3.1x nicht die Option, einen Lautst„rkeregler in der Autostartgruppe zu installieren. Das Level Control Utility wird nicht installiert. A: Anders als im Handbuch unter Teil 2 - Installation der SPEA MEDIA XTC beschrieben, wird das Level Control Utility aus Grnden der Kompatibilit zu Windows 95 nicht mehr mit der SPEA MEDIA XTC ausgeliefert und installiert. F: Das im Handbuch unter Teil 3 - Konfiguration der SPEA MEDIA XTC beschriebene Diagnose Utility S2KStat l„át sich nicht ausfhren. Es bricht mit einer Fehlermeldung ab. A: Um das Utility S2KStat nutzen zuk”nnen, mssen Sie der Datei SNDSCAPE.INI die folgende Zeile hinzufgen. Dann l„át sich S2KStat nutzen. CodeFile=SNDSCAPE.CO3 F: Unter Windows 95 l„át sich die SPEA MEDIA XTC nicht wie beschrieben installieren. Entweder Findet das System keine Karte oder der Treiber meldet (im Windows 95 Ger„temanager) daá zwar keine Konflikte vorliegen, jedoch das Ger„t nicht betriebsbereit sei oder die Treiberinstallation unvollst„ndig sei. A: In einem solchen Fall kommt es zu einer schweren St”rung der Plug & Play Funktionalit„t von Windows 95. In der Regel liegt dies an einem ver„lteten oder fehlerhaften System-BIOS. Wenden Sie sich an Ihren PC Fachh„ndler oder Motherboard-Hersteller und fragen diesen nach einem BIOS-Update. F: Windows 95 bzw. der Windows 95 Treiber der SPEA MEDIA XTC meldet einen Konflikt zwischen der SPEA MEDIA XTC und einem anderen installierten Ger„t. A: Eventuell hat Windows 95 durch eine St”rung der Plug & Play Funktionalit„t den Ensoniq Soundscape Chipsatz der SPEA MEDIA XTC erkannt und als unbekanntes Ger„t installiert. Entfernen Sie mit dem Ger„temanager von Windows 95 die unbekannten Ger„te und die SPEA MEDIA XTC Eintr„ge. Starten Sie Windows 95 neu und folgen Sie den Anweisungen von Windows 95, falls es nach Treiberdisketten verlangt. F: Nach der anscheinend problemlosen Installation der SPEA MEDIA XTC Treiber fr Windows 95 funktioniert die Netzwerkkarte, die Maus oder ein anderes Ger„t nicht mehr. A: Ausfallserscheinungen anderer Ger„te nach der Installation der SPEA MEDIA XTC unter Windows 95 k”nnen verschiedene Grnde haben: - Bei veralteten oder zu Windows 95 inkompatiblen Plug & Play BIOSen kann es zu den beschriebenen Effekten kommen. Nach einem Update des BIOSes ist das Problem meist behoben. - Besitzt Ihr BIOS die Moglichkeiten IRQs als belegt zu markieren, ist es m”glicherweise notwendig, die durch ISA-Karten ohne Plug & Play Funktionalit„t belegten IRQs im BIOS als belegt zu markieren. - Eventuell bestanden schon vor der Installation der SPEA MEDIA XTC zwischen verschiedenen Komponenten Konflikte. Einige Ger„te k”nnen eventuell auch trotz eines vorhandenen Konfliktes vor der Installation der SPEA MEDIA XTC problemlos funktioniert haben. šberprfen Sie im Ger„temanager, ob eventuell Konflikte zwischen Ger„ten vorliegen und „ndern Sie die Konfiguration dieser Ger„te. F: Nach der anscheinend problemlosen Installation der SPEA MEDIA XTC Treiber fr Windows 95 funktioniert SPEA MEDIA XTC nicht. A: Fehlfunktionen nach der Installation der SPEA MEDIA XTC unter Windows 95 k”nnen verschiedene Grnde haben: - Bei veralteten oder zu Windows 95 inkompatiblen Plug & Play BIOSen kann es zu diesem Fehlverhalten kommen. Nach einem Update des BIOSes ist das Problem meist behoben. - Besitzt Ihr BIOS die Moglichkeiten IRQs als belegt zu markieren, ist es m”glicherweise notwendig, die durch ISA-Karten ohne Plug & Play Funktionalit„t belegten IRQs im BIOS als belegt zu markieren. - Eventuell bestanden schon vor der Installation der SPEA MEDIA XTC zwischen verschiedenen Komponenten Konflikte. Einige Ger„te k”nnen eventuell auch trotz eines vorhandenen Konfliktes vor der Installation der SPEA MEDIA XTC problemlos funktioniert haben. šberprfen Sie im Ger„temanager, ob eventuell Konflikte zwischen Ger„ten vorliegen und „ndern Sie die Konfiguration dieser Ger„te. - In einigen F„llen kann es notwendig sein die SPEA MEDIA XTC auf eine andere Konfiguration umzustellen und einen anderen Interrupt oder DMA- Kanal zu w„hlen, obwohl anscheinend kein Konflikt vorliegt. Es kann vorkommen, daá andere Komponenten oder deren Treiber St”rungen auf Interrupts oder DMA-Kan„len verursachen, die sie eigentlich nicht belegen. Ebenso kann es vorkommen, daá ein Motherboard einfach auf bestimmten Interrups oder DMA-Kan„len Probleme mit bestimmten Steckkarten hat. B) Žnderungen zum Handbuch S. 9 Installation ber ein Plug & Play-System bzw. Utility (ICU): Verfgen Sie auf Ihrem System nicht ber ein Plug and Play Utility (z.B. ICU von Intel) oder ein Plug & Play BIOS, dann k”nnen Sie die SPEA MEDIA XTC auch ber das SSINIT Utiliy (ohne Plug and Play Funktionalit„t) konfigurieren. Es wird allerdings empfohlen, daá Sie sich ein Plug and Play Utility (z.B. ICU von Intel) von Ihrem PC Fachh„ndler oder Motherboard- Hersteller besorgen. S. 11 Interne Audioanschlsse / Mitsumi CD (J5): Anders als auf Seite 11 beschrieben und in der Zeichnung auf Seite 10 eingezeichnet ist der Audioanschluá J5 fr Mitsumi CD auf der SPEA MEDIA XTC nicht bestckt. S. 13 Installation der Software fr DOS/Windows 3.1: Das unter 6. beschriebene Level Control Utility geh”rt aus Grnden der Kompatibilit„t zu Windows 95 nicht mehr zum Lieferumfang. W„hrend der Installation gibt es daher auch keine Auswahl mehr, die es erm”glicht das Level Control Utility in der Autostart Gruppe von Windows einzurichten. S. 14 Standardanpassungen / AUTOEXEDC.BAT Die zweite Zeile, die in die AUTOEXEC.BAT Datei eingefgt wird, heiát richtig: SET SNDSCAPE= Die dritte Zeile, die in die AUTOEXEC.BAT Datei eingefgt wird, heiát richtig: \SSINIT /I S. 18 Beschreibung der Optionen der Hardware Einstellungen: Die Optionen der Hardware Einstellungen stehen in SSINIT nur zur Verfgung, wenn die SPEA MEDIA XTC ohne Plug & Play Funktionalit„t Konfiguriert wird, d.h. Intels ICU nicht installiert ist. C) Windows 95 Der SPEA MEDIA XTC liegen Treiber sowohl fr Windows 3.1x als auch fr Windows 95 bei. Bitte verwenden sie die Ihrem Betriebsystem entsprechenden Treiber. Sie finden diese auf den beiliegenden Disketten bzw. auf der beiliegenden MediaGallery CD-ROM ab Ausgabe 12/95. Die beiliegenden Applikationen Super JAM! Jr. und Recording Session Plus k”nnen Sie sowohl unter Windows 3.1x als auch unter Windows 95 einsetzen. D) Hinweise zu Super JAM! Jr. von The Blue Ribbon Soundworks Das Program SuperJAM Jr. von The Blue Ribbon Soundworks ist ein leistungsf„higes Programm mit dem sich spielend leicht komponieren l„át. Sobald Sie die Software erfolgreich installiert haben, k”nnen Sie sich mittels Online-Hilfe selbst schnell zurechtfinden. Installation der Software: 1. Legen Sie die Super JAM! Jr. Installationsdiskette in das entsprechende Laufwerk. 2. Starten Sie Windows (sofern noch nicht geschehen) 3. Starten Sie die Installation aus dem Programm-Manager mit dem Aufruf: 'Datei' 'Ausfhren' A:\SETUP.EXE 4. Folgen Sie den Anweisungen am Bildschirm. Das Programm wird auf Ihre Festplatte installiert.